|
12
<br />4.01
<br />RAISED BANDS OR FOAM
<br />PER COMMUNITY
<br />SPECIFICATIONS
<br />----------------
<br />iJ
<br />N o CJ / WEEP
<br />SCORED �❑
<br />STUCCO
<br />00.
<br />(V r h
<br />0 N 4��
<br />i
<br />12
<br />15,0
<br />FIBEREGLASS SHINLGE INSTALLED
<br />AS PER MANUFACTURER
<br />SPECIFICATIONS
<br />M.
<br />TEXTURED is
<br />CE IOUS
<br />FINISHISH ON ON
<br />( r_ CMU (TYP)
<br />FIN FLR ,
<br />FRU"NT,ELEVATION - A
<br />9'-0" RIDGE VENT
<br />12
<br />— 15.0
<br />FIBEREGLASS SHINLGE INSTALLED
<br />AS PER MANUFACTURER
<br />SPECIFICATIONS
<br />EXTERIOR
<br />PLASTER ON
<br />FRAME
<br />CJ 25-SH CJ 12
<br />� 14.0
<br />------------------------------------------------------•----------------------------------------- —----------
<br />CJ/WEEP --- _--- �� —_
<br />TEXTURED
<br />CEMENTITIOUS
<br />FINISH ON
<br />CMU (TP)
<br />LEFT ELEVATION - A
<br />SCALE: 1/4" = 1'-0"
<br />General Notes
<br />ROOF CRITERIA:
<br />• 12" OVERHANG U.N.O.
<br />• PLUMB CUT FASCIA ROOF
<br />+ PITCH PER ELEVATION
<br />**G.C. VERIFY ROOF PITCH**
<br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE
<br />CONTRACTORS RESPONSIBILITY TO VERIFY
<br />ROOF SLOPE REQUIREMENTS WITH TRUSS
<br />MANUFACTURER.
<br />**ELECTRICAL SPECIFICATION NOTES**
<br />ELECTRICAL CONTRACTOR MUST VERIFY WITH
<br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE
<br />TO BE USED, LIGHT FIXTURES SHOWN ARE FOR
<br />LOCATION PURPOSES.
<br />Exterior Covering
<br />R703.7 Exterior Plaster.
<br />Installation of these materials shall be in compliance with ASTM
<br />C926 and ASTM C1063, or ASTM C1787 and the provisions of
<br />this code.
<br />R703.7.1 Lath.
<br />Lath and Lath attachments shall be of corrosion -resistant
<br />materials. Expanded metal or woven wire lath shall be attached
<br />with 1-1/2" long, 11 gage nails having
<br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in
<br />accordance with ASTM C1063 or C1787, or as otherwise
<br />approved. (Refer to sheet SN1 for the engineered method for
<br />Lath attachment.)
<br />Lathing Accessories
<br />Attachments shall be of corrosion -resistant materials.
<br />Wood Application: 16 Ga.x1-1/2" long (3/4%1" crown) staples @
<br />6" Q.C. vertically/horizontally into the framing members.
<br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia.
<br />min. @ 6" O.C. vertically/horizontally or compatible adhesives,
<br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C.
<br />or in a semi -continuous bead between the solid plaster base and
<br />the solid portion of the key attachment flange.
<br />Control Joints: Install control joint lathing accessories in
<br />conformance with C1063. Lath shall not be continuous through
<br />control joints, but shall be stopped and tied at each side.
<br />All accessories shall be in accordance with the latest ASTM
<br />C1063 & ASTM C1861.
<br />R703.7.2 Plaster.
<br />Plastering with cement plaster shall be not less than three coats
<br />where applied over any type of code -approved lath and shall be
<br />not less than two coats where directly applied over masonry,
<br />concrete, clay brick, stone, or tile. If the plaster surface is
<br />completely covered by veneer or other facing material or is
<br />completely concealed, plaster application need be only two coats,
<br />provided total thickness is as set in Table R702.1(1).
<br />Cement plaster shall be in accordance with ASTM C926 and
<br />material shall be in accordance with one of the types listed in
<br />R703.7.2.
<br />R703.7.3 Water -Resistive Barriers.
<br />Water -resistive barriers shall be installed as required in Section
<br />R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a
<br />performance at least equivalent to two layers of Grade D paper.
<br />The individual layers shall be installed independently such that
<br />each layer provides a separate continuous plane and any flashing
<br />(installed in accordance with Section R703,4) intended to drain to
<br />the water -resistive barrier is directed between the layers.
<br />R703.2 Water -Resistive Barrier,
<br />One layer of No. 15 asphalt felt, free from holes and breaks,
<br />complying with ASTM !D226 for Type 1 felt or other approved
<br />water -resistive barrier shall be applied over studs or sheathing of
<br />all exterior walls. No. 15 asphalt felt shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2
<br />inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance
<br />with the water -resistive barrier manufacturer's installation
<br />instructions. The No. 15 asphalt felt or other approved
<br />water -resistive barrier material shall be continuous to the top of
<br />walls and terminated at penetrations and building appendages in
<br />a manner to meet the requirements of the exterior wall envelope
<br />as described in Section R703.1.
<br />R703.4 Flashing.
<br />Approved metal flashing, vinyl flashing, self -adhered membranes
<br />and mechanically attached flexible flashing shall be applied
<br />shingle -fashion or in accordance with the manufacturer's
<br />instructions. Metal flashing shall be corrosion resistant.
<br />Fluid -applied membranes used as flashing shall be applied in
<br />accordance with the manufacturer's instructions. All flashing shall
<br />be applied in a manner to prevent the entry of water into the wall
<br />cavity or penetration of water to the building structural framing
<br />components.
<br />Self -adhered membranes used as flashing shall comply with
<br />AAMA 711. All exterior fenestration products shall be sealed at
<br />the juncture with the building wall with a sealant complying with
<br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for
<br />proper joint expansion and contraction, ASTM C1281, AAMA 812,
<br />or other approved standard as appropriate for the type of sealant.
<br />Fluid -applied membranes used as flashing in exterior walls shall
<br />comply with AAMA 714. The flashing shall extend to the surface
<br />of the exterior wall finish.
<br />Approved flashings shell be installed at the following locations.
<br />• Exterior window/door openings.
<br />• Intersection of chimneys or other masonry construction with
<br />frame walls.
<br />• Under and at the ends of masonry, wood or metal copings
<br />and sills.
<br />• Continuously above all projecting wood trim.
<br />• Where exterior porches, decks or stairs attach to a wall or
<br />floor assembly of wood -frame construction.
<br />• At wall and roof intersection.
<br />• At Built-in gutters.
<br />Coastal Flashings
<br />All flashing material for coastal locations (ex: within 3,000 feet of the
<br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless
<br />steel) and shall be selected for compatibility with adjacent wood
<br />preservatives per the manufacturer's recommendations.
<br />REV. 09,24.21
<br />eh
<br />cv
<br />00
<br />o
<br />I�
<br />4
<br />CL,
<br />Q
<br />LAA
<br />r
<br />• 47
<br />. l-3
<br />sx
<br />cCl>v
<br />c+
<br />cv
<br />eeaaaau:3t�+ao,r
<br />a -,
<br />Jr�A
<br />Lip Iti;tC �
<br />• • O�
<br />�.�� ..
<br />*. c�: •' t� is
<br />,
<br />N _ �'�f�i
<br />- No Pf"T 70
<br />:
<br />`
<br />•
<br />A.
<br />ST�'E
<br />OF
<br />r,
<br />A -
<br />�,J
<br />ee°�pa,
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifleations contained within these
<br />drawings comply with the 2020
<br />Florida Building Code -
<br />Residential 7th Edition. Engineer's signature and seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />0
<br />E
<br />c0 7J
<br />O'
<br />Ni
<br />iA ti r'. V w
<br />04
<br />ni
<br />v iL
<br />w LL d C7
<br />z
<br />�aw o
<br />Z
<br />= co CS o � o
<br />a
<br />IX Q
<br />W
<br />rn�a' C) z
<br />z
<br />LL &L
<br />00 d
<br />N M Z 1
<br />�
<br />Z
<br />o Cl C7 ❑
<br />W
<br />0 2
<br />cMv co
<br /><
<br />LL an
<br />M
<br />LL
<br />CNN
<br />Q
<br />10
<br />v7
<br />w ca
<br />"=
<br />O
<br />____
<br />w d
<br />V)
<br />,
<br />0y N
<br />r.a, �
<br />r
<br />N O/
<br />a
<br />I�
<br />o
<br />�
<br />Z
<br />tom.
<br />cr
<br />o
<br />E
<br />©
<br />U
<br />'�
<br />o°
<br />Zg
<br />CIO
<br />no
<br />O
<br />8
<br />>iU
<br /><0
<br />o U
<br />Qi
<br />C/> C
<br />3
<br />�°
<br />gz
<br />o
<br />o
<br />05
<br />a�
<br />Vm
<br />o c,
<br />z
<br />> Lo
<br />m
<br />CO
<br />N
<br />CL
<br />LO
<br />g
<br />cV
<br />t]—
<br />rCr
<br />m
<br />a—+
<br />O
<br />co
<br />O
<br />m
<br />M
<br />(0 G j
<br />o
<br />z
<br />E
<br />E
<br />N
<br />ca
<br />U
<br />a.
<br />d d
<br />_J
<br />JOB
<br />NO:
<br />23-02469
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />2.1
<br />
|