|
LO
<br />Cr
<br />(n
<br />:19
<br />j�
<br />C)
<br />L0
<br />0
<br />CD
<br />c-4
<br />a
<br />Lc)
<br />60
<br />0
<br />Cr
<br />4%
<br />I-',
<br />E
<br />E
<br />0
<br />a
<br />a
<br />LZ
<br />t5
<br />0
<br />LZ
<br />C14
<br />C14
<br />C)
<br />c*`1
<br />C14
<br />to
<br />NOTE: BORATE/ SENTRA CON SYSTEM APPLIED TO ALL FRAME MEMBERS WITHIN 24" A.F.F.
<br />1) METHOD OF TREATMENT SHALL BE APPROVED BY THE GOVERNING JURISDICTION "LIQUID
<br />BORATE OR BOR-A-COR" PRODUCT METHODS MUST BE DETERMINED AT PERMIT STAGE.
<br />2) PRESSURE TREATED LUMBER THAT HAS BEEN CUT OR DRILLED THAT EXPOSES UNTREATED
<br />PORTIONS OF WOOD ARE REQUIRED TO BE FIELD TREATED TO PREVENTINSECT
<br />INFESTATION.
<br />ATTENTION: CHEMICAL CHANGES IN PRESSURE TREATED WOODS
<br />As OF DECEMBER 31ST, 2003, CHROMATED COPPER ARSENATE (CCA-C) WILL NO LONGER BE PRODUCED FOR RESIDENTIAL OR GENERAL
<br />CONSUMER USE. SEVERAL NEW PRESSURE TREATED WOOD ALTERNATIVES HAVE BEEN CREATED TO REPLACE CCA-C. MANY OF THE NEW
<br />PRESSURE TREATED WOODS USE CHEMICALS THAT ARE CORROSIVE TO STEEL. IT IS THE CONTRACTOR'S RESPONSIBILITY TO VERIFY THE TYPE
<br />OF WOOD TREATMENT AND TO SELECT APPROPRIATE CONNECTORS THAT RESIST CORROSION, FOR EXAMPLE, ACQ-C, ACQ-D, CBA-A, OR CA-B
<br />REQUIRE HOT -DIPPED GALVANIZED OR STAINLESS STEEL FASTENERS. DOT SODIUM BORATE (SBX) DOES NOT.
<br />REQUIRED SAFETY GLAZING IN HAZARDOUS LOCATIONS
<br />(RE: FBRC R308.4)
<br />R308.3 HUMAN IMPACT LOADS. INDIVIDUAL GLAZED AREAS INCLUDING GLASS MIRRORS IN HAZARDOUS LOCATIONS SUCH AS THOSE
<br />INDICATED AS DEFINED IN SECTION R308.4 SHALL PASS THE TEST REQUIREMENTS OF SECTION R308.3.1. GLAZING SHALL BE TESTED
<br />IN ACCORDANCE WITH CPSC 16 CFR, PART 1201 CRITERIA FOR CATEGORY I OR CATEGORY 11 AS INDICATED IN TABLE R308.3.1(1).
<br />EXCEPTIONS:
<br />1. POLISHED WIRED GLASS FOR USE IN FIRE DOORS AND OTHER FIRE RESISTANT LOCATIONS SHALL COMPANY WITH ANSI
<br />Z97.1-14
<br />2. LOUVERED WINDOWS AND JALOUSIES SHALL COMPANY WITH SECTION R308.2
<br />R308.4 HAZARDOUS LOCATIONS.
<br />THE FOLLOWING SHALL BE CONSIDERED SPECIFIC HAZARDOUS LOCATIONS FOR THE PURPOSE OF GLAZING:
<br />1. GLAZING IN SWINGING DOORS EXCEPT JALOUSIES.
<br />2. GLAZING IN FIXEDAND SLIDING PANELS OF SLIDING DOOR ASSEMBLIES AND PANELS IN SLIDING AND BIFOLD CLOSET DOOR
<br />ASSEMBLIES.
<br />3. GLAZING IN STORM DOORS.
<br />4� GLAZING IN ALL UNFRAMED SWINGING DOORS,
<br />5. GLAZING IN DOORS AND ENCLOSURES FOR HOT TUBS, WHIRLPOOLS, SAUNAS, STEAM ROOMS, BATHTUBS, AND SHOWERS.
<br />GLAZING IN ANY PART OF A BUILDING WALL ENCLOSING THESE COMPARTMENTS WHERE THE BOTTOM EXPOSED EDGE OF
<br />THE GLAZING IS LESS THAN 60 INCHES (1524MM) MEASURED VERTICALLY ABOVE ANY STANDING OR WALKING SURFACE.
<br />6. GLAZING, IN AN INDIVIDUAL FIXED OR OPERABLE PANEL ADJACENT TO A DOOR WHERE THE NEAREST VERTICAL EDGE IS
<br />WITHIN A 24-INCH(610MM) ARC OF THE DOOR IN A CLOSED POSITION AND WHOSE BOTTOM EDGE IS LESS THAN 60 INCHES
<br />(1524MM) ABOVE THE FLOOR OR WALKING SURFACE.
<br />7. GLAZING IN AN INDIVIDUAL FIXED OR OPERABLE PANEL, OTHER THAN THOSE LOCATIONS DESCRIBED IN ITEMS 5 AND 6
<br />ABOVE, THAT MEETS ALL OF THE FOLLOWING CONDITIONS:
<br />7.1 EXPOSED AREA OF AN INDIVIDUAL PANE GREATER THAN 9 SQUARE FEET (0.836 M2).
<br />7.2 BOTTOM EDGE LESS THAN 18 INCHES (457 MM) ABOVE THE FLOOR.
<br />7.3 TOP EDGE GREATER THAN 36 INCHES (914 MM) ABOVE THE FLOOR.
<br />7.4 ONE OR MORE WALKING SURFACES WITHIN 36 INCHES (914 MM) HORIZONTALLY OF THE
<br />GLAZING.
<br />8. ALL GLAZING IN RAILINGS REGARDLESS OF AN AREA OR HEIGHT ABOVE WALKING SURFACE. INCLUDED ARE STRUCTURAL
<br />BALUSTER PANELS AND NONSTRUCTURAL IN FILL -PANELS.
<br />9. GLAZING IN WALLS AND FENCES ENCLOSING INDOOR AND OUTDOOR SWIMMING POOLS, HOT TUBS AND SPAS WHERE THE
<br />BOTTOM EDGE OF THE GLAZING IS LESS THAN 60 INCHES (1524 MM) ABOVE A WALKING SURFACE AND WITHIN 60 INCHES
<br />(1524 MM) HORIZONTALLY OF THE WATER�S EDGE, THIS SHALL APPLY TO SINGLE GLAZING AND ALL PANES IN MULTIPLE
<br />GLAZING.
<br />10. GLAZING ADJACENT TO STAIRWAYS, LANDINGS, AND RAMPS WITHIN 36 INCHES (914 MM) HORIZONTALLY OF A WALKING
<br />SURFACE WHEN THE EXPOSED SURFACE OF THE GLASS IS LESS THAN 60 INCHES (1524 MM) ABOVE THE PLANE OF THE
<br />ADJACENT WALKING SURFACE.
<br />11. GLAZING ADJACENT TO STAIRWAYS WITHIN 60 INCHES (1524 MM) HORIZONTALLY OF THE BOTTOM TREAD OF A STAIRWAY IN
<br />ANY DIRECTION WHEN THE EXPOSED SURFACE OF THE GLASS IS LESS THAN 60 INCHES (1524 MM) ABOVE THE NOSE OF
<br />THE TREAD.
<br />EXCEPTION: THE FOLLOWING PRODUCTS, MATERIALS AND USES ARE EXEMPT FROM THE ABOVE HAZARDOUS LOCATIONS:
<br />1. OPENINGS IN DOORS THROUGH WHICH A 3-INCH(76 MM) SPHERE IS UNABLE TO PASS.
<br />2. DECORATIVE GLASS IN ITEMS 1, 6 OR 7�
<br />3. GLAZING IN SECTION R308.4.2, ITEM 2-EXCEPTIONS, WHEN THERE ISAN INTERVENING WALL OR OTHER PERMANENT
<br />BARRIER BETWEEN THE DOOR AND THE GLAZING.
<br />4. GLAZING IN SECTION R 308.4.2, ITEM 3, WHERE ACCESS THROUGH THE DOOR IS TO A CLOSET OR STORAGE AREA 3 FEET
<br />(914 MM) OR LESS IN DEPTH, GLAZING IN THESE APPLICATIONS SHALL COMPANY WITH SECTION R308.4.3.
<br />5. GLAZING IN SECTION R308.4.3, ITEM 2-EXCEPTIONS, WHEN A PROTECTIVE BAR IS INSTALLED ON THESE ACCESSIBLE
<br />SIDE(S) OF THE GLAZING 36 INCHES ± 2 INCHES (914 ± MM 51 MM) ABOVE THE FLOOR. THE BAR SHALL BE CAPABLE OF
<br />WITHSTANDING A HORIZONTAL LOAD OF 50 POUNDS PER LINEAR FOOT KG/M) WITHOUT CONTACTING THE GLASS AND BE A
<br />MINIMUM OF 1 Y2 INCHES (38 MM) IN CROSS SECTIONAL HEIGHT,
<br />6. OUTBOARD PANES IN INSULATING GLASS UNITS AND OTHER MULTIPLE GLAZED PANELS IN SECTION R308.4.3, ITEM
<br />3-EXCEPTIONS, WHEN THE BOTTOM EDGE OF THE GLASS IS 25 FEET (7620 MM) OR MORE ABOVE GRADE, A ROOF, WALKING
<br />SURFACES, OR OTHER HORIZONTAL [WITHIN 45 DEGREES (0.79 RAID) OF HORIZONTAL] SURFACE ADJACENT TO THE GLASS
<br />EXTERIOR.
<br />7. MIRRORS AND OTHER GLASS PANELS MOUNTED OR HUNG ON A SURFACE THAT PROVIDES A CONTINUOUS BACKING
<br />SUPPORT.
<br />8. SAFETY GLAZING IN SECTION R308.4, IS NOT REQUIRED WHERE:
<br />8.1 THE SIDE OF STAIRWAY, LANDING OR RAMP HASA GUARDRAIL OR HANDRAIL, INCLUDING BALUSTERS OR IN -FILL
<br />PANELS, COMPLYING WITH THE PREVISIONS OF; AND
<br />8.2 THE PLANE OF THE GLASS IS GREATER THEN 18 INCHES (457 MM) FROM THE RAILING.
<br />SPECIFICATIONS
<br />1. CONSTRUCTION:
<br />1. 1. 1.
<br />ACI 318-14 BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE
<br />ACI 530-13, ASCE 5/TMS 402-16 & ACI 530.1-13, ASCE 6/TMS 602-16
<br />SPECIFICATIONS FOR MASONRY STRUCTURES.
<br />1.1.3.
<br />ASTM C270-14A, C90-14 & C91-05 SPECIFICATIONS FOR MASONRY STRUCTURES
<br />1.1.4.
<br />NATIONAL DESIGN SPECIFICATIONS (NDS) FOR WOOD CONSTRUCTION, 2018 EDITION, AND ALL
<br />ACCOMPANYING SUPPLEMENTS.
<br />1.1.5.
<br />FLORIDA BUILDING CODE 7TH EDITION (2020) RESIDENTIAL
<br />1.1.6.
<br />"MANUAL OF STEEL CONSTRUCTION, ALLOWABLE STRESS DESIGN", BY THE AMERICAN
<br />INSTITUTE OF STEEL CONSTRUCTION, (AISC) 15TH EDITION.
<br />1.1.7.
<br />"DESIGN SPECIFICATION FOR LIGHT METAL PLATE CONNECTED WOOD TRUSSES" BY THE
<br />TRUSS PLATE INSTITUTE TR11-14.
<br />1.2.
<br />DESIGN:
<br />1.2.1.
<br />ACI 301-16 BUILDING CODE REQUIREMENTS FOR STRUCTURAL CONCRETE
<br />1.2.2.
<br />ACI 530-16, ASCE 5/TMS 402-16 & ACI 530.1-16, ASCE 6/TMS 602-16 SPECIFICATIONS FOR MASONRY STRUCTURES.
<br />1.2.3.
<br />ASTM C270-14A, C90-14 & C91-05 SPECIFICATIONS FOR MASONRY STRUCTURES
<br />1.2.4.
<br />NATIONAL DESIGN SPECIFICATIONS (NDS) FOR WOOD CONSTRUCTION, 2018 EDITION, AND ALL
<br />ACCOMPANYING SUPPLEMENTS.
<br />1.2.5.
<br />PLYWOOD DESIGN SPECIFICATIONS (APA)
<br />1.2.6.
<br />FLORIDA BUILDING CODE (FBC) 7TH EDITION (2020) AND FLORIDA BUILDING CODE 7TH EDITION RESIDENTIAL
<br />(FBCR)
<br />1.3.
<br />SHOP DRAWINGS:
<br />1.3.1.
<br />THERE SHALL NOT BE ANY DEVIATIONS FROM THESE DESIGN PLANS BY OTHERS
<br />DURING THE PREPARATION OF SHOP DRAWINGS WITHOUT WRITTEN APPROVAL FROM
<br />THE ENGINEER OF RECORD.
<br />1.3.2.
<br />ALL SHOP DRAWINGS ARE TO BE SUBMITTED TO THE ENGINEER OF RECORD PRIOR TO
<br />THE COMMENCEMENT OF CONSTRUCTION.
<br />1.3.3.
<br />ALL ROOF AND FLOOR TRUSS SHOP DRAWINGS ARE TO BE SIGNED AND SEALED BY A
<br />FLA. REG. PE. AND SHALL INCLUDE: DRAWINGS AND CALCULATIONS, REACTIONS AND
<br />BEARING POINTS, BRACING REQUIREMENTS, AND CONNECTIONS TO
<br />SUPPORTING TRUSS MEMBERS.
<br />2. DESIGN
<br />LOADS
<br />2.1.
<br />DEAD LOADS:
<br />2.1.1.
<br />UNIT WEIGHT OF SOIL, COMPACTED: 120 PCF
<br />2.1.2.
<br />UNIT WEIGHT OF REINFORCED CONCRETE: 150 PCF
<br />2.1.3.
<br />UNIT WEIGHT OF 8" C.M.U. BLOCK: 55 PSF
<br />2.1.4.
<br />1ST FLOOR SUPERIMPOSED LOAD: 20 PSF
<br />2.1.5.
<br />UNIT WEIGHT OF 2x4 PARTITION WALLS: 11 PSF
<br />2.1.6.
<br />UNIT WEIGHT OF 2x6 BEARING WALLS: 12 PSF
<br />2.1.7.
<br />BALCONIES & DECKS: 15 PSF
<br />2.1.8.
<br />TILE ROOF
<br />TOPCHORD: 15 PSF
<br />BOTTOM CHORD: 10 PSF
<br />2.1.9.
<br />SHINGLE ROOF
<br />TOPCHORD: 7 PSF
<br />BOTTOM CHORD: 1OPSF
<br />2.1.10.
<br />FLOOR TRUSSES 15
<br />2.2.
<br />LIVE LOADS:
<br />2.Z 1.
<br />SIDEWALK AND DRIVEWAY LOAD: 250 PSF
<br />2,2.2.
<br />GARAGELOADS: 40 PSF
<br />2.2.3.
<br />PARTITIONED ROOMS: 40 PSF
<br />2.2.4.
<br />BALCONY AND DECKS: 60 PSF-UNDER 100 sq. ft.
<br />2.2.5.
<br />STAIRWAYS AND LANDINGS: 40 PSF
<br />2.2.6.
<br />SLEEPING ROOMS: 30 PSF
<br />2.2.7.
<br />FLOOR TRUSS
<br />TOP CHORD MINIMUM: 40 PSF
<br />2.2.8.
<br />ROOFTRUSS
<br />TOP CHORD MINIMUM: 20 PSF
<br />BOTTOM CHORD (ATTIC W/O LIMITED STORAGE): 10 PSF (NON -CONCURRENT)
<br />BOTTOM CHORD (ATTIC W/ LIMITED STORAGE): 20 PSF
<br />2.3.
<br />RAILING LOADS:
<br />2.3.1.
<br />ALL RAILING AND GUARD RAIL SYSTEM'S ARE TO BE DESIGNED TO WITHSTAND A
<br />CONCENTRATED LOAD OF 200 POUNDS APPLIED AT ANY POINT AND IN ANY
<br />DIRECTION ON THE RAILING.
<br />2.3.2.
<br />ALL RAILING AND GUARD RAIL SYSTEM'S ARE TO BE DESIGNED TO WITHSTAND A
<br />HORIZONTAL LOAD OF 50 PLF ON THE GUARDRAIL AND A SIMULTANEOUS LOAD
<br />OF 100 PLF APPLIED VERTICALLY DOWNWARD AT THE TOP OF THE GUARDRAIL
<br />2.3.3.
<br />GUARDRAIL SYSTEM SHALL BE DESIGNED TO WITHSTAND 2001b CONCENTRATED
<br />HORIZONTAL LOAD APPLIED ON 1 SQ. FT. AT ANY POINT IN THE SYSTEM.
<br />2.3.4.
<br />2.3.1.,2,3.2 & 23.3. ARE NOT REQUIRED TO BE APPLIED SIMULTANEOUSLY, BUT EACH
<br />SHALL BE APPLIED TO PRODUCE THE MAXIMUM STRESSES IN THE MEMBER COMPONENTS.
<br />2.4.
<br />WIND LOADS:
<br />2.4.1.
<br />WIND DESIGN TO BE CONDUCTED IN ACCORDANCE WITH SECT. R301.2 OF THE FLORIDA BUILDING
<br />CODE 7TH EDITION (2020) RESIDENTIAL, AND CONDUCTED BASED ON A 140MPH 3SECONDGUST,
<br />EXPOSURE "C", IMPORTANCE FACTOR "I" = 1.0. ENCLOSED BUILDING
<br />2.4.2.
<br />NET UPLIFT DEAD LOADS - 10 PSF SHINGLE, 15 PSF TILE
<br />2.4.3.
<br />WIND LOAD DETERMINATION BASED ON ASCE/SEI 7-16
<br />2.5.
<br />DEFLECTIONS:
<br />2.6.1. FLOOR TRUSSES SHALL LIMIT DEFLECTION TO U480TIMES THE SPAN FOR LIVE LOADS AND L/240 TIMES
<br />THE SPAN FOR TOTAL LOAD.
<br />3. DESIGN METHOD
<br />3.1. LOAD FACTOR DESIGN:
<br />3.1.1. THE LOAD FACTOR DESIGN METHOD WAS USED TO DESIGN:
<br />CAST -IN -PLACE CONCRETE SLABS AND FOOTINGS
<br />3.2. SERVICE LOAD DESIGN:
<br />3.2.1. THE SERVICE LOAD DESIGN METHOD WAS USED TO DESIGN:
<br />MASONRY WALLS AND LINTELS
<br />INTERIOR AND EXTERIOR WOOD FRAMING AND SHEATHING
<br />STAIRS AND FLOOR FRAMING
<br />ROOF FRAMING, SHEATHING AND UPLIFT
<br />3.3. LOAD COMBINATIONS FOR LRFD DESIGNS:
<br />3.3.1.
<br />THE FOLLOWING LOAD COMBINATIONS WERE DESIGNED FOR:
<br />TOTAL DL + FLOOR LL + ROOF LL
<br />TOTAL DL + FLOOR LL + WL
<br />TOTAL DL + WL
<br />3.3.2.
<br />ALL ROOF AND FLOOR TRUSSES SHALL BE DESIGNED TO RESIST THE WORST LOAD
<br />COMBINATION RESULTING IN THE MAXIMUM STRESSES PLACED ON THAT COMPONENT,
<br />BOTH PARTIAL, FULL, AND ALTERNATING SPAN LOADING ARE TO BE CONSIDERED,
<br />3.4.
<br />DESIGN ASSUMPTIONS:
<br />3.4.1.
<br />ALL FOUNDATIONS ARE CENTERED UNDER SUPPORTED COLUMNS AND WALLS UNLESS
<br />SHOWN OTHERWISE IN THE DESIGN PLANS.
<br />4. MATERIALS
<br />4.1.
<br />REINFORCING STEEL:
<br />4.1.1.
<br />REINFORCING STEEL SHALL BE ASTM A615 I A615M-12 MIN, GRADE 40, fy = 40 Ksi
<br />4.1.2.
<br />LAP SPLICE SHALL BE AS FOLLOWS: #5 BAR 25", #4 BAR 20", #3 BAR 20".
<br />4,1.3.
<br />ALL DIMENSIONS PERTAINING TO THE LOCATION OF REINFORCING ARE TO THE
<br />CENTERLINE OF EACH BAR EXCEPT WHERE THE COVER DIMENSION IS SHOWN TO THE
<br />FACE OF THE CONCRETE.
<br />4.1.4.
<br />REINFORCING DETAIL DIMENSIONS ARE OUT TO OUT OF BARS.
<br />4.1.5.
<br />REINFORCING MECHANICAL COUPLERS ARE TO DEVELOP 125 % OF THE REQUIRED
<br />YIELD STRENGTH OF THE BAR AND ARE TO BE APPROVED BY THE ENGINEER OF
<br />RECORD.
<br />4.1.6.
<br />DESIGN COVER REQUIREMENTS:
<br />C-I-P CONCRETE FORMED AGAINST EARTH:
<br />C-I-P CONCRETE EXPOSED TO EXTERIOR:
<br />C-I-P CONCRETE NOT EXPOSED:
<br />GROUT FILLED MASONRY:
<br />4.1.7.
<br />WELDED WIRE FABRIC (WWF): ASTMA-1851A185M-14
<br />4.1.8.
<br />DETAIL REINFORCEMENT IN ACCORDANCE WITH ACI 318-14 (STRUCTURAL CONCRETE)
<br />ACI 530-16 (MASONRY STRUCTURES)
<br />4.2.
<br />CONCRETE:
<br />4.2,1.
<br />3"
<br />2"
<br />i yi,
<br />Y4"
<br />CONCRETE TYPE
<br />MIN. 28 DAY
<br />DESIGN (fc)
<br />MODULES OF
<br />ELASTICITY
<br />DESIGN (E)
<br />C-I-P CONCRETE (NORMAL WEIGHT)
<br />2,500 Psi
<br />2,850 Ksi
<br />C-I-P CONCRETE (NORMAL WEIGHT) HERNANDO CO. ONLY
<br />3,000 Psi
<br />3,122 Ksi
<br />C-I-P GROUT
<br />3,122 Ksi
<br />4.2.2.
<br />CONCRETE SHALL CONSIST OF 1" MAXIMUM AGGREGATE CONCRETE MIX WITH SLUMP
<br />BETWEEN 6" AND 7" AT TIME OF PLACEMENT. SEE SPECIFICATIONS FOR ADDITIONAL
<br />CRITERIA.
<br />4.2.3.
<br />GROUT SHALL CONSIST OF PEA ROCK (318" MAXIMUM AGGREGATE) CONCRETE MIX
<br />WITH SLUMP BETWEEN 8" AND 10" AT TIME OF PLACEMENT, SEE SPECIFICATIONS FOR
<br />ADDITIONAL CRITERIA.
<br />4.2.4.
<br />CONSTRUCTION JOINTS WILL BE PERMITTED
<br />4.2.5.
<br />METHOD OF CONCRETE FORMING, PLACEMENT AND CURING SHALL BE CONDUCTED IN
<br />ACCORDANCE WITH THE SPECIFICATIONS AS STATED.
<br />4.2.6.
<br />EARTH SUPPORTED SLABS (EXCLUDING EXTERIOR WALKWAYS & DRIVEWAYS):
<br />3 1/2" MIN. THICKNESS W1 MIN. REINFORCEMENT OF 6.0 x 6.0 W/ 1.4 x 1.4 WWF @
<br />MID -DEPTH OF SLAB. FIBER MESH PER DESIGN MIX MAY BE USED I.L.O. WWF @
<br />CONTRACTORS DISCRETION.
<br />4.3. CONCRETE MASONRY:
<br />4.3.1.
<br />FILLED CELLS W1 (1) #5 BAR SHALL BE LOCATED PER PLAN.
<br />4.3.2.
<br />LOAD BEARING CONCRETE MASONRY BLOCK SHALL BE ASTM C90-14, TYPE 11
<br />NON -MOISTURE CONTROLLED.
<br />4.3.3.
<br />ALL CELLS & CAVITIES BELOW GRADE WILL BE FILLED W1 CONCRETE IN ALL
<br />STEM WALLS.
<br />4.3.4.
<br />THE AGGREGATE STRENGTH OF THE BLOCK AND MORTAR SHALL BE F'm = 2,000 PSI
<br />MINIMUM.
<br />4.3.5.
<br />METHOD OF CONCRETE MASONRY PLACEMENT AND CONSTRUCTION SHALL BE
<br />CONDUCTED IN ACCORDANCE WITH THE SPECIFICATIONS AS STATED.
<br />4.3.6.
<br />MORTAR SHALL BE ASTM C270 TYPE "S" FOR ALL MASONRY CONSTRUCTION.
<br />4.4. STRUCTURAL LUMBER:
<br />4.4.1.1.
<br />INTERIOR LOAD BEARING WALLS SPF #2
<br />ALL EXTERIOR FRAMING SPF #2
<br />4.4.1.2.
<br />ALL FRAME WALLS TO BE CONSTRUCTED USING SPF #2, STUD QUALITY OR BETTER
<br />4.4.1.2.1
<br />ALL HEADER, BEAMS, COLUMNS ETC. TO BE SYP #2 OR BETTER
<br />4.4.2.
<br />ALL PLYWOOD USED FOR EXTERIOR APPLICATIONS SHALL BE APA RATED STRUCTURAL
<br />SHEATHING 15/32" EXP 1 OR 7/16" STRUCTURAL 1, U.N.O.
<br />4.4.3.
<br />ALL PLYWOOD USED FOR INTERIOR APPLICATIONS SUCH AS SUB FLOORING AND
<br />SHEAR WALLS SHALL BE APA RATED SHEATHING EXP 1 U.N.O.
<br />4.4.4.
<br />IF OSB BOARD IS TO BE USED IN PLACE OF PLYWOOD IS TO HAVE SIMILAR OR
<br />GREATER SECTION PROPERTIES.
<br />4.4.5.
<br />ONLY STRUCTURAL LUMBER TO BE USED FOR AN EXTERIOR APPLICATION. WOOD IN
<br />CONTACT WITH CONCRETE IS TO RECEIVE A STANDARD GRADE PRESSURE TREATING.
<br />4.4.6.
<br />WHEN PRE ENGINEERED TRUSSES ARE CALLED FOR ON THE PLANS THE
<br />MANUFACTURER IS TO SUBMIT SHOP DRAWINGS TO THE ENGINEER OF RECORD.
<br />4.4.7.
<br />DESIGN, FABRICATE AND ERECT WOOD TRUSSES IN ACCORDANCE WITH THE "DESIGN
<br />SPECIFICATION FOR LIGHT METAL PLATE CONNECTED WOOD TRUSSES" BY THE
<br />ANSI/TPI 1-2014, 8CSI
<br />4.4.8.
<br />UNTREATED WOOD SHALL NOT BE IN DIRECT CONTACT WITH CONCRETE. SEAT PLATES
<br />SHALL BE PROVIDED AT BEARING LOCATIONS WITHOUT WOODEN TOP PLATES.
<br />4.4.9.
<br />ALL EXTERIOR FRAME WALLS SHALL BE STUCCO FINISH- 7/8" STUCCO FINISH PER
<br />ASTM C. 926, APPLY 3 LAYERS W1 TOTAL THICKNESS 7/8" OVER METAL LATH. FIRST
<br />2 LAYERS 3/8" THICK EACH. 3RD LAYER 118" THICK
<br />4.4.10.
<br />INSTALLATION OF EXTERIOR LATHING & FRAMING SHALL COMPLY TO ASTM C 1063
<br />PER FLORIDA CODE R703.7
<br />4.5. FASTENERS AND TIE DOWNS:
<br />T5. 1.
<br />FASTENERS AND TIE DOWNS SHALL CO'�S_IST OF BUT ARE NOT LIMITED TO:
<br />SHAPES, ANGLES, CHANNELS: ASTM A36/36M 05 Fy = 36 Ksi
<br />ROUND METAL PIPE: ASTM A53, GRADE B Fy = 35 Ksi
<br />SQUARE METAL TUBING: ASTM A500, GRADE B Fy = 46Ks!
<br />HIGH STRENGTH BOLTS: ASTM A325
<br />MACHINE BOLTS: GALVANIZED ASTIM A307
<br />4.5.2.
<br />SHEET METAL ACCESSORIES SHALL CONFORM TO: Fy = 33KsiWITH G90
<br />GALVANIZED COATING IN ACCORDANCE WITH ASTM A525-87.
<br />4.5.3.
<br />NAILS SHALL CONSIST OF: COMMON WIRE NAILS WITH MINIMUM DIAMETER AS
<br />FOLLOWS: 8d = 0.131", 10d = 0.148", 12d = 0.148", 16d = 0.162".
<br />4.5.4.
<br />ALL FASTENERS AND TIE DOWNS EMBEDDED IN CONCRETE OR USED IN AN EXTERIOR
<br />APPLICATION ARE TO RECEIVE AN ANTI -CORROSIVE COATING BY MANUFACTURER
<br />PRIOR TO INSTALLATION.
<br />4.5.5.
<br />ALL FASTENERS AND TIE DOWNS ARE TO PROVIDE THE UPLIFT CAPACITY CALLED
<br />FOR IN THE PLANS ARE A MINIMUM.
<br />4.5.6.
<br />ALL FASTENER TIE DOWNS, BEAM HANGERS, JOIST HANGERS, AND FLOOR TRUSS
<br />STRAPPING ARE TO BE INSTALLED IN ACCORDANCE WITH THE PLANS AND
<br />SPECIFICATIONS.
<br />4.5.7.
<br />CONCRETE EMBEDDED'TBOLTS USED FOR UPLIFT ARE TO BE WET SET PRIOR TO
<br />INITIAL SET OF THE CONCRETE, SPACING AND ALIGNMENT ARE TO BE IN ACCORDANCE
<br />WITH THE DESIGN PLANS, U.N.O. ALTERNATES TO "J" BOLTS ARE NOTED ON PLANS.
<br />4.5.8.
<br />CONCRETE EMBEDDED TIE DOWNS USED FOR TRUSS AND WALL UPLIFT ARE To BE
<br />PLACED AROUND EMBEDDED REINFORCING PRIOR TO OR WHILE PLACING GROUT.
<br />4.6. MICRO -LAM
<br />LUMBER:
<br />4.6.1.
<br />MICRO -LAM STRESS GRADES SHALL PROVIDE THE FOLLOWING MINIMUM PROPERTIES:
<br />E 2,000,000 PSI
<br />Fb 2,950 PSI
<br />Ft 1,850 PSI
<br />Fc 500 PSI (PERPENDICULAR)
<br />Fc= 2,700 (PARALLEL)
<br />4.7. STEEL:
<br />Fv = 285 PSI
<br />4.7.1.
<br />INSTALLATION OF ALL STEEL TO BE PERFORMED BYAN EXPERIENCED, QUALIFIED
<br />STEEL ERECTOR.
<br />4.7.2.
<br />FABRICATE AND ERECT ALL STRUCTURAL STEEL IN ACCORDANCE WITH A.I.S.C.
<br />'SPECIFICATION FOR THE DESIGN, FABRICATION, AND ERECTION OF STRUCTURAL
<br />STEEL FOR BUILDINGS".
<br />4.7.3.
<br />STRUCTURAL STEEL: ASTM A36/36M 05.
<br />4.7.4.
<br />STEEL TUBING: ASTM A500, GRADE B.
<br />4.7.5.
<br />WELDED CONNECTIONS: E70XX ELECTRODES, MINIMUM SIZE FILLET WELDS 3/16", AWS
<br />CERTIFIED WELDERS. CERTIFICATION PAPERS TO BE SUBMITTED UPON REQUEST.
<br />4.7.6.
<br />WHERE STEEL BEAMS ARE CONTINUOUS OVER COLUMNS, PROVIDE WEB STIFFENER
<br />PLATES ON EACH SIDE OF THE WEB, OF A THICKNESS EQUAL TO BEAM FLANGE
<br />THICKNESS, LOCATED AT THE CENTER LINE OF THE TUBE COLUMN.
<br />4.7.7.
<br />THE STEEL FRAME IS "NON -SELF SUPPORTING". ADEQUATE TEMPORARY SUPPORT
<br />SHALL BE PROVIDED BY THE CONTRACTOR UNTIL REQUIRED CONNECTIONS OR
<br />4.8. SOIL
<br />ELEMENTS ARE IN PLACE.
<br />4.8.1.
<br />MINIMUM SOIL BEARING PRESSURE CAPACITY OF 2,000 PSF.
<br />FOUNDATIONS HAVE BEEN DESIGNED WITH THE MIN. CAPACITY OF 2,000 PSF
<br />4.8.2.
<br />ALL SOIL IS TO BE CLEAN & POISONED FOR TERMITES PER FLORIDA BUILDING CODE 7TH EDITION (2020)
<br />RESIDENTIAL SECTION R318.
<br />4.8.3.
<br />SOIL IS TO BE COMPACTED TO 95% MODIFIED PROCTOR AS DEFINED BY ASTM D 1557-02EO1
<br />TERMITE PROTECTION -
<br />CONTRACTOR TO USE (1) OF THE TREATMENTS BELOW
<br />Borate / Boracore treated lumber
<br />Soil Chemical Barrier Method
<br />Other treatment - Must specify proposed method and submit documentation, which
<br />substantiates the proposed method, is an approved termite protection system or method.
<br />OR CHEMICAL SOIL TERMITE TREATMENT IS USED
<br />1 FBC-R R318.1 - "A permanent sign which identifies the termite treatment provider
<br />and need for re -inspection and treatment contract renewal shali,be provided.
<br />The sign shall be posted near the water heater or electric panel'
<br />2. Condensate and roof downspouts shall discharge at least
<br />V-10" away from the building side walls.
<br />3. 1 rrigation/s
<br />grinkler systems including all risers and
<br />-0" of the building side wall.
<br />spray hea s shall not be installed within 1'
<br />4. FBC-R R318.7- To provide for inspection for termite infestation, between
<br />wall covering and final earth grade shall not be less than 6 inches.
<br />Exception: Paint or decorative cementitious finish less than 5/8"
<br />thick adhered directly to the foundation wall.
<br />5. FBC-R R318.1.1 - Initial treatment shall be done after all excavation
<br />and backfill is complete.
<br />6. FBC-R R318.1.2 - Soil disturbed after the initial treatment shall be retreated
<br />including spaces boxed or formed.
<br />7. FBC-R R318.1.3 - Boxed areas in concrete floors for subse
<br />purent installation of tra
<br />etc., shall be made with permanent metal or plastic forms. e manent forms must
<br />of a size and depth that will eliminate the disturbance of soil after the initial treatment.
<br />8. FBC-R R318.1.4 - Minimum 6 mil vapor retarder must be installed to protect against
<br />rainfall dilution, If rainfall occurs bef6re vapor retarder placement,
<br />retreatment is required.
<br />9. FBC-R R318.1.5 - Cgcrete overpouf and mortar along the foundation perimeter
<br />must be removed be ore exterior soi treatment.
<br />10. FBC-R R318.1.6 - Soil treatment must be applied under all exterior concrete
<br />or grade within V-0" of the structure sidewalls.
<br />11. FBC-R R318.1.6 - An exterior vertical chemical barrier must be installed after
<br />construction is complete, including landscaping and irrigation, Any soil disturbed
<br />after the vertical barrier is applied, shall be retreated,
<br />12. FBC-R R318.1 - All buildings are required to have pre -construction treatment.
<br />13. FBC-R R318.1 - A certificate of compliance must be issued to the building department
<br />b a, licensed pest control company before a certificate of o, U issued,
<br />T�e certificate of compliance shall state: "The building has rec�ived`a complete
<br />treatment for the prevention of subterranean termites. The treatment is in
<br />accordance with the rules and laws of the Florida Department of Agriculture
<br />and Consumer Services".
<br />14. FBC-R R318.6 - After all work is completed, loose wood and fill must be removed
<br />from below and within V-0" of the building. This includes all grade stakes,
<br />tub trap boxes, forms, shoring or other cellulose containing material.
<br />BUILDING DATA WIND SPEED (ULTIMATE) 140 MPH
<br />WIND SPEED (ALLOWABLE) 108 MPH
<br />WIND EXPOSURE -- "C" FBC-R 7TH EDITION (2020) R301.2.1.1
<br />INTERNAL PRESSURE COEFFICIENT= 0.18 ENCLOSED BLDG)
<br />BUILDING CATEGORY = 11
<br />DESIGN WIND PRESSURE:
<br />(COMPONENT AND CLADDING) WORSTCASE (10 SF - END ZONE)
<br /># END ZONE IS ONLY WITHIN 4'-0"
<br />OF ALL EXTERIOR BUILDING CORNERS
<br />INDOWS AND DOORS
<br />CONSTRUCTION 140 MPH + 29.7 PSF / -32.2 PSF (INTERIOR) U.N.C..
<br />TYPE: 5B + 29.7 PSF / -39.7 PSF (END) U.N.0
<br />GARAGE DOORS (V = 140 MPH)
<br />SINGLE 9x7 +26.1 PSF / -29.9 PSF
<br />DOUBLE 160 +24.9 PSF / -28.0 PSF
<br />SOFFIT +29.7 PSF / -39.7 PSF
<br />NOTE: THE WIND PRESSURES LISTED ABOVE ARE ALLOWABLE PRESSURES.
<br />NOTE:
<br />IT IS THE CONTRACTORS RESPONSIBILITY TO REVIEW ALL DRAWINGS BEFORE
<br />CONSTRUCTION BEGINS. FLORIDA DESIGN SOLUTIONS, INC. IS RESPONSIBLE FOR THE
<br />STRUCTURAL INTEGRITY OF THIS PROJECT ONLY, ANY DISCREPANCY BETWEEN FIELD
<br />CONDITIONS, OTHER DESIGN PROFESSIONALS'SHOP DRAWINGS, CONTRACTORS'
<br />BUILDING METHODS, AND THESE SIGNED AND SEALED DRAWINGS MUST BE BROUGHT TO
<br />THE ATTENTION OF FLORIDA DESIGN SOLUTIONS, INC. PRIOR TO THE COMMENCEMENT OF
<br />CONSTRUCTION.
<br />NOTE:
<br />GYPSUM BOARD MAY BE INSTALLED USING GWB54 NAILS TO SET IN PLACE. FIELD
<br />FASTENING SHOULD BE TYPE "W" 1Y4" DRYWALL SCREWS AT 12" O.C. FOR CEILINGS AND ly8,,
<br />DRYWALL SCREWS AT 12" O.C. FOR WALLS. ALL ENDS AND EDGES OF WALLBOARD SHALL
<br />OCCUR OVER AND BE SCREWED TO SUPPORTS. MAXIMUM SCREW SPACING AT ENDS
<br />(EDGES IN VERTICAL APPLICATION) SHALL BE 6" O.C. AT EACH SUPPORT. MINIMUM SCREW
<br />NAIL DISTANCE FROM EDGE SHALL BE Y8". THIS SHALL APPLY TO BOTH CEILING AND WALL
<br />INSTALLATION. DRYWALL SHIMS SHALL BE USED ONLY WHERE NECESSARY. OPENINGS
<br />CUT FOR OUTLETS, SWITCHES, ETC, SHALL BE OF A TOLERANCE THAT CAN BE COVERED
<br />ADEQUATELY WITH NORMAL SWITCH PLATES AND COVERS WITHOUT ADDITIONAL TAPING
<br />OR CAULKING. DRYWALL SHALL NOT BE INSTALLED WITHOUT PROPER BACKING.
<br />NOTE:
<br />ALL HEADERS, BEAMS, ETC ARE TO BE SYP #2 OR BETTER AND OR MICROLAM
<br />AS INDICATED ON THE DRAWINGS AND CAN NOT BE REVISED.
<br />C=
<br />cm
<br />C=
<br />C-4
<br />LL.
<br />C�4
<br />C= crj
<br />CL,
<br />co
<br />C=
<br />C5
<br />\0
<br />*%
<br />< j
<br />FL
<br />JA,
<br />V a 10
<br />To the best ofthe Engineers knowledge, information and belief,
<br />the structural
<br />plans and specifications contained within these
<br />drawings comply with the 2020
<br />Florida Building Code -
<br />Residential
<br />7th Edition. Engineers signature and seal is only for
<br />the structural
<br />engineering portions of the drawing pages bearing
<br />Engineers
<br />signature and seal.
<br />E
<br />C:) 8
<br />0
<br />6
<br />t- - 0-1.0
<br />u`1 rZ :R
<br />C14 0 46
<br />U_ LL Lu
<br />Z
<br />CL
<br />Co C
<br />0
<br />co
<br />2 ()) X0
<br />W
<br />Z
<br />co
<br />Tr) Z� 0
<br />C) Z
<br />Z
<br />C14
<br />W
<br />CIE]
<br />loql
<br />C1
<br />-2
<br />j
<br />0
<br />Ln
<br />V)
<br />Uj
<br />'5
<br />Mal
<br />LML,
<br />u C/)
<br />CD
<br />CD
<br />c6 E
<br />E '0
<br />< R
<br />CD-
<br />E
<br />-
<br />Q
<br />0
<br />0
<br />U 0
<br />0
<br />C-:, E
<br />Z 8
<br />< 0
<br /><
<br />2
<br />� Z
<br />::3 M
<br />C/) C:
<br />0
<br />I ,
<br />0
<br />Z
<br />Z
<br />Cn
<br />co
<br />2
<br /><
<br />1
<br />0 <
<br />Z
<br />0
<br />CL 3:
<br />�0
<br />MO
<br />CD
<br />N
<br />0
<br />2 C:)
<br />a, (.0
<br />>
<br />LO
<br />LO
<br />E2
<br /><
<br />Co
<br />C:)
<br />co CY)
<br />N
<br />=3
<br />CY)
<br />U) 0
<br />M
<br />Co
<br />LO
<br />4_j
<br />4-1
<br />U)
<br />0
<br />(n N
<br />N
<br />co C:)
<br />C:)
<br />ILL N
<br />rl-
<br />a)
<br />Lo
<br /><
<br />0
<br />LO N
<br />T_
<br />E
<br />2_1
<br />.2 0
<br />6
<br />Z
<br />M
<br />Z
<br />=3
<br />E 04
<br />E
<br />0 0
<br />'a C11
<br />< 0 f
<br />(D
<br />_j
<br />JOB
<br />NO:
<br />22-12364
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />SN
<br />
|