|
ELECTRICAL LEGEND & FIXTURE SCHEDULE
<br />G.F.I. 110V LITHONIA WALL PACK LIGHTING
<br />SWITCH GROUND FAULT TWH LED ALO 40K 70 WAT OR
<br />S (b RECEPTACLE EQUAL TIMER CONTROLED
<br />oc
<br />OCCUPANCY SENOR
<br />(b 1110V
<br />WP 110V
<br />(D WATERPROOF
<br />OUTLET
<br />4=A 110VQUAD
<br />GF GROUND FAULT
<br />I" RECEPTACLE
<br />ELECTRICAL PANEL
<br />11 OV 180 CFM'S
<br />BROAN NUTONE
<br />505 BATH FAN
<br />METER
<br />+52" HUNTER MODEL 53323 INDOOR SMOKE ALARM
<br />OUTDOOR BRONZE CEILING FAN WITH BATTERY
<br />NO LIGHT KIT S BACK UP
<br />LITHONIA LIGHTING FMLWL
<br />LED WRAP SURFACE MOUNT
<br />FIXTURE 40.77 W 2900 LM OR
<br />EQUAL
<br />ELECTRICAL NOTES
<br />LITHONIA LIGHTING XVML LED
<br />VAPOR TIGHT SURFACE MOUNT
<br />FIXTURE 33 W 3500 LM OR EQUAL
<br />1. All work to be done in accordance with all current national and
<br />local codes and ordinances.
<br />2. Notify Engineer of any discrepancies between these drawings and the
<br />actual field conditions. Obtain clarifications from the Engineer or
<br />Owners prior to commencing work.
<br />3. Contractor will visit site prior to bidding, no allowances for any
<br />extra expenses will be granted as a result of not visiting site.
<br />4. Wire to be THHN/THWN Copper, min. size 14 AWG, unless shown otherwise.
<br />5. RACEWAYS: RIGID STEEL CONDUIT: full weight galvanized threaded pipe,
<br />EMT CONDUIT: compression fittings, PVC: schedule 40, all as allowed
<br />by local codes. Seperate raceways shall be used for each voltage system.
<br />6. Any installation conflict with other trades shall be brought to the
<br />attention of the Engineer for clarification before proceeding.
<br />7. Contractor will verify location of equipment and connect as required for
<br />clearances and connections.
<br />8. All ourdoor electrical equipment to be NEMA 3R rated.
<br />CONDUIT TO BE EXPOSED FLUSH
<br />MOUNT ON FACE OF INTERIOR BLOCK
<br />WALLS
<br />ELECTRICAL SPECIFICATIONS
<br />1.1 SCOPE
<br />A. WORK INCLUDED: Include the following Work in addition to items normally part of this Section:
<br />01 Wiring for lighting and power.
<br />02 Installation of lighting fixtures with lamps.
<br />03 Lighting panelboards and distribution panelboards.
<br />04 Connection of equipment shown.
<br />05 Control wiring.
<br />06 Disconnection and removal of existing fixtures and wiring not to be reused.
<br />1.2 MINIMUM COMPLIANCE STANDARDS
<br />A. All work shall be done in accordance with the requirements of the following:
<br />01 Latest adopted issue of the National Electrical Code, NFPA 70.
<br />02 Other applicable NFPA Codes.
<br />03 Regulation of local authorities having jurisdiction.
<br />B. Furnish and install all labor, material and equipment and services necessary for complete and
<br />safe installation of the electrical system indicated on the drawings and noted in the
<br />specifications hereinafter. Electrical systems and equipment shall in general include the
<br />following:
<br />01 General provisions for electrical work.
<br />02 Wiring, distribution equipment and devices.
<br />03 Lighting fixtures and lamps.
<br />04 Grounding system.
<br />1.3 GENERAL PROVISIONS FOR ELECTRICAL WORK
<br />A. DRAWINGS: Electrical drawings considered diagrammatic and indicate general arrangement of work
<br />and systems. Refer to other drawings to verify location of equipment, etc. Check drawings of
<br />other trades to verify exact space condition or underground lines. Drawing Scales prohibit the
<br />indication of all offsets, fittings and accessories required, however these items will be
<br />provided by this subcontractor at no extra cost to the owner.
<br />B. QUALITY OF MATERIALS: New, best of their respective kind, free from defects, and listed by
<br />Underwriter's Laboratories, Inc. or bearing their label.
<br />C. SHOP DRAWINGS: Submit four (4) copies of shop drawings for lighting fixtures and panelboards.
<br />Obtain approval before equipment is ordered, built or installed.
<br />D. EXCAVATION AND BACKFILLING: Excavate, backfill and restore surfaces for all electrical work.
<br />E. Visit site and inspect existing facilities before bid in order to ensure proper evaluation of
<br />working conditions and location of existing equipment.
<br />1.4 WIRING, DISTRIBUTION EQUIPMENT AND DEVICES
<br />A. CONDUCTORS: Copper, in accordance with ASTM Standards, size references AWG. Conductors No. 10 and
<br />smaller size solid, No. 8 and larger stranded. Insulation of conductor thermoplastic, type THHN
<br />(min. size: No. 12) any wire installed outside, underground, in slabs, or exposed to moisture
<br />shall have THWN insulation.
<br />B. RACEWAYS: RIGID STEEL CONDUIT, full weight pipe galvanized, threaded, and minimum 1/2 inch except
<br />as noted or required for wiring. ELECTRICAL METALLIC TUBING (EMT), thin wall pipe, galvanized, threadless,
<br />comiression fittings, and minimum 1/2" except as noted or required for wiring. FLEXIBLE STEEL CONDUIT,
<br />continuous singlestrip, galvanized, and minimum 1/2" size except as noted or required for wiring. PVC
<br />CONDUIT, heavy duty type, size as indicated. Type AC or MC cable where permitted. Separate raceways shall
<br />be used for each voltage system.
<br />C. DISCONNECT SWITCHES: General Duty, horsepower rated for motor loads 600 or 250 volt rating, fused
<br />or non -fused as noted; number of poles as indicated, cover interlocked with switch. Enclosure
<br />NEMA 1 for indoor use and NEMA 3R for weatherproof applications. Switch to be Square "D" or equal.
<br />D. CIRCUIT BREAKERS: Molded case, thermal -magnetic quick -make, quick -break, bolt -on type with
<br />manually operated insulated trip -free handle. Multi -pole types with internal common trip bar.
<br />Terminals suitable for copper or aluminum conductors. Interrupting capacity minimum 10,000 RMS
<br />symmetrical amperes circuit breakers to be Square "D" or equal, type as required.
<br />E. PANELBOARDS: Voltage, phasing and ampere ratings as indicated, circuit breaker type as indicated,
<br />busbars of hard drawn copper, minimum 98% conductivity, galvanized steel back box, door and trim.
<br />All corners lapped and welded, hardware chrome plated with flush lock and catch. Hinges semi -
<br />concealed, 5 knuckle steel with nonferrous pins, 180 degree openings. Minimum gutter space 5-
<br />3/4" sides, top and bottom. Increase size where required by code. Directory holder complete
<br />with clear plastic transparent cover indicating typewritten list of feeder cables, conduit sizes,
<br />circuit numbers, outlets of equipment supplied, and their location. Circuit breaker type
<br />panelboards to be Square "D" type NQOD or I -Line, or equal. A plastic label shall be located on exterior of
<br />panelboard identifying the system voltage, phase, and current rating.
<br />F. WIRING DEVICES: All devices the product of the same manufacturer. Wall switches sin le pole, 20
<br />_g
<br />ampere, 120 volt. Wall switches three-way, 20 ampere, 120 volt. Receptacles duplex, 2 wire; 3
<br />pole grounded, 20 ampere, 120 volt.
<br />G. DEVICE PLATES: Provide for all outlets where devices are installed. Provide engraved marking for
<br />special outlets. Provide blank plates for empty or future outlet boxes. DEVICE AND DEVICE PLATES
<br />COLORS TO BE VERIFIED WITH INTERIOR DESIGNER AND OWNER.
<br />1.5 LIGHTING FIXTURES AND LAMPS
<br />A. Furnish and install complete system of lighting fixtures, lamps, accessories and supports as
<br />specified and indicated. Submittals of equal quality are allowed.
<br />1.6 GROUNDING SYSTEM
<br />A. EQUIPMENT: Ground non -current carrying metal parts of panelboard, raceways and all lighting
<br />fixtures. All conduits shall have equipment grounding conductors.
<br />1.7 INSTALLATION
<br />A. Secure all supports to building structure. Support horizontal runs
<br />of metallic conduit not more than 10 feet apart. Run exposed raceways parallel with or at right
<br />angles to walls.
<br />B. Pass raceways over water, steam or other piping when pull boxes are not required. No raceway
<br />within 3 inches of steam or hot water pipes, or appliances, except crossings where raceway shall
<br />be at least 2 inches from pipe cover.
<br />C. Cut conduit ends square, ream smooth. Paint male threads of field threaded conduit with graphite
<br />base pipe compound. Draw up tight with conduit couplings.
<br />D. Leave wire sufficiently long to permit making final connections. In raceways over 50 feet in
<br />which wiring is not installed, furnish pull wire.
<br />E. Verify locations of outlets and switches.
<br />F. Support panel, junction and pull boxes independently to building structure with no weight bearing
<br />on conduits.
<br />G. Connect conduit to motor conduit terminal boxes with flexible conduit; minimum 18 inches in
<br />length and 50% slack. Do not terminate in or fasten raceways to motor foundation.
<br />H. Contractor to remove and salvage all abandoned electrical equiment.
<br />1. This contractor shall warrant all labor and materials for one year from date of final written
<br />acceptance.
<br />ELECTRICAL PLAN 1/491 = 1 1 off
<br />200 AMP 30 CIRC PANEL
<br />1 DED CIRCUIT I P2o 2 DED CIRCUIT 1 P20
<br />3 DED CIRCUIT I P20 4 DED CIRCUIT 1 P20
<br />5 DED CIRCUIT 1 P20 6 DED CIRCUIT 1 P20
<br />7 DED CIRCUIT 1 P20 8 DED CIRCUIT 1 P20
<br />9 DED CIRCUIT 1 P20 1 10 DED CIRCUIT 1 P20
<br />11 DED CIRCUIT 1 P20 12 DED CIRCUIT 1 P20
<br />13 DED CIRCUIT I P20 14 DED CIRCUIT 1 P20
<br />15 DED CIRCUIT 1 P20 16 DED CIRCUIT 1 P20
<br />17 CONCESSION LIGHTS/SMOKE ALARM 1 P20 18 EMERGENCY EIXT COMBO 1 P20
<br />19 EQUIP STORAGE &WATER FOUNTAIN 1 P20 20 WOMENS RESTROOM LIGHTS 1 P20
<br />21 RESTROOM GFI OUTLETS 1 P20 22 RESTROOM HAND DRYERS 1 P20
<br />23 MENS RESTROOM LIGHTS 1 P20 24 STORAGE LIGHT 1 P20
<br />25 OUTDOOR LIGHTS TIMER 1 P20 26 WATER HEATER 2P40
<br />271 OPEN 28 1 1
<br />291 MEETING ROOM LIGHTS/OUTLETS 1P20 . 30 1 MINI SPLIT UNIT I
<br />BUILDING LOAD CALCULATIONS
<br />LOAD DESCRIPTION DEMAND FACTOR TOTALS
<br />LIGHTING 1952 VA X 3 5856 VA
<br />RECEPTACLES ALLOWANCE 40 @ 180VA 7200 VA
<br />WATER HEATER 4500 VA
<br />TOTAL VA 17556 VA
<br />17556 74 AMPS
<br />240
<br />TYPICAL ELECTRICAL RISER DIAGRAM
<br />3 - 4/0 ALUMN
<br />2" GALV RISER
<br />METER SOCKET
<br />GROUND PER N.E.C.
<br />2- 4/0 #6 GROUND
<br />2" GALV NIPPLE
<br />CONCRETE ENCASED "LIFER"
<br />ELECTRODE REQUIRED PER
<br />CURRENT N.E.C. AND MUST
<br />BE INSPECTED PRIOR TO
<br />CONCRETE PLACEMENT
<br />ARKAY ENGINEERING INC.
<br />STRUCTURAL ENGINEERS
<br />RICHARD L. KIDDEY P.E.
<br />FLORIDA LICENSE NUMBER 37296
<br />I HERBY CERTIFY THAT THESE PLANS AND SPECIFICATIONS
<br />WERE PREPARED BY ME OR UNDER MY DIRECT SUPERVISION
<br />ARE IN COMPLIANCE WITH CHAPTER 16, SECTION 1609 OF THE
<br />FLORIDA BUILDING CODE 2017 6TH EDITION AND ASCE 7-10
<br />FOR 139 MPH WIND ZONE RISK CATEGORY 11
<br />CZ lu 01
<br />0 *
<br />Cq "o *
<br />Z Q)
<br />cil %D Q)
<br />C() M 19 0
<br />X.N -1
<br />W U_ b M
<br />L_
<br />%5 Q)
<br />LU C
<br />Z Q)
<br />W
<br />4_1 s-
<br />Q)
<br />tu
<br />Ot fJ
<br />Q)
<br />10
<br />6i
<br /><
<br />C)
<br />Z JCb I A
<br />0 C)
<br />LD I
<br />cf)
<br />W
<br />rl-
<br />co
<br />00 00
<br />L6 Ob
<br />L6
<br />Z 0
<br />bi Z
<br />I-- co
<br /><
<br />0
<br />(D
<br />Z
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />ELECTRICAL SPECIFICATIONS
<br />1.1 SCOPE
<br />A. WORK INCLUDED: Include the following Work in addition to items normally part of this Section:
<br />01 Wiring for lighting and power.
<br />02 Installation of lighting fixtures with lamps.
<br />03 Lighting panelboards and distribution panelboards.
<br />04 Connection of equipment shown.
<br />05 Control wiring.
<br />06 Disconnection and removal of existing fixtures and wiring not to be reused.
<br />1.2 MINIMUM COMPLIANCE STANDARDS
<br />A. All work shall be done in accordance with the requirements of the following:
<br />01 Latest adopted issue of the National Electrical Code, NFPA 70.
<br />02 Other applicable NFPA Codes.
<br />03 Regulation of local authorities having jurisdiction.
<br />B. Furnish and install all labor, material and equipment and services necessary for complete and
<br />safe installation of the electrical system indicated on the drawings and noted in the
<br />specifications hereinafter. Electrical systems and equipment shall in general include the
<br />following:
<br />01 General provisions for electrical work.
<br />02 Wiring, distribution equipment and devices.
<br />03 Lighting fixtures and lamps.
<br />04 Grounding system.
<br />1.3 GENERAL PROVISIONS FOR ELECTRICAL WORK
<br />A. DRAWINGS: Electrical drawings considered diagrammatic and indicate general arrangement of work
<br />and systems. Refer to other drawings to verify location of equipment, etc. Check drawings of
<br />other trades to verify exact space condition or underground lines. Drawing Scales prohibit the
<br />indication of all offsets, fittings and accessories required, however these items will be
<br />provided by this subcontractor at no extra cost to the owner.
<br />B. QUALITY OF MATERIALS: New, best of their respective kind, free from defects, and listed by
<br />Underwriter's Laboratories, Inc. or bearing their label.
<br />C. SHOP DRAWINGS: Submit four (4) copies of shop drawings for lighting fixtures and panelboards.
<br />Obtain approval before equipment is ordered, built or installed.
<br />D. EXCAVATION AND BACKFILLING: Excavate, backfill and restore surfaces for all electrical work.
<br />E. Visit site and inspect existing facilities before bid in order to ensure proper evaluation of
<br />working conditions and location of existing equipment.
<br />1.4 WIRING, DISTRIBUTION EQUIPMENT AND DEVICES
<br />A. CONDUCTORS: Copper, in accordance with ASTM Standards, size references AWG. Conductors No. 10 and
<br />smaller size solid, No. 8 and larger stranded. Insulation of conductor thermoplastic, type THHN
<br />(min. size: No. 12) any wire installed outside, underground, in slabs, or exposed to moisture
<br />shall have THWN insulation.
<br />B. RACEWAYS: RIGID STEEL CONDUIT, full weight pipe galvanized, threaded, and minimum 1/2 inch except
<br />as noted or required for wiring. ELECTRICAL METALLIC TUBING (EMT), thin wall pipe, galvanized, threadless,
<br />comiression fittings, and minimum 1/2" except as noted or required for wiring. FLEXIBLE STEEL CONDUIT,
<br />continuous singlestrip, galvanized, and minimum 1/2" size except as noted or required for wiring. PVC
<br />CONDUIT, heavy duty type, size as indicated. Type AC or MC cable where permitted. Separate raceways shall
<br />be used for each voltage system.
<br />C. DISCONNECT SWITCHES: General Duty, horsepower rated for motor loads 600 or 250 volt rating, fused
<br />or non -fused as noted; number of poles as indicated, cover interlocked with switch. Enclosure
<br />NEMA 1 for indoor use and NEMA 3R for weatherproof applications. Switch to be Square "D" or equal.
<br />D. CIRCUIT BREAKERS: Molded case, thermal -magnetic quick -make, quick -break, bolt -on type with
<br />manually operated insulated trip -free handle. Multi -pole types with internal common trip bar.
<br />Terminals suitable for copper or aluminum conductors. Interrupting capacity minimum 10,000 RMS
<br />symmetrical amperes circuit breakers to be Square "D" or equal, type as required.
<br />E. PANELBOARDS: Voltage, phasing and ampere ratings as indicated, circuit breaker type as indicated,
<br />busbars of hard drawn copper, minimum 98% conductivity, galvanized steel back box, door and trim.
<br />All corners lapped and welded, hardware chrome plated with flush lock and catch. Hinges semi -
<br />concealed, 5 knuckle steel with nonferrous pins, 180 degree openings. Minimum gutter space 5-
<br />3/4" sides, top and bottom. Increase size where required by code. Directory holder complete
<br />with clear plastic transparent cover indicating typewritten list of feeder cables, conduit sizes,
<br />circuit numbers, outlets of equipment supplied, and their location. Circuit breaker type
<br />panelboards to be Square "D" type NQOD or I -Line, or equal. A plastic label shall be located on exterior of
<br />panelboard identifying the system voltage, phase, and current rating.
<br />F. WIRING DEVICES: All devices the product of the same manufacturer. Wall switches sin le pole, 20
<br />_g
<br />ampere, 120 volt. Wall switches three-way, 20 ampere, 120 volt. Receptacles duplex, 2 wire; 3
<br />pole grounded, 20 ampere, 120 volt.
<br />G. DEVICE PLATES: Provide for all outlets where devices are installed. Provide engraved marking for
<br />special outlets. Provide blank plates for empty or future outlet boxes. DEVICE AND DEVICE PLATES
<br />COLORS TO BE VERIFIED WITH INTERIOR DESIGNER AND OWNER.
<br />1.5 LIGHTING FIXTURES AND LAMPS
<br />A. Furnish and install complete system of lighting fixtures, lamps, accessories and supports as
<br />specified and indicated. Submittals of equal quality are allowed.
<br />1.6 GROUNDING SYSTEM
<br />A. EQUIPMENT: Ground non -current carrying metal parts of panelboard, raceways and all lighting
<br />fixtures. All conduits shall have equipment grounding conductors.
<br />1.7 INSTALLATION
<br />A. Secure all supports to building structure. Support horizontal runs
<br />of metallic conduit not more than 10 feet apart. Run exposed raceways parallel with or at right
<br />angles to walls.
<br />B. Pass raceways over water, steam or other piping when pull boxes are not required. No raceway
<br />within 3 inches of steam or hot water pipes, or appliances, except crossings where raceway shall
<br />be at least 2 inches from pipe cover.
<br />C. Cut conduit ends square, ream smooth. Paint male threads of field threaded conduit with graphite
<br />base pipe compound. Draw up tight with conduit couplings.
<br />D. Leave wire sufficiently long to permit making final connections. In raceways over 50 feet in
<br />which wiring is not installed, furnish pull wire.
<br />E. Verify locations of outlets and switches.
<br />F. Support panel, junction and pull boxes independently to building structure with no weight bearing
<br />on conduits.
<br />G. Connect conduit to motor conduit terminal boxes with flexible conduit; minimum 18 inches in
<br />length and 50% slack. Do not terminate in or fasten raceways to motor foundation.
<br />H. Contractor to remove and salvage all abandoned electrical equiment.
<br />1. This contractor shall warrant all labor and materials for one year from date of final written
<br />acceptance.
<br />ELECTRICAL PLAN 1/491 = 1 1 off
<br />200 AMP 30 CIRC PANEL
<br />1 DED CIRCUIT I P2o 2 DED CIRCUIT 1 P20
<br />3 DED CIRCUIT I P20 4 DED CIRCUIT 1 P20
<br />5 DED CIRCUIT 1 P20 6 DED CIRCUIT 1 P20
<br />7 DED CIRCUIT 1 P20 8 DED CIRCUIT 1 P20
<br />9 DED CIRCUIT 1 P20 1 10 DED CIRCUIT 1 P20
<br />11 DED CIRCUIT 1 P20 12 DED CIRCUIT 1 P20
<br />13 DED CIRCUIT I P20 14 DED CIRCUIT 1 P20
<br />15 DED CIRCUIT 1 P20 16 DED CIRCUIT 1 P20
<br />17 CONCESSION LIGHTS/SMOKE ALARM 1 P20 18 EMERGENCY EIXT COMBO 1 P20
<br />19 EQUIP STORAGE &WATER FOUNTAIN 1 P20 20 WOMENS RESTROOM LIGHTS 1 P20
<br />21 RESTROOM GFI OUTLETS 1 P20 22 RESTROOM HAND DRYERS 1 P20
<br />23 MENS RESTROOM LIGHTS 1 P20 24 STORAGE LIGHT 1 P20
<br />25 OUTDOOR LIGHTS TIMER 1 P20 26 WATER HEATER 2P40
<br />271 OPEN 28 1 1
<br />291 MEETING ROOM LIGHTS/OUTLETS 1P20 . 30 1 MINI SPLIT UNIT I
<br />BUILDING LOAD CALCULATIONS
<br />LOAD DESCRIPTION DEMAND FACTOR TOTALS
<br />LIGHTING 1952 VA X 3 5856 VA
<br />RECEPTACLES ALLOWANCE 40 @ 180VA 7200 VA
<br />WATER HEATER 4500 VA
<br />TOTAL VA 17556 VA
<br />17556 74 AMPS
<br />240
<br />TYPICAL ELECTRICAL RISER DIAGRAM
<br />3 - 4/0 ALUMN
<br />2" GALV RISER
<br />METER SOCKET
<br />GROUND PER N.E.C.
<br />2- 4/0 #6 GROUND
<br />2" GALV NIPPLE
<br />CONCRETE ENCASED "LIFER"
<br />ELECTRODE REQUIRED PER
<br />CURRENT N.E.C. AND MUST
<br />BE INSPECTED PRIOR TO
<br />CONCRETE PLACEMENT
<br />ARKAY ENGINEERING INC.
<br />STRUCTURAL ENGINEERS
<br />RICHARD L. KIDDEY P.E.
<br />FLORIDA LICENSE NUMBER 37296
<br />I HERBY CERTIFY THAT THESE PLANS AND SPECIFICATIONS
<br />WERE PREPARED BY ME OR UNDER MY DIRECT SUPERVISION
<br />ARE IN COMPLIANCE WITH CHAPTER 16, SECTION 1609 OF THE
<br />FLORIDA BUILDING CODE 2017 6TH EDITION AND ASCE 7-10
<br />FOR 139 MPH WIND ZONE RISK CATEGORY 11
<br />CZ lu 01
<br />0 *
<br />Cq "o *
<br />Z Q)
<br />cil %D Q)
<br />C() M 19 0
<br />X.N -1
<br />W U_ b M
<br />L_
<br />%5 Q)
<br />LU C
<br />Z Q)
<br />W
<br />4_1 s-
<br />Q)
<br />tu
<br />Ot fJ
<br />Q)
<br />10
<br />6i
<br /><
<br />C)
<br />Z JCb I A
<br />0 C)
<br />LD I
<br />cf)
<br />W
<br />rl-
<br />co
<br />00 00
<br />L6 Ob
<br />L6
<br />Z 0
<br />bi Z
<br />I-- co
<br /><
<br />0
<br />(D
<br />Z
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />TYPICAL ELECTRICAL RISER DIAGRAM
<br />3 - 4/0 ALUMN
<br />2" GALV RISER
<br />METER SOCKET
<br />GROUND PER N.E.C.
<br />2- 4/0 #6 GROUND
<br />2" GALV NIPPLE
<br />CONCRETE ENCASED "LIFER"
<br />ELECTRODE REQUIRED PER
<br />CURRENT N.E.C. AND MUST
<br />BE INSPECTED PRIOR TO
<br />CONCRETE PLACEMENT
<br />ARKAY ENGINEERING INC.
<br />STRUCTURAL ENGINEERS
<br />RICHARD L. KIDDEY P.E.
<br />FLORIDA LICENSE NUMBER 37296
<br />I HERBY CERTIFY THAT THESE PLANS AND SPECIFICATIONS
<br />WERE PREPARED BY ME OR UNDER MY DIRECT SUPERVISION
<br />ARE IN COMPLIANCE WITH CHAPTER 16, SECTION 1609 OF THE
<br />FLORIDA BUILDING CODE 2017 6TH EDITION AND ASCE 7-10
<br />FOR 139 MPH WIND ZONE RISK CATEGORY 11
<br />CZ lu 01
<br />0 *
<br />Cq "o *
<br />Z Q)
<br />cil %D Q)
<br />C() M 19 0
<br />X.N -1
<br />W U_ b M
<br />L_
<br />%5 Q)
<br />LU C
<br />Z Q)
<br />W
<br />4_1 s-
<br />Q)
<br />tu
<br />Ot fJ
<br />Q)
<br />10
<br />6i
<br /><
<br />C)
<br />Z JCb I A
<br />0 C)
<br />LD I
<br />cf)
<br />W
<br />rl-
<br />co
<br />00 00
<br />L6 Ob
<br />L6
<br />Z 0
<br />bi Z
<br />I-- co
<br /><
<br />0
<br />(D
<br />Z
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />ARKAY ENGINEERING INC.
<br />STRUCTURAL ENGINEERS
<br />RICHARD L. KIDDEY P.E.
<br />FLORIDA LICENSE NUMBER 37296
<br />I HERBY CERTIFY THAT THESE PLANS AND SPECIFICATIONS
<br />WERE PREPARED BY ME OR UNDER MY DIRECT SUPERVISION
<br />ARE IN COMPLIANCE WITH CHAPTER 16, SECTION 1609 OF THE
<br />FLORIDA BUILDING CODE 2017 6TH EDITION AND ASCE 7-10
<br />FOR 139 MPH WIND ZONE RISK CATEGORY 11
<br />CZ lu 01
<br />0 *
<br />Cq "o *
<br />Z Q)
<br />cil %D Q)
<br />C() M 19 0
<br />X.N -1
<br />W U_ b M
<br />L_
<br />%5 Q)
<br />LU C
<br />Z Q)
<br />W
<br />4_1 s-
<br />Q)
<br />tu
<br />Ot fJ
<br />Q)
<br />10
<br />6i
<br /><
<br />C)
<br />Z JCb I A
<br />0 C)
<br />LD I
<br />cf)
<br />W
<br />rl-
<br />co
<br />00 00
<br />L6 Ob
<br />L6
<br />Z 0
<br />bi Z
<br />I-- co
<br /><
<br />0
<br />(D
<br />Z
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />rl-
<br />co
<br />00 00
<br />L6 Ob
<br />L6
<br />Z 0
<br />bi Z
<br />I-- co
<br /><
<br />0
<br />(D
<br />Z
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />Z
<br />0
<br />0
<br />W
<br />LIJ
<br />CL Z
<br />Ili
<br />N 0
<br />U_ 0
<br />00
<br />Z
<br />W
<br />U)
<br />D
<br />E 1
<br />ARKAY 17996
<br />MOUNT EACH UNIT 7'4" A.F.F.
<br />PIONEER MINI SPLIT SYSTEM
<br />MODEL WYS009AMFI 17RL
<br />-14-0��iT�U�;0--12.dVTPR-lf-SE-ER - - - - - - - - - - - - - - - - - - - - - - 7
<br />— — — — — — — — — — — -=7= :1- — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — - — — -- — — — — — —
<br />250 _350 SQ FT. CAPACITY 25 1
<br />METER I
<br />THt
<br />FEM-
<br />— -------------------------
<br />TD 25 200 A P T.C.
<br />ELEC N — 48" STORAGE —
<br />— 30 SHELVES 36" STORAGE —
<br />18
<br />TIT L WATER — E� SHELVES —
<br />63" COM DE =_P FREEZER REFRIG K
<br />=1 L36- iEATER —
<br />30" ICE 7 IKO 22 28 —
<br />MACHINE
<br />ri
<br />20
<br />19
<br />29 18 E=-
<br />GF
<br />HAND DRYER
<br />443 22
<br />19 2 30" STORAGE U 16
<br />X SHELVES
<br />4a 14,22 UJ
<br />9 1 19
<br />r LU 1 18-
<br />29�
<br />0][
<br />23 C
<br />17 18 0 17
<br />C)
<br />15 0"5
<br />R3
<br />18
<br />19-4 0
<br />14 12 10
<br />21
<br />0i
<br />X
<br />LU
<br />TAVL WALL
<br />2:;L
<br />X LLI
<br />17
<br />F` 30" ICE
<br />MACHINE
<br />T 18 8 6 4
<br />36" STORAJ
<br />SHELVES 48" STORAGE 36" R�FFRIG 63" COM D�P FREEZER
<br />\Irq 0- O_ :� 0=1C)_1
<br />F 7 7717,17 7 ------------------------ A MV
<br />L
<br />L----------- --------- --------------------------- ---------------------------------- ---------------------------- --------------- J
<br />
|