7422 Gall Blvd (8) - Laserfiche WebLink

Browse Search

REVISIONS PROGRAM OVERVIEW: THE "CONTRACTOR" WILL INSTALL A TV SIGNAL DISTRIBUTION SYSTEM INTO A NEW SEARS HOLDINGS CORPORATION LOCATION AT THE FOLLOWING ADDRESS: KMART #4867,100 MAIN STREET NORTH, SOUTHBURY, CT. 1. THE DISTRIBUTION SYSTEM WILL PROVIDE NTSC AND ATSC SIGNALS AT LOCATIONS SPECIFIED ON THE "FINAL FIXTURE PLAN" 2, THE DISTRIBUTION SYSTEM WILL PROVIDE UP TO EIGHT (8) ATSC/NTSC ZONES AND EACH ZONE WILL BE PROVIDED WITH A COMMSCOPE PLENUM CABLE HOMERUN FROM THE TV AMPLIFIER TO THE DIRECTIONAL TAPS NOTED BELOW. 3. SIGNAL QUALITY WILL COMPLY WITH ALL APPLICABLE FCC GUIDELINES AND DELIVER A MINIMUM SIGNAL STRENGTH OF +3 DBMV AT THE TELEVISION TERMINALS. SIGNAL-TO-NOISE MUST BE GREATER THAN +40 DBMV FOR NTSC AND GREATER THAN OR EQUAL TO +20 DBMV FOR ATSC AS MEASURED AT THE TELEVISION TERMINALS. 4, AT EACH STORE LOCATION, THE INSTALLATION WILL FOLLOW A UNIQUE PHASING/INSTALLATION SCHEDULE. INSTALL REQUIREMENTS: THE "CONTRACTOR" WILL PROVIDE AN INSTALLED AV DISTRIBUTION SYSTEM INCLUDING ALL NECESSARY EQUIPMENT (EXCEPT AS NOTED TO BE PROVIDED BY OTHERS), MATERIAL, LABOR, APPLICABLE TAXES AND PERMITS, AND OTHER RELATED SERVICES. 1. COORDINATE THE AV SYSTEM INSTALLATION TIME AND THE STORE PHASING SCHEDULE WITH THE SEARS PROJECT MANAGER. 2. PROVIDE THE EQUIPMENT LISTED (WITHOUT SUBSTITUTE) FOR THE AV SIGNAL DISTRIBUTION SYSTEM. 3. INSTALL THE EQUIPMENT LISTED, AS PER THE ATTACHED WIRING DIAGRAMS, FOLLOWING TIA/EIA STANDARDS COAXIAL CABLING. 4, PROVIDE ALL CORRESPONDING PATCH CABLING BETWEEN TV SETS AND CABLE RACEWAY "F" CONNECTORS. THE FINAL CONNECTIONS WILL BE DONE BY OTHERS WHEN MERCHANDISE ARRIVES. 5. COORDINATE WITH THE SEARS PROJECT MANAGER AND PROVIDE TRAINING FOR SEARS STORE PERSONNEL. INSTALL ACCEPTANCE PROCESS: THE "AV CONTRACTOR" WILL PREPARE AN INSTALLATION COMPLETION CHECKLIST. THE CHECKLIST WILL BE PRESENTED TO THE SEARS PROJECT MANAGER FOR HIS/HER SIGNATURE WITHIN 48 HOURS OF THE COMPLETION OF WORK. WARRANTY: THE "AV CONTRACTOR" SHALL PROVIDE ONE YEAR OF FULL WARRANTY COVERING MATERIAL, EQUIPMENT AND LABOR ON INSTALLATION PROVIDED. MATERIALS: THE "AV CONTRACTOR" WILL PROVIDE THE FOLLOWING LIST OF MATERIALS FOR INSTALLATION: QUANTITIES WILL CHANGE FOR EACH JOB BASED ON THE FINAL FIXTURE PLAN. AN ACCURATE TAKEOFF IS REQUIRED. SUBSTITUTION OF MANUFACTURERS IS NOT PERMITTED. (1) PICO-MACOM TRU-SPEC TA-36 AMPLIFIER (KAMRT) (1) PICO-MACOM CA45RK550 AMPLIFIER (SEARS) (1) RF SPUTTER/COMBINER (2 IN -1 OUR) -7DB (1) TONER CABLE 8 PORT DIRECTIONAL TAP (TAKEOFF Q7 COMMSCOPE RG6 CABLE (TAKEOFF QTY) T&B PLENUM RG6 "F" CONNECTOR (TAKEOFF) "F" 75 OHM TERMINATOR CAPS (X) "F" JACK RACEWAY/CABLE TRAY HOUSING FOR SECURTIY OF SENCORE UNIT (1) MIDDLE ATLANTIC SWING WALL MOUNTED CABINET (1) MIDDLE ATLANTIC UNIVERSAL CABINET SHELVES (1) MIDDLE ATLANTIC HORIZONTAL POWER STRIP SEARS WILL PROVIDE THE FOLLOWING EQUIPMENT: ONE (1) SENCORE HDTV PLAYER (POWS#HDTV996A) CONTRACTOR SCOPE OF WORK: MODEL BIDA 75A-30 GENERIC MODEL TGT8-20 MODEL 2275K MODEL PL56CS GENERIC GENERIC MODEL DWR-10-17 MODELU2 MODEL PD-815R-PL 1, COORDINATE A SITE VISIT WITH THE SEARS PROJECT MANAGER TO DETERMINE THE SENCORE, AMPLIFIER AND TELEVISION LOCATIONS THAT MAKE DISTRIBUTION POINTS OF THE AV SYSTEM. 2. INSTALL THE SENCORE UNIT AND FOLLOW THE ATTACHED INITIALIZATION PROCEDURE, 3. INSTALL ONE 2 IN -1 OUT RF SPLITTER/COMBINER TO JOIN THE TWO OUTPUTS OF THE SENCORE UNIT INTO ONE SINGLE OUTPUT CABLE RUNNING TO THE TA-36 AMPLIFIER LOCATED AT IN THE ELECTRICAL DEPARTMENT. THE FINAL LOCATION IS TO BE COORDINATED WITH THE SEARS PROJECT MANAGER 4. RUN RG-6 COAXIAL CABLE FROM THE AMPLIFIER TO THE TONER 8 PORT SPUTTER, 5. RUN RG-6 COAXIAL CABLE FROM THE TONER 8 PORT SPUTTER TO TONER 4 PORT DIRECTIONAL TAPS, IN QUANTITY NEEDED BASED UPON THE NUMBER OF TELEVISION CONNECTIONS ANTICIPATED. CABLE TO BE RUN WITHIN THE SPECIFIED CABLE RACEWAY. & RUN RG-6 COAXIAL CABLE FROM THE 4 PORT DIRECTIONAL TAPS TO THE "F" CONNECTORS OF THE RACEWAY TO A POSITION CLOSEST TO THE TELEVISION BEING CONNECTED TO THE SYSTEM. 7. ALL CABLE, EXCEPT FROM RACEWAY TO TELEVISION, TO BE CONCEALED ABOVE THE CEILING, WITHIN WALL CAVITY IF ALLOWED BY CODE, IN -WALL CONDUIT IF REQUIRED BY CODE AND WITHIN THE CABLE RACEWAY FIXTURE MOUNTED BEHIND THE TELEVISIONS. 8. RUN RG-6 COAXIAL CABLE FROM THE RACEWAY "F" CONNECTOR TO THE TELEVISION BEING CONNECTED TO THE SYSTEM 9. TEST AND ADJUST THE SYSTEM PERFORMANCE TO MANUFACTURERS REQUIREMENTS. SENCORE HDTV996A INSTALLATION AND CONFIGURATION -ALL STORES KMART STORES/ SENCORE HDTV996A PLAYER ITEMS FURNISHED BY SEARS HOLDING CORPORATION QTY ITEM 1 SENCORE HDTV996A PLAYER 1 INSTALLATION GUIDE 1 PICO-MACOM TRU-SPEC TA-36 AMPLIFIER 4 TONER 8-CONNECTION TAPS SEARS STORES FULL LINE AND GRAND/ SENCORE HDTV996A PLAYER ITEMS FURNISHED BY SEARS HOLDING CORPORATION QTY ITEM 1 SENCORE HDTV996A PLAYER 1 INSTALLATION GUIDE SEARS STORES FULL LINE AND GRAND- SENCORE HDTV996A PLAYER ITEMS FURNISHED BY CONTRACTOR QTY ITEM 1 PICO-MACOM CA45RK550 AMPLIFIER 4 TONER 8-CONNECTION TAPS INITIAL CONFIGURATION PLEASE READ ALL THE STEPS BELOW BEFORE BEGINNING THE CONFIGURATION. 1. TO START THE SENCORE HDTV996A, VERIFY THAT POWER IS APPLIED FROM THE POWER STRIP AND PRESS THE POWER BUTTON. THE PLAYER WILL GO THROUGH AN INITIALIZATION PERIOD (ABOUT 1 MINUTE). 2. CONFIRM THAT THE SENCORE HDTV996A IS CONFIGURED TO OUTPUT ATSC CHANNEL 14 AND NTSC CHANNEL 3. SEE THE CHANNEL SETUP IN THE MODIFYING CONFIGURATION SECTION. 3. CONFIRM THAT THERE IS AN ASTERISK" NEXT TO PLAY IN THE STATUS WINDOW. (EXAMPLE: PLAY*). THIS INDICATES THAT THE PLAYER WILL PLAY ALL AVAILABLE VIDEO CLIPS REPEATEDLY. SEE THE PLAYBACK SETUP - PLAY ALL IN THE MODIFYING CONFIGURATION SECTION. 4. GO THE SALES FLOOR AND CONFIRM THAT ALL THE ANALOG TVS ARE SHOWING THE "HAWAII" VIDEO CLIP ON CHANNEL 3. USE THE REMOTE CONTROL AND SELECT CHANNEL 3. 5. THE TVS WITH THE NEW INTEGRATED OR BUILT-IN DIGITAL TUNERS MAY HAVE TO BE REPROGRAMMED TO RECOGNIZE CHANNEL 14 DIGITAL. ASK THE SALES ASSOCIATE WHICH TV'S HAVE THIS FEATURE SO YOU CAN CONFIRM THE SENCORE HDTV996A IS PROVIDING CHANNEL 14 CORRECTLY, MODIFYING CONFIGURATION STARTING THE HDTV996A OUTPUT AFTER THE PLAYER IS POWERED ON, PRESS THE PLAY BUTTON TO PLAYTHE PRERECORDED PROGRAMMING THAT IS INSTALLED ON THE INTERNAL HARD DRIVE. STOPPING THE HDTV996A OUTPUT AFTER THE PLAYER IS POWERED ON, PRESS THE STOP BUTTON TO STOP PLAYING THE PRERECORDED PROGRAMMING THAT IS INSTALLED ON THE INTERNAL HARD DRIVE. POWERING OFF OR SHUTTING DOWN THE HDTV996A TO SHUT THE PLAYER DOWN, PRESS THE POWER BUTTON AND THE PLAYER WILL GO INTO SHUT DOWN MODE. THE SCREEN WILL DISPLAY THE FOLLOWING: "SYSTEM SHUT DOWN SHUTTING DOWN.,. PLEASE WAIT" FOR ABOUT 10 SECONDS. DO NOT DISCONNECT THE POWER CORD UNTIL THE STATUS SCREEN IS BLACK (BLANK) AND THE HDTV996A IS OFF. CHANNEL SETUP 1. PRESSING THE MENU/EXIT BUTTON WHILE IN ANY WINDOW WILL TAKE YOU INTO THE MENU WINDOW. IF YOU ARE ALREADY IN THE MENU WINDOW IT WILL TAKE YOU BACK TO THE WINDOW YOU WERE IN PRIOR TO THE MENU WINDOW (GENERALLY THE PLAYER STATUS WINDOW). 2. PRESSING THE UP AND DOWN ARROW KEYS WILL MOVE THE CURSOR TO THE VARIOUS OPTIONS IN THE MENU WINDOW. DO SO UNTIL THE EITHER ATSC CHANNEL OR NTSC CHANNEL IS SELECTED AS SHOWN IF THE FIGURE BELOW. WITH THE CURSOR ON THE ATSC CHANNEL SELECTION PRESS ENTER. THIS WILL TAKE YOU INTO A NEW WINDOW WHERE YOU CAN USE THE UP/DOWN ARROW KEYS OR THE ALPHANUMERIC KEYPAD TO ENTER CHANNEL 14, WITH THE CURSOR ON THE NTSC CHANNEL SELECTION PRESS ENTER. THIS WILL TAKE YOU INTO A NEW WINDOW WHERE YOU CAN USE THE UP/DOWN ARROW KEYS OR THE ALPHANUMERIC KEYPAD TO ENTER CHANNEL 3. NOTE: INTERFERENCE WILL HAPPEN IF THE NTSC CHANNEL FROM THE SENCORE HDTV996A IS SET TO A CHANNEL IMMEDIATELY ABOVE A LOCAL CHANNEL THAT IS RECEIVED BY THE STORE'S RF DISTRIBUTION SYSTEM. SET THE HDTV996A NTSC CHANNEL AT TWO CHANNELS APART. EXAMPLE: HDTV996A IS SET TO NTSC CHANNEL 8 AND LOCALLY NTSC CHANNEL 7 IS RECEIVED BY THE STORE'S ROOF ANTENNA AND IS ONE OF THE AVAILABLE CHANNELS TO DEMONSTRATE TV PERFORMANCE. IN THIS CASE THE HDTV996A SHOO BE SET TO EITHER NTSC CHANNEL 6 OR NTSC CHANNEL 9. PLAYBACK SETUP PLAYLIST RECALL: PRESSING THE PLAYLIST RECALL BUTTON, WHILE IN ANY WINDOW WILL TAKE YOU INTO THE PLAYLIST RECALL WINDOW. THE NUMBERS, IN MINUTES, TO THE RIGHT OF THE FILE NAMES INDICATES THE LENGTH OF THE FILE. TO PLAY A FILE, SIMPLY MOVE THE CURSOR WITH THE UP/DOWN ARROW KEYS TO THE LEFT OF THE DESIRED FILE AND PRESS ENTER OR PLAY. THE FILE WILL BE PLAYED IN A CONTINUOUS LOOP UNTIL STOPPED OR PAUSED BY THE USER. PLAY ALL: (DEFAULT) SELECT PLAY ALL, BY MOVING THE CURSOR USING THE UP AND DOWN ARROW KEYS, AND THEN PRESS PLAY. THIS WILL PLAY ALL OF THE FILES CONTAINED ON THE HARD DRIVE IN SEQUENTIAL ORDER (ALPHABETICALLY) ACCORDING TO THE FILE NAME. THE LENGTH IN MINUTES ON THE RIGHT INDICATES THE TOTAL PLAYING TIME OF ALL THE PLAY FILES ON THE HARD DRIVE. SELECTING PLAY ALL WILL ALSO PLACE AN ASTERISK* NEXT TO PLAY IN THE PLAYERS STATUS WINDOW THAT WILL BE DISCUSSED LATER. OPTION'B' HOLLOW RACEWAY OPTION'A F CONNECTOR RACEWAY EXAMPLE ELEVATION FOR POWER AND RACEWAY PLACEMENTS BIDDERS PRINTS ISSUED JANUARY 17, 2007 rn I—� Q OI—{ W c U as w o q) U) -- .cn > w (y) Ed ICY) 0 Q W (C o � x Cn J Q H V z C W H U) U) W// Or- 0 U z Lu W Q 0 J LL ) J <C Lu J_ = J >- o m LLJ J N J Q CD co N 1*-- N i ti ii L u� i 0 c-) rn Q Lu m CO CIO d- Z Q O QJ U w CO CD OOwC Q U) p w C!) _ � � L oI aUC � <C Cn Ire U H Project Arch./ Engineer: R.THORNTON Drawn: D.0 Checked: B.KUHARCHEK Date: JANUARY 17, 2007 Sheet No: