|
3
<br />FIBEREGLASS SHINLGE INSTALLED
<br />AS PER MANUFACTURER
<br />SPECIFICATIONS
<br />12
<br />4.01
<br />--------- ---- +r
<br />FIBEREGLASS SHINLGE INSTALLED
<br />AS PER MANUFACTURER
<br />SPECIFICATIONS
<br />HEEL
<br />00 T
<br />12
<br />5.01
<br />4'
<br />PLASTER ON
<br />FRAME
<br />zo-on ��-ter 12
<br />J 14.0
<br />2ND------------------------------ - �- _ ,_____
<br />FLR ----T 1` - - ----
<br />35-SH
<br />----�--------------------------I---I-
<br />6068 SGD
<br />NG
<br />TEXTURED
<br />F, CEMENTITIOUS
<br />FINISH ON
<br />CMU (TYP)
<br />REAR ELEVATION - A
<br />SCALE: 1/4" = 1'-0"
<br />9'-0" RIDGE VENT
<br />TEXTURED
<br />CEMENTITIOUS
<br />FINISH ON
<br />CMU (TYP)
<br />HDR.
<br />12
<br />% 14.0 2ND
<br />-----
<br />-__ FIN FLR
<br />LEFT ELEVATION - A
<br />SCALE: 1/4" = 1'-0"
<br />General Notes
<br />ROOF CRITERIA:
<br />• 12" OVERHANG U,N•O.
<br />• PLUMB CUT FASCIA ROOF
<br />• PITCH PER ELEVATION
<br />**G.C. VERIFY ROOF PITCH**
<br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE
<br />CONTRACTORS RESPONSIBILITY TO VERIFY
<br />ROOF SLOPE REQUIREMENTS WITH TRUSS
<br />MANUFACTURER.
<br />**ELECTRICAL SPECIFICATION NOTES**
<br />ELECTRICAL CONTRACTOR MUST VERIFY WITH
<br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE
<br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR
<br />LOCATION PURPOSES.
<br />Exterior Covering
<br />R703.7 Exterior Plaster.
<br />Installation of these materials shall be in compliance with ASTM
<br />C926 and ASTM C1063, or ASTM C1787 and the provisions of
<br />this code.
<br />R703.7.1 Lath.
<br />Lath and Lath attachments shall be of corrosion -resistant
<br />materials. Expanded metal or woven wire lath shall be attached
<br />with 1-1/2" long, 11 gage nails having
<br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in
<br />accordance with ASTM C1063 or C1787, or as otherwise
<br />approved. (Refer to sheet SNI for the engineered method for
<br />Lath attachment.)
<br />Lathing Accessories
<br />Attachments shall be of corrosion -resistant materials.
<br />Wood Application: 16 Ga.xl-1/2" long (3/4"A" crown) staples @
<br />6" O.C. vertically/horizontally into the framing members.
<br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia.
<br />min. @ 6" Q.C. vertically/horizontally or compatible adhesives,
<br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C.
<br />or in a semi -continuous bead between the solid plaster base and
<br />the solid portion of the key attachment flange.
<br />Control Joints: Install control joint lathing accessories in
<br />conformance with C1063. Lath shall not be continuous through
<br />control joints, but shall be stopped and tied at each side.
<br />All accessories shall be in accordance with the latest ASTM
<br />C1063 & ASTM C1861.
<br />R703.7.2 Plaster.
<br />Plastering with cement plaster shall be not less than three coats
<br />where applied over any type of code -approved lath and shall be
<br />not less than two coats where directly applied over masonry,
<br />concrete, clay brick, stone, or tile. If the plaster surface is
<br />completely covered by veneer or other facing material or is
<br />completely concealed, plaster application need be only two coats,
<br />provided total thickness is as set in Table R702.1(1).
<br />Cement plaster shall be in accordance with ASTM C926 and
<br />material shall be in accordance with one of the types listed in
<br />R703.7.2.
<br />R703.7.3 Water -Resistive Barriers.
<br />Water -resistive barriers shall be installed as required in Section
<br />R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a
<br />performance at least equivalent to two layers of Grade D paper.
<br />The individual layers shall be installed independently such that
<br />each layer provides a separate continuous plane and any flashing
<br />(installed in accordance with Section R703.4) intended to drain to
<br />the water -resistive barrier is directed between the layers.
<br />R703.2 Water -Resistive Barrier.
<br />One layer of No. 15 asphalt felt, free from holes and breaks,
<br />complying with ASTM D226 for Type 1 felt or other approved
<br />water -resistive barrier shall be applied over studs or sheathing of
<br />all exterior walls. No. 15 asphalt felt shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2
<br />inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance
<br />with the water -resistive barrier manufacturer's installation
<br />instructions. The No. 15 asphalt felt or other approved
<br />water -resistive barrier material shall be continuous to the top of
<br />walls and terminated at penetrations and building appendages in
<br />a manner to meet the requirements of the exterior wall envelope
<br />as described in Section R703.1.
<br />R703.4 Flashing.
<br />Approved metal flashing, vinyl flashing, self -adhered membranes
<br />and mechanically attached flexible flashing shall be applied
<br />shingle -fashion or in accordance with the manufacturer's
<br />instructions. Metal flashing shall be corrosion resistant.
<br />Fluid -applied membranes used as flashing shall be applied in
<br />accordance with the manufacturer's instructions. All flashing shall
<br />be applied in a manner to prevent the entry of water into the wall
<br />cavity or penetration of water to the building structural framing
<br />components.
<br />Self -adhered membranes used as flashing shall comply with
<br />AAMA 711. All exterior fenestration products shall be sealed at
<br />the juncture with the building wall with a sealant complying with
<br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for
<br />proper joint expansion and contraction, ASTM C1281, AAMA 812,
<br />or other approved standard as appropriate for the type of sealant.
<br />Fluid -applied membranes used as flashing in exterior walls shall
<br />comply with AAMA 714. The flashing shall extend to the surface
<br />of the exterior wall finish.
<br />Approved flashings shall be installed at the following locations.
<br />• Exterior window/door openings.
<br />• Intersection of chimneys or other masonry construction with
<br />frame walls.
<br />• Under and at the ends of masonry, wood or metal copings
<br />and sills.
<br />• Continuously above all projecting wood trim.
<br />• Where exterior porches, decks or stairs attach to a wall or
<br />floor assembly of wood -frame construction.
<br />• At wall and roof intersection.
<br />• At Built-in gutters.
<br />Coastal Flashings
<br />All flashing material for coastal locations (ex: within 3,000 feet of the
<br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless
<br />steel) and shall be selected for compatibility with adjacent wood
<br />preservatives per the manufacturer's recommendations.
<br />REV. 09.24.21
<br />e•�
<br />0
<br />7 W
<br />t�
<br />O
<br />o
<br />.�
<br />cc
<br />l l d it llyO�J��
<br />y4�����,t"iiiil
<br />�N4P� •NSE• •.,fin,
<br />&T •�
<br />< •�
<br />03 F
<br />r
<br />S
<br />C
<br />5'(A �4
<br />OFE
<br />/SIO
<br />114,t l/t itSilil'�\�������
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2020 Florida Building Code -
<br />Residential 7th Edition. Engineer's signature and seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />upl
<br />®
<br />ti0
<br />(0
<br />E
<br />O N 8 p
<br />04 .0 'No
<br />0
<br />Y
<br />S
<br />�
<br />1%
<br />19
<br />C
<br />t',O— r�L
<br />m� u_
<br />C J U- W
<br />�� o
<br />— a
<br />a
<br />Z
<br />m c v
<br />LLt
<br />Z
<br />IL IL
<br />yya 0
<br />co N
<br />� °) °) m
<br />J
<br />LO M Z J
<br />a
<br />N
<br />O U 0 0)
<br />Z
<br />W
<br />❑❑
<br />r
<br />� N 0o
<br />O
<br />C N
<br />� �
<br />N
<br />r`
<br />M
<br />v(LL
<br />aJ
<br />d
<br />f`j
<br />0
<br />m
<br />w
<br />JW&
<br />V)
<br />�N
<br />� in
<br />INSLAl
<br />J
<br />a— — E
<br />8
<br />c �••....
<br />M,
<br />Co
<br /><
<br />®®
<br />�m
<br />o
<br />M
<br />M
<br />a
<br />0O
<br />w
<br />Z
<br />G
<br />� cc
<br />f6 E
<br />g�
<br />UJ
<br />as
<br />Z®
<br />�
<br />t—
<br />O E
<br />N
<br />o
<br />Q
<br />az
<br />a
<br />°0
<br />o
<br />0
<br />a,
<br />t
<br />o
<br /><o
<br />r
<br />w�
<br />Zm
<br />rg
<br />z
<br />U
<br />m o
<br />1
<br />Q W
<br />N
<br />Cn j
<br />?
<br /><
<br />o Q
<br />z Z
<br />O
<br />0_
<br />wLL
<br />a
<br />W
<br />0
<br />oco
<br />w
<br />ilo
<br />a
<br />c 0
<br />0
<br />> Lo
<br />rn
<br />ns
<br />y-
<br />�
<br />CU
<br />co
<br />0
<br />i�
<br />0
<br />Q
<br />6
<br />tB
<br />0
<br />'Cr
<br />vJ o
<br />m
<br />L
<br />+�
<br />LO
<br />0
<br />-E
<br />t\
<br />C0
<br />,�
<br />CU N
<br />0
<br />r
<br />Q
<br />ITT N
<br />Lo
<br />LO
<br />r-
<br />E
<br />w
<br />M N
<br />o
<br />z
<br />z
<br />E
<br />(n,
<br />c
<br />a
<br />U .°J
<br />JOB
<br />NO:
<br />22-12352
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />2.2
<br />-T-,-—i-nu- _- I I I I I I i 'i I-d.I i 1i1;J U11l, 1 t Al d: ,,J I I
<br />
|