|
DEMOLITION NOTES
<br />1 ALL DEMOLITION WORK SHALL BE PERFORMED WITH "DUE CARE & DILIGENCE" SO
<br />AS TO PREVENT THE ARBITRARY DESTRUCTION OR INTERRUPTION OF
<br />CONCEALED UTILITIES WHICH ARE INTENDED TO REMAIN IN USE AND THE
<br />ROUTING OF WHICH COULD NOT BE PREDETERMINED UNTIL DEMOLITION WAS
<br />STARTED. ALL SUCH DISCOVERIES OF UTILITIES DURING THE DEMOLITION
<br />PROCESS WHICH ARE IN A LOCATION DIFFERENT FROM THAT INDICATED, CHANGE
<br />DIRECTION FROM FLOOR TO FLOOR, ETC., OR ARE UNIDENTIFIED, SHALL BE
<br />REPORTED TO THE ARCHITECT BEFORE REMOVAL.
<br />2. OCCUPANTS AND PEDESTRIANS SHALL BE PROTECTED DURING CONSTRUCTION
<br />AND DEMOLITION ACTIVITIES PER CHAPTER 33 SAFEGUARDS DURING
<br />CONSTRUCTION IN THE IBC. REQUIRED EXITS, EXISTING STRUCTURAL ELEMENTS,
<br />FIRE PROTECTION DEVICES AND SANITARY SAFEGUARDS SHALL BE MAINTAINED
<br />AT ALL TIMES DURING ALTERATIONS, REPAIRS, AND ADDITIONS. WHERE SUCH
<br />REQUIRED ELEMENTS OR DEVICES ARE BEING ALTERED OR REPAIRED, ADEQUATE
<br />SUBSTITUTE PROVISIONS SHALL BE MADE BY THE CONTRACTOR.
<br />3. REMOVE ALL EXISTING CONSTRUCTION THAT WILL BE NECESSARY TO BE
<br />REMOVED TO ACCOMPLISH THE NEW WORK INDICATED. PRIOR TO THE REMOVAL
<br />OF ANY WALLS CONTRACTOR TO VERIFY WITH ARCHITECT/STRUCTURAL
<br />ENGINEER IF ANY WALLS ARE STRUCTURAL SUPPORTING. IF WALLS ARE
<br />STRUCTURAL SUPPORTING WALLS, CONTRACTOR TO RECEIVE FROM ARCHITECT
<br />STRUCTURAL ENGINEER PROCEDURES TO SHORE AND BRACE ANY REQUIRED
<br />STRUCTURAL ELEMENTS AND RECEIVE DETAILS FOR FINISHED CONDITION.
<br />4. REMOVE EXISTING MILLWORK AS INDICATED. FLOOR SURFACE SHALL BE PATCHED
<br />FLUSH TO MATCH ADJACENT SURFACES OR TO RECEIVE NEW FINISHES.
<br />5. WHERE INDICATED, REMOVE EXISTING DOOR AND FRAME AND SEAL OPENING
<br />WITH WALL CONSTRUCTION TO MATCH ADJACENT FINISHES UNLESS NOTED
<br />OTHERWISE. FINISH WALL TO MATCH ADJACENT FINISH OR TO RECEIVE NEW
<br />FINISH AS SCHEDULED.
<br />6. ALL STRUCTURAL SYSTEMS SHALL BE MAINTAINED AND SHALL BE OF SUFFICIENT
<br />STRENGTH TO SUPPORT THE DESIGN LOADS AND TO RESIST THE DEFORMATION
<br />CAUSED BY SUCH LOADS TO WHICH THE SOIL PRESSURE INCLUDING SURCHARGE,
<br />HYDROSTATIC HEAD, AND IMPACT LOADS AS APPLICABLE.
<br />7. PATCH ALL FINISHES TO MATCH EXISTING, INCLUDING BUT NOT LIMITED TO,
<br />GYPSUM BOARD, PLASTER, ACOUSTIC SYSTEMS, WOOD TRIM, BASE, PANELS,
<br />RAILS, AND WAINSCOT, ETC. VERIFY MATCH OF NEW FINISH MATERIALS TO
<br />EXISTING COLOR, TEXTURE, THICKNESS, CUT, ETC. TO SATISFACTION OF THE
<br />OWNER PRIOR TO INSTALLATION. PROVIDE OTHER MATERIALS TO MATCH
<br />EXISTING WHEN REQUIRED TO BE APPROVED BY THE OWNER.
<br />8. WHERE APPLICABLE LEVEL ALL EXISTING FLOORS AS REQUIRED TO RECEIVE NEW
<br />FLOOR FINISHES. INSTALL REQUIRED TRANSITION PIECES BETWEEN VARIOUS
<br />FLOOR FINISHES AS DETAILED ON THE DRAWINGS. MATCH EXISTING WHERE
<br />POSSIBLE.
<br />GENERAL ALTERATION NOTES:
<br />1 ALL EXISTING SUBSTRATES AND FINISHES DISTURBED OR INTERRUPTED BY THE
<br />WORK SHALL BE REPLACED OR"FILLED IN"TO ACHIEVE UNIFORM COLOR,
<br />TEXTURE, PATTERN, AND APPEARANCE TO MATCHING ADJACENT SUBSTRATES
<br />AND FINISHES. TRANSITION BETWEEN EXISTING TO EXISTING AND NEW TO
<br />EXISTING SUBSTRATES AND FINISHES SHALL BE ACHIEVED IN STRAIGHT
<br />HORIZONTAL AND/OR VERTICAL LINES BETWEEN DIFFERENT AND/OR NEW
<br />SUBSTRATES AND FINISHES.
<br />2. PATCH, REPAIR, OR REPLACE ALL EXISTING FINISHES AND SUBSTRATES
<br />DISTURBED DURING CONSTRUCTION OR AS A RESULT OF DEMOLITION OR
<br />REMOVAL OF AN ITEM. ALL REPAIR OR REPLACEMENT SHALL MATCH ADJACENT
<br />EXISTING AND/OR NEW SUBSTRATES, PATTERNS, AND FINISHES. SEE ROOM FINISH
<br />SCHEDULE AND SPECIFICATIONS FOR NEW FINISHES.
<br />3. PREPARE EXISTING REMAINING WORK SUBSTRATES TO RECEIVE NEW FINISHES
<br />AS INDICATED ON THE ROOM FINISH SCHEDULE AND IN SPECIFICATIONS.
<br />SUBSTRATE PREPARATION SHALL BE IN CONFORMANCE WITH THE INSTALLATION
<br />REQUIREMENTS OF EACH NEW FINISH.
<br />4. AT THE DEMOLITION OF AN EXISTING ITEM, REMOVE ALL TRACES OF THE
<br />DEMOLISHED ITEMS/COMPONENTS FROM THE SURFACE OF THE REMAINING
<br />FLOOR, WALLS, CEILING, AND ROOF. AT THE REMOVED FASTENERS IN ALL
<br />EXISTING MASONRY WALLS AND FLOORS, PATCH HOLE WITH GROUT LEVEL WITH
<br />EXISTING ADJACENT SUBSTRATES IN ORDER TO RECEIVE NEW FINISHES.
<br />5. AT EXISTING FLOORS: WHERE WALLS ARE SCHEDULED FOR DEMOLITION AND
<br />EXTEND TO BELOW THE CONTINUOUS FLOOR LINE, THE WALL SHALL BE
<br />DEMOLISHED TO BELOW THE FLOOR THICKNESS. PATCH JOINTS SHALL NOT
<br />TELEGRAPH THROUGH THE NEW FINISH.
<br />6. AT WALL SURFACES TO BE PAINTED, WHERE PATCHING OCCURS IN THE WORK OF
<br />AN EXISTING PAINTED SURFACE, THE PATCHED AREA SHALL BE SPACKLED,
<br />FILLED, PRIMED, AND INTERMEDIATE PAINT COATS APPLIED PRIOR TO
<br />APPLICATION OF FINAL FINISH PAINT COATS. APPLY FINAL FINISH PAINT COATS
<br />OVER THE ENTIRE WALL SURFACE CONTAINING THE PATCH. WHERE PAINTING IS
<br />LIMITED TO PATCH, THE WORK AREA SHALL INCLUDE THE SURFACE FROM THE
<br />JOINT AT THE WALUFLOOR INTERSECTION TO THE JOINT AT THE WALUSEALING
<br />INTERSECTION. IT SHALL EXTEND HORIZONTALLY FROM LEFT SIDE OF THE PATCH
<br />TO RIGHT SIDE OF THE PATCH AND SHALL INCLUDE THE ENTIRE PATCH. PROVIDE
<br />ADDITIONAL SPACKLING AND PAINT COATS UNTIL THE PATCH AREA IS BLEND
<br />COMPLETELY WITH THE EXISTING ADJACENT WALL SURFACE. PATCHES AT
<br />CEILINGS SHALL BE TREATED IN SAME FASHION AS DESCRIBED ABOVE.
<br />7. AT ALL CERAMIC TILE AREAS TO BE PATCHED/REPAIRED THE FOLLOWING WORK
<br />SHALL OCCUR AT DEMOLISHED ITEMS AND DAMAGED AREAS, FILL ALL HOLES IN
<br />EXISTING CERAMIC WALL AND FLOOR TILE THAT ARE UP TO 1 INCH IN DIAMETER
<br />WITH A COLOR EPDXY GROUT TO MATCH THE EXISTING CERAMIC TILE COLOR.
<br />REMOVE AND REPLACE EXISTING ADJACENT AROUND AREAS WHERE HOLES
<br />EXCEED ONE INCH IN DIAMETER. REPLACE WITH NEW TILES THAT MATCH AS
<br />CLOSELY AS POSSIBLE TO EXISTING TILES. MATCH PATTERN, SIZE, SHAPE, COLOR,
<br />TEXTURE, AND COMPOSITION. FINAL SELECTION OF TILE TO BE INSTALLED SHALL
<br />BE THE BY THE ARCHITECT AND OWNER'S REPRESENTATIVE.
<br />8. FOLLOWING ANY DEMOLITION AND/OR REMOVAL, PATCH AND REPAIR ALL
<br />EXISTING DISTURBED SUBSTRATES AND FINISHES TO MATCH EXISTING
<br />SUBSTRATES AND FINISHES OR PREPARE EXISTING ADJACENT CONSTRUCTION TO
<br />ACCOMMODATE NEW CONSTRUCTION AND SCHEDULE FINISHES.
<br />0)
<br />N
<br />0
<br />co
<br />r_
<br />0
<br />C 'D
<br />0 a.
<br />GENERAL NOTES:
<br />1 VERIFY ALL EXISTING CONDITIONS PRIOR TO BEGINNING WORK. BRING ANY DISCREPANCIES FROM
<br />THE DRAWING AND NOTES TO THE ARCHITECT IMMEDIATELY. MINOR CHANGES IN THE SCOPE OF
<br />THE DEMOLITION WORK SHALL NOT JUSTIFY AN ADDITIONAL COST.
<br />2. REMOVAL OF EXISTING FIXTURES AND EQUIPMENT WILL REQUIRE ISOLATING THE PIPING RISERS
<br />OR MAINS VIA SHUT-OFF VALVES. INSTALL NEW ISOLATION VALVES WERE REQUIRED FOR
<br />COMPLETION OF WORK.
<br />3. REMOVAL OF EXISTING PLUMBING FIXTURES AND EQUIPMENT, ETC. WILL REQUIRE CAPPING AND
<br />SEALING EXISTING MAINS OR BRANCHES AS NECESSARY AND REQUIRED TO ALLOW THE
<br />REMAINING SYSTEMS TO FULLY OPERATE WITHOUT DEGRADATION. CONTRACTOR SHALL PROVIDE
<br />PROTECTIVE PLASTIC DROP CLOTHS TO PROTECT THE EXISTING OCCUPIED AREAS AND
<br />EQUIPMENT FROM DUST AND DEBRIS DURING THE CONSTRUCTION WORK AND SHALL CLEAN THE
<br />AREAS OF ALL CONSTRUCTION DIRT DAILY, AND UPON COMPLETION OF THE WORK. REFER TO
<br />GENERAL CONDITIONS AND DIVISION-1 SECTIONS IN THE SPECIFICATIONS.
<br />4. ALL DRAINED PIPING RISERS AND MAINS SHALL BE REFILLED WITH PROPER FLUID AND PROPERLY
<br />VENTED BY THIS CONTRACTOR ONCE NEW WORK HAS BEEN INSTALLED.
<br />5. COORDINATE WITH GENERAL CONTRACTOR THE REMOVAL AND REPLACEMENT OF ALL EXISTING
<br />CEILINGS, WALLS ETC. AS REQUIRED FOR MECHANICAL DEMOLITION WORK.
<br />6. EXISTING PIPING AND EQUIPMENT, ETC. NOT TO BE UTILIZED IN THE COMPLETED BUILDING SHALL
<br />BE DISCONTINUED OR REMOVED AS REQUIRED. ALL ENDS OF DISCONTINUED PIPING SHALL BE
<br />CAPPED IN THE NEAREST WALL, CEILING, OR FLOOR SO THAT THEY ARE COMPLETELY
<br />CONCEALED. OPENINGS LEFT IN WALLS, CEILINGS, ETC. WHERE EQUIPMENT AND PIPE ETC. ARE
<br />REMOVED AND NOT REPLACED, SHALL BE PATCHED NEATLY WITH THE SIMILAR MATERIAL TO
<br />ADJACENT CONSTRUCTION.
<br />7. EXISTING PIPING, FIXTURES, AND EQUIPMENT THAT ARE NOT TO BE REUSED SHALL BE REMOVED
<br />AND SHALL REMAIN THE PROPERTY OF THE OWNER IF THEY WISH TO RETAIN OWNERSHIP OF
<br />SAME. IF NOT, EQUIPMENT SHALL BECOME THE PROPERTY OF THIS CONTRACTOR AND SHALL BE
<br />REMOVED FROM THE SITE AS SOON AS PRACTICAL AND DISPOSED OF AN ACCORDANCE WITH
<br />APPLICABLE LAWS AND REGULATIONS.
<br />8. ALL CUTTING AND CHANNELING OF EXISTING BUILDING SHALL BE ACCOMPLISHED IN A NEAT AND
<br />WORKMAN -LIKE MANNER WITHOUT REMOVAL OF EXCESS MATERIALS. THIS CONTRACTOR SHALL
<br />PATCH AND REPLACE WITH MATERIAL SIMILAR TO ADJACENT CONSTRUCTION.
<br />9. WHERE EXISTING PIPING AND EQUIPMENT, ETC. THAT ARE TO BE UTILIZED IN THE COMPLETED
<br />PROGRAM CONFLICT WITH NEW CONSTRUCTION AND THE REQUIRED DEMOLITION, THEY SHALL BE
<br />RELOCATED AND RECONNECTED TO MAINTAIN THE DESIRED SERVICE.
<br />10. PORTIONS OF EXISTING SYSTEMS MAY BE SHOWN FOR CLARITY EVEN THOUGH IT MAY NOT BE
<br />NECESSARY TO MODIFY OR REVISE THEM. ALL EXISTING SYSTEMS ARE SHOWN BASED ON
<br />ORIGINAL OR REMODEL BUILDING DRAWINGS. CONTRACTOR TO VERIFY ALL EXISTING
<br />CONDITIONS.
<br />ii. ALL WORK MUST BE COORDINATED AND SCHEDULED WITH THE OWNER AND OCCUPANTS OF THIS
<br />BUILDING SO AS TO PROVIDE THE LEAST AMOUNT OF DISRUPTION OF BUILDING ACTIVITIES AS
<br />POSSIBLE.
<br />12. ALL ACCESSIBLE ABANDONED PIPING AND DUCTWORK SHALL BE REMOVED AND PROPERLY
<br />DISPOSED OF.
<br />13. CONTRACTOR SHALL VERIFY EXISTING SITE AND BUILDING CONDITIONS AND DIMENSIONS IN THE
<br />FIELD PRIOR TO DEMOLITION ACTIVITIES AND WORK.
<br />14. CONTRACTOR SHALL NOTIFY ARCHITECT AND OWNER OF ANY POSSIBLE ASBESTOS OR LEAD -
<br />CONTAINING MATERIALS DISCOVERED BEFORE PROCEEDING WITH WORK.
<br />15. CONTRACTOR SHALL NOT SCALE DRAWINGS.
<br />16. CONTRACTOR SHALL PROVIDE ALL NECESSARY TEMPORARY SHORING, TEMPORARY BRACING,
<br />AND/OR TEMPORARY SUPPORTS AS REQUIRED TO MAINTAIN STRUCTURAL INTEGRITY OF EXISTING
<br />STRUCTURE TO REMAIN AND/OR EXISTING BUILDING ELEMENTS TO REMAIN.
<br />17. CONTRACTORS TO VERIFY THE EXACT LOCATION OF ALL EXISTING UTILITIES PRIOR TO
<br />DEMOLITION ACTIVITIES AND WORK.
<br />18. CONTRACTOR SHALL REMOVE TRASH AND DEBRIS REGULARLY AS NECESSARY TO ELIMINATE
<br />INTERFERENCE WITH ROADS, STREET, WALKS, AND ALL OTHER ADJACENT FACILITIES.
<br />19. CONTRACTOR SHELL REPAIR, REPLACE, OR PATCH EXISTING BUILDINGS, DRIVEWAYS, SIDEWALKS,
<br />CANOPIES, AND/OR PARKING AREAS DAMAGED, MODIFIED, AND/OR DISTURBED BY DEMOLITION
<br />WORK AT NO COST TO THE OWNER.
<br />20. ALL EXISTING EQUIPMENT THAT REMAINS SHALL BE PROTECTED DURING DEMOLITION AND/OR
<br />CONSTRUCTION TO PREVENT DAMAGE. ANY DAMAGE TO REMAINING EXISTING EQUIPMENT
<br />SUSTAINED DURING DEMOLITION AND/OR CONSTRUCTION SHALL BE EQUIVALENTLY REPLACED OR
<br />EQUIVALENTLY REPAIRED AT NO COST TO THE OWNER.
<br />21. DO NOT INTERRUPT EXISTING UTILITIES, EXCEPT WHEN AUTHORIZED IN WRITING BY AUTHORITIES
<br />HAVING JURISDICTION.
<br />22. CONTRACTOR SHALL CONTACT ALL UTILITY COMPANIES INCLUDING BUT NOT LIMITED TO THE
<br />FOLLOWING: ELECTRIC, GAS, WATER, TELEPHONE, STORM SEWER, AND SANITARY SEWER FOR
<br />FIELD LOCATION OF ALL UNDERGROUND AND OVERHEAD UTILITY LINES. PRIOR TO
<br />COMMENCEMENT OF ANY DEMOLITION WORK, CONTRACTOR SHALL IDENTIFY ALL ELECTRICAL
<br />CIRCUITS SERVICING THE AREA INVOLVED WITH THIS DEMOLITION. THOSE CIRCUITS SHALL THEN
<br />BE LOCKED OUT AND TAGGED OUT IF THEY DO NOT SERVICE ANY OF THE REMAINING BUILDING.
<br />THOSE CIRCUITS WHICH ARE IDENTIFIED TO SERVICE BOTH THE AREA TO BE DEMOLISHED AND
<br />THE REMAINING BUILDING SHALL BE SPLIT SO AS TO KILL ALL ELECTRICAL POWER TO THE AREA
<br />TO BE DEMOLISHED WHILE MAINTAINING POWER TO THE REMAINDER OF THE BUILDING.
<br />23. ALL FURNITURE WILL BE REMOVED OR RELOCATED BY THE OWNER AS NECESSARY PRIOR TO THE
<br />DEMOLITION WORK OF THIS PROJECT. CONTRACTOR SHALL COORDINATE WITH THE OWNER AS
<br />REQUIRED.
<br />24. REMOVE EXISTING CONSTRUCTION TO THE EXTENT INDICATED ON THE DRAWINGS. SHOULD ANY
<br />DAMAGE OCCUR TO THE EXISTING CONSTRUCTION TO REMAIN, THE CONTRACTOR SHALL REPAIR
<br />THE DAMAGE TO MATCH EXISTING AND/OR ADJACENT CONSTRUCTION AT NO COST TO THE
<br />OWNER.
<br />ABBREVATIONS LEGEND
<br />A.B.
<br />ANCHOR BOLT
<br />JT
<br />JOINT
<br />AC
<br />ACCESS CONTROL
<br />ACOUST.
<br />ACOUSTICAL
<br />KB
<br />KNOX BOX
<br />ADJ.
<br />ADJUSTABLE
<br />KIT.
<br />KITCHEN
<br />A.F.F.
<br />ABOVE FINISH FLOOR
<br />KW.
<br />KILOWATT
<br />A.H.U.
<br />AIR HANDLING UNIT
<br />ALT.
<br />ALTERNATE
<br />L.
<br />LENGTH
<br />ALUM.
<br />ALUMINUM
<br />LAV.
<br />LAVATORY
<br />ANOD.
<br />ANODIZED
<br />LAM.
<br />LAMINATE
<br />A.P.
<br />ACCESS PANEL
<br />L.F.
<br />LINEAR FEET
<br />APP.
<br />APPROXIMATE
<br />LKR.
<br />LOCKER
<br />ARCH.
<br />ARCHITECTURAL
<br />L.L.
<br />LEAD LINED
<br />A.T.
<br />ACOUSTICAL TILE
<br />MAS.
<br />MASONRY
<br />BD.
<br />BOARD
<br />MAX.
<br />MAXIMUM
<br />BM.
<br />BEAM
<br />MECH.
<br />MECHANICAL
<br />BOT.
<br />BOTTOM
<br />MED.CAB.
<br />MEDICINE CABINET
<br />B.I.I.R.
<br />BUILT-UP ROOFING
<br />MTL.
<br />METAL
<br />BLDG.
<br />BUILDING
<br />MFD.
<br />MANUFACTURED
<br />MFR.
<br />MANUFACTURER
<br />CAB.
<br />CABINET
<br />M.H.
<br />MANHOLE
<br />C.F.C.I.
<br />CONTRACTOR
<br />MIN.
<br />MINIMUM
<br />FURNISHED
<br />MIR.
<br />MIRROR
<br />AND CONTRACTOR
<br />misc.
<br />MISCELLANEOUS
<br />INSTALLED
<br />MLDG.
<br />MOLDING
<br />C.G.
<br />CORNER GUARD
<br />M.O.
<br />MASONRY OPENING
<br />C.I.
<br />CASTIRON
<br />M.T.
<br />METAL THRESHOLD
<br />C.i.
<br />CONTROL JOINT
<br />MTD.
<br />MOUNTED
<br />CL.
<br />CLEAR
<br />CLO.
<br />CLOSET
<br />N.I.C.
<br />NOT IN CONTRACT
<br />C.M.U.
<br />CONCRETE
<br />NOM.
<br />NOMINAL
<br />MASONRY UNIT
<br />NTS.
<br />NOT TO SCALE
<br />COL.
<br />COLUMN
<br />O.A.
<br />OVERALL
<br />CONC.
<br />CONCRETE
<br />OFCL
<br />OWNER FURNISHED
<br />CONST.
<br />CONSTRUCTION
<br />CONTRACTOR
<br />CONT.
<br />CONTINUOUS
<br />INSTALLED
<br />CONTR.
<br />CONTRACTOR
<br />CORR.
<br />CORRIDOR
<br />O.C.
<br />ON CENTER
<br />CPT.
<br />CARPET
<br />O.D.
<br />OUTSIDE DIAMETER
<br />C.T.
<br />CERAMIC TILE
<br />CRT.
<br />COUNTER
<br />PL.
<br />PLATE
<br />P.LAM.
<br />PLASTIC LAMINATE
<br />DE
<br />DELAYED ENTRY
<br />PLAS.
<br />PLASTER
<br />DET.
<br />DETAIL
<br />PLUMB.
<br />PLUMBING
<br />DIA.
<br />DIAMETER
<br />PLWD.
<br />PLYWOOD
<br />DIAG.
<br />DIAGONAL
<br />P.T.
<br />PRESSURE TREATED
<br />DIM.
<br />DIMENSION
<br />P.T.D.
<br />PAPER TOWEL
<br />DISP.
<br />DISPENSER
<br />DISPENSER
<br />DN.
<br />DOWN
<br />DWG.
<br />DRAWING
<br />P.V.C.
<br />POLYVINYL CHLORIDE
<br />E.B.
<br />EXPANSION BOLT
<br />Q.T.
<br />QUARRY TILE
<br />E.J.
<br />EXPANSION JOINT
<br />EL.
<br />ELEVATION
<br />R.
<br />RADIUS
<br />ELEC.
<br />ELECTRICAL
<br />R.C.P.
<br />REINFORCED
<br />ELEV.
<br />ELEVATOR
<br />CONCRETE
<br />E.P.
<br />ELECTRICAL PANEL
<br />PIPE
<br />EQ.
<br />EQUAL
<br />EQUIP.
<br />EQUIPMENT
<br />R.D.
<br />ROOF DRAIN
<br />E.W.C.
<br />ELECTRIC
<br />REC.
<br />RECEPTACLE
<br />WATER COOLER
<br />REF.
<br />REFRIGERATOR
<br />EX.
<br />EXISTING
<br />REG.
<br />REGLET
<br />EXP.
<br />EXPOSED
<br />REINF.
<br />REINFORCED
<br />EXT.
<br />EXTERIOR
<br />REQD.
<br />REQUIRED
<br />RM.
<br />ROOM
<br />F.E.
<br />FIRE EXTINGUISHER
<br />R.O.
<br />ROUGH OPENING
<br />F.C.
<br />FURRING CHANNEL
<br />F.E.C.
<br />FIRE EXTINGUISHER CAB.
<br />SCRN.
<br />SCREEN
<br />FHV
<br />FIRE HOSE VALVE
<br />SCHD.
<br />SCHEDULE
<br />F.D.
<br />FLOOR DRAIN
<br />SEC.
<br />SECTION
<br />F.F.
<br />FINISH FLOOR
<br />SH.
<br />SHELF
<br />F.G.
<br />FIBERGLAS
<br />SHT.
<br />SHEET
<br />F.H.C.
<br />FIRE HOSE CABINET
<br />Sim.
<br />SIMILAR
<br />FIN.
<br />FINISH
<br />SP.
<br />SPACE
<br />FL.
<br />FLOOR
<br />SPECS.
<br />SPECIFICATIONS
<br />F.R.
<br />FIRE RATED
<br />ss.
<br />STAINLESS STEEL
<br />STL.
<br />STEEL
<br />GA.
<br />GUAGE
<br />STOR.
<br />STORAGE
<br />GALV.
<br />GALVANIZED
<br />STRUC.
<br />STRUCTURAL
<br />G.C.
<br />GENERAL CONTRACTOR
<br />SUSP.
<br />SUSPENDED
<br />GL.
<br />GLASS
<br />G.F.R.C.
<br />GLASS FIBER
<br />T.B.
<br />TOGGLE BOLT
<br />REINFORCED CEMENT
<br />T.C.
<br />TOILET
<br />G.F.R.G.
<br />GLASS FIBER
<br />COMPARTMENT
<br />REINFORCED GYPSUM
<br />GR.
<br />GRADE
<br />TEL.
<br />TELEPHONE
<br />GYP.
<br />GYPSUM
<br />TEMP.
<br />TEMPERATURE
<br />G.W.B.
<br />GYPSUM WALLBOARD
<br />T.P.D.
<br />TOILET PAPER
<br />DISPENSER
<br />HT.
<br />HEIGHT
<br />TYR
<br />TYPICAL
<br />H.B.
<br />HOSE BIBB
<br />HVAC
<br />HEATING,VENTILATING,
<br />U.C.
<br />UNDERCOUNTER
<br />& AIR CONDITIONING
<br />UTIL.
<br />UTILITY
<br />I.D.
<br />INSIDE DIAMETER
<br />V.B.
<br />VINYL BASE
<br />I.E.
<br />INVERT ELEVATION
<br />VEST.
<br />VESTIBULE
<br />INSUL.
<br />INSULATION
<br />VERT.
<br />VERTICAL
<br />INT.
<br />INTERIOR
<br />V.I.F.
<br />VERIFY IN FIELD
<br />V.W.C.
<br />VINYL WALLCOVERING
<br />W.
<br />WIDTH
<br />W/
<br />WITH
<br />W.C.
<br />WATER CLOSET
<br />WD.
<br />WOOD
<br />W.P.
<br />WEATHER PROOF
<br />W.W.F.
<br />WELDED WIRE FABRIC
<br />LEGEND
<br />I EXISTING WALLS TO REMAIN
<br />I NEW STUD FRAME WALLS
<br />I NEW CMU WALLS
<br />EXISTING DOORS / FRAME TO REMAIN
<br />REMOVE EXISTING DOOR / FRAME
<br />WALL TYPES
<br />Wl
<br />4" NOMINAL WOOD STUD INTERIOR
<br />WALL @ 16" O.C. MATCH DRYWALL
<br />EA. SIDE TO ALIGN W/ EXISTING
<br />WALLS AND PAINT
<br />W2
<br />4"NOMINAL WOOD STUD WALL @ 16"
<br />O.C. W/ 5/8"GWB TAPED AT FINISHED
<br />SIDE OF WALL, PAINT.
<br />W3
<br />2 1/4" FURRED OUT WALL STUDS @
<br />EX. WINDOW WALL LOCATIONS AT
<br />LIFT SHAFT @ 16 O.C. W/ 5/8- GWB
<br />TAPED AND PAINTED
<br />W4
<br />NEW 6" LT. GAGE STUDS @16' OC.
<br />,16 GAGE W/ 5/8" GWB EACH SIDE
<br />TAPED AND PAINTED W/ SOUND
<br />BATTON
<br />>1%
<br />oz
<br />uj
<br />CD
<br />C)
<br />CVD)
<br />cn
<br />Lo
<br />Lo
<br />0
<br />C?
<br />U- I-
<br />C?
<br />Tl-
<br />uj
<br />ci "IT
<br />`�
<br />cn
<br />c�
<br />z
<br />a
<br />E co)
<br />co)
<br />foo, CLOD
<br />co
<br />M .T cc)
<br />3: 04
<br />E
<br />0
<br />uj
<br />x
<br />M
<br />I
<br />cv) x
<br />cc
<br />. Lm -i LL
<br />m
<br />cr
<br />4) co
<br />> to
<br />u-
<br />=0
<br />m
<br /><
<br />F- co
<br />CLO)
<br />c
<br />c13 04
<br />0 4)
<br />0
<br />(D CLOO
<br />Lu
<br />"r
<br />04
<br />A
<br />M
<br />4) c�
<br />> m > CS
<br />0
<br />ml
<br />= o
<br />LU �
<br />00
<br />60 Lu "0 Lo
<br />Im Lo cm co
<br />00
<br />m
<br />E Colo
<br />4
<br />m IN
<br />0 C,) 075
<br />I I
<br /><
<br />I— �
<br />0 m 0 �-
<br />INFO
<br />SEAL
<br />CLIENT
<br />U.
<br />U-
<br />U)
<br />Lu
<br />N
<br />z
<br />(D
<br />u')
<br />cy)
<br />L0
<br />17
<br />PROJECT
<br />@CHANCEY DESIGN PARTNERSHIP
<br />TM DRAWW, � �L GRAPRC AND WRITTEN MATERIAL CONrPJNED FIIEREIN CIOWMUTES ORIGNAL
<br />AND LINPM ISI-ED WORK AND IS NOT TO BE COPIED. OMMSUTED. OR USFD IN W�E OR IN PAR7r.
<br />WrTHOUT EIPRESSED. WRrrrEN PERAIIISSION Ol' C� DIESIGN PARTNIER$1�91`. THS ORAWINIG IS
<br />�TFCTFD LWER T�F 'ARCAMMURAL WORKS OOPYPJC�ff PROTEC_nON ACT OF 1990.'
<br />PROJECT # � 21-170
<br />PROJ. ISSUED 08/25/2021
<br />SHEET ISSUED 08/25/2021
<br />NO. DATE DESCPJP71ON
<br />NOTES
<br />SHEET TITLE
<br />G001
<br />
|