5520 20th St (2) - Laserfiche WebLink

Browse Search

WIND❑W WIDT A uF-on C E J K A B G M I SILL NOTES; 1. SHIM AS REQ'D AT EACH INSTALLATION ANCHOR W/L❑AD BEARING SHIM. MAX. ALLOWABLE SHIM STACK TO BE 1/4'. USE SHIMS WHERE SPACE GREATER THAN 1/16' IS PRESENT, 2. WINDOW FRAME MATERIAL: ALUMMINUM ALLOW 6063, 3, 3/16" DIA. CONCRETE SCREW ANCHOR MUST BE SUFFICIENT LTH, TO ACHIEVE MIN. EMBEDMENT OF 1 1/4' INT❑ MASONRY OR CONCRETE. (TYP LTH 2 3/4') 4. CAULK BEHIND WIND❑W FLANGE WITH DU❑-SIL ADHESIVE CAULK OR APPROVED EQUAL. APPLICATI❑N OF DUD-SIL ADHESIVE CAULK SEALANT MUST COMPLY WITH SEALANT MAUFACTURER'S REC❑MMENDATIONS. 5, USE LATEX CAULK OR EQUIVALENT FOR PERIMETER SEAL AROUND EXTERI❑R OF WIND❑W FLANGE BY OTHERS. 6. IF EXACT WIND❑W SIZE IS NOT LISTED IN ACHOR CHART, USE ANCHOR QUANTITY LISTED WITH NEXT LARGER SIZE FOR THE APPR❑PRIATE DESIGN PRESSURE REQ'D, 7. GLASS- THICKNESS MAY VARY PER THE REQUIREMENTS OF ASTM E1300 GLASS CHARTS. SINGLE GLAZING IS SHOWN. INSULATING GLASS ALSO QUALIFIED, 8. LETTER DESIGNATI❑NS ON THE ANCHOR L❑CATI❑N CHART INDICATE WHERE CONCRETE SCREW ANCHORS ARE TO BE INSTALLED WHEN USING EXTERIOR ELEVATI❑N AS A KEY. 9, NOT ALL ANCHORS SHOWN ON ELEVATION ARE APPLIED BY FACTORY IN ALL SIZES. ALL FACTORY APPLIED HOLES NOT DESIGNATED FOR CONCRETE SCREW ANCHOR SHOULD BE FILLED WITH #8 SCREWS OF SUFFICIENT LTH, TO PR❑VIDE MIN, 5/8 IN. EMBEDMENT INT❑ WOOD BUCK, FACTORY PUNCHED HOLES IN JAMBS ARE TO BE NO MORE THAN 6" FROM CORNERS AND 24' O.C. MAX. 1/4' MAX. SHIM SPACE W/ LOAD BRG SHIM WINDOW FRAME JAMB #8 ANCHOR WOOD SCREI 1 1/8' MIN. EMBEDMENT WINDOW WIDTH 2X BUCK STRIP I INTERIOR FINISH 1 X FURRING RIGID INSULATION E 3/16' TAPCON CONCRETE SCREW WITH A 1 1/4' MIN, EMBEDMENT EXTERIOR BLOCK WALL 1) CAULK BETWEEN BUCK AND MASONRY WALL 2) CAULK BETWEEN FLANGE AND WOOD BUCK 3) PERIMETER CAULK ALL EDGES 4) BUCK STRIP WIDTH PER CONTRACTOR MIN. WIDTH 2X4 MASONRY WIND❑W INSTALLATI❑N W/ 2X BUCK STRIPS 1/4' MAX. SHIM SPACE W/ LOAD BRG SHIM, WINDOW FRAME JAMB FLANGED WINDOW WINDOW WIDTH 1X BUCK STRIP 3/16' TAPCON CONCRETE SCREW WITH A 1 1/4' MIN. EMBEDMENT EXTERIOR BLOCK WALL 1) CAULK BETWEEN BUCK AND MASONRY WALL 2) CAULK BETWEEN FLANGE AND WOOD BUCK 3) PERIMETER CAULK ALL EDGES 4) BUCK STRIP WIDTH PER CONTRACTOR MIN. WIDTH 1X4 MASONRY WIND❑W INSTALLATI❑N W/ 1X BUCK STRIPS ANCHOR L❑CATI❑N CHART L❑CATI❑NS IN HEAD L❑CATIONS IN JAMB CALL SIZE BUCK SIZE UP TO 45 PSF 46 PSF TO 70 PSF UP TO 45 PSF 46 PSF TO 70 PSF SH 12 18 X 25 A,C A,C F,G F,G SH 13 18 X 37 3/8 A,C A,C F,G F,G SH 14 18 X 49 5/8 A,C A,C F,G F,G SH 15 18 X 62 A,C A,C F,G F,G,H,I SH 16 18 X 71 A,C A,C F,G F,G,H,I,N,O SH 17 18 X 83 A,C A,C F,G F,G,H,I,N,❑ SH 18 18 X 95 A,C A,C F,G,H,I F,G,H,I,N,❑ SH 32/2 25 3/8 X 25 A,C A,C F,G F,G SH 33/2 25 3/8 X 37 3/8 A,C A,C F,G F,G SH 34/2 25 3/8 X 49 5/8 A,C A,C F,G F,G,H,I SH 35/2 25 3/8 X 62 A,C A,C F,G F,G,H,I SH 36/2 25 3/8 X 71 A,C A,C F,G,H,I F,G,H,I,N,❑ SH 37/2 25 3/8 X 83 A,C A,C F,G,H,I F,G,H,I,N,❑ SH 38/2 25 3/8 X 95 A,C A,C F,G,H,I D,E,F,G,H,I,N,❑ SH 22 35 7/8 X 25 A,C A,C F,G F,G SH 23 35 7/8 X 37 3/8 A,C A,C F,G F,G,H,I SH 24 35 7/8 X 49 5/8 A,C A,C F,G F,G,H,I SH 25 35 7/8 X 62 A,C A,C F,G,H,I F,G,H,I SH 26 35 7/8 X 71 A,C A,C F,G,H,I D,E,F,G,H,I,N,❑ SH 27 35 7/8 X 83 A,C A,C F,G,H,I D,E,F,G,H,I,J,K,N,❑ SH 28 35 7/8 X 95 A,C A,C F,G,H,I D,E,F,G,H,I,J,K,N,❑ SH 32 52 X 25 A,C A,C F,G F,G SH 33 52 X 37 3/8 A,C A,C F,G,H,I F,G,H,I SH 34 52 X 49 5/8 AX A,C F,G,H,I F,G,H,I SH 35 52 X 62 A,C A,C F,G,H,I D,E,F,G,H,I SH 36 52 X 71 A,C A,C F,G,H,I D,E,F,G,H,I,N,❑ SH 37 152 X 83 A,C A,C D,E,F,G,H,I D,E,F,G,H,I,J,K,N,❑ SH 38 152 X 95 A,C A,C D,E,F,G,H,I D,E,F,G,H,I,J,K,L,M.N,❑ THE WINDOWS SPECIFIED ON THIS PLAN ARE BASED OF THE SIZES IN THIS CHART , IT IS THE BUILDERS RESP❑NSIBILITY TO VERIFY THAT THE SIZES OF THE WIND❑WS OF CH❑ICE ARE THE SAME OR ALLOWANCES MADE WHEN FRAMING IN THE ROUGH ❑PENINGS, WIND❑W SCHEDULE SIZE WIND❑W CODE MASONRY R,❑, SIZE 12 19 7/8" X 26' 13 19 7/8" X 38 3/8" 14 19 7/8" X 50 5/8' 15 19 7/8" X 63" 16 19 7/8" X 72" 32/2 27 1/4' X 26' 33/2 27 1/4' X 38 3/8" 34/2 27 1/4" X 50 5/8" 35/2 27 1/4" X 63' 36/2 27 1/4' X 72' 22 37 3/4' X 26' 23 37 3/4' X 38 3/8" 24 37 3/4' X 50 5/8' 2WE 37 3/4' X 56 1/4' 25 37 3/4' X 63' 26 37 3/4' X 72" 32 53 7/8' X 26" 33 53 7/8' X 38 3/8' 34 53 7/8' X 50 5/8" 3WE 53 7/8" X 56 1/4' 35 53 7/8' X 63' 36 53 7/8' X 72' WOOD FRAM R2 OPENING DEDUCT 1 1/4' FROM WIDTH 1/2" FROM HEIGHT MULL BARS FOR MOST LOW WIND AREAS ADD 1" PER MULL BAR TO ROUGH ❑PENINGS FOR SPECIAL HIGH WINDS LOAD AREAS MULL BAR SIZE MAY VARY, BE SURE TO CHECK WITH WIND❑W MANUFACTURER BEFORE CONSTRUCTION BEGINS, WIND❑W WIDTH - HEAD A C B G E SILL PICTURE WIND❑W NOTES: 1. SHIM AS REQ'D AT EACH INSTALLATION ANCHOR W/LOAD BEARING SHIM, MAX, ALLOWABLE SHIM STACK TO BE 1/4'. USE SHIMS WHERE SPACE GREATER THAN 1/16' IS PRESENT, 2. WIND❑W FRAME MATERIAL: ALUMMINUM ALLOW 6063. 3. 3/16' DIA, CONCRETE SCREW ANCHOR MUST BE SUFFICIENT LTH, TO ACHIEVE MIN. EMBEDMENT OF 1 1/4' INTO MASONRY OR CONCRETE, (TYP LTH 2 3/4') 4. CAULK BEHIND WINDOW FLANGE WITH DU❑-SIL ADHESIVE CAULK OR APPROVED EQUAL. APPLICATI❑N OF DU❑-SIL ADHESIVE CAULK SEALANT MUST COMPLY WITH SEALANT MAUFACTURER'S RECOMMENDATI❑NS, 5. USE LATEX CAULK OR EQUIVALENT FOR PERIMETER SEAL AROUND EXTERIOR OF WIND❑W FLANGE BY OTHERS, 6. IF EXACT WINDOW SIZE IS NOT LISTED IN ACH❑R CHART, USE ANCHOR QUANTITY LISTED WITH NEXT LARGER SIZE FOR THE APPROPRIATE DESIGN PRESSURE REQ'D. 7. GLASS THICKNESS MAY VARY PER THE REQUIREMENTS OF ASTM E1300 GLASS CHARTS, SINGLE GLAZING IS SHOWN. INSULATING GLASS ALSO QUALIFIED, 8. LETTER DESIGNATIONS ON THE ANCHOR L❑CATI❑N CHART INDICATE WHERE CONCRETE SCREW ANCHORS ARE TO BE INSTALLED WHEN USING EXTERIOR ELEVATION AS A KEY. 9. NOT ALL ANCHORS SHOWN ON ELEVATI❑N ARE APPLIED BY FACTORY IN ALL SIZES. ALL FACTORY APPLIED HOLES NOT DESIGNATED FOR CONCRETE SCREW ANCHOR SHOULD BE FILLED WITH #8 SCREWS OF SUFFICIENT LTH. TO PR❑VIDE MIN. 5/8 IN. EMBEDMENT INTO WOOD BUCK. FACTORY PUNCHED HOLES IN JAMBS ARE TO BE No MORE THAN 6' FROM CORNERS AND 24' O.C, MAX. 10, KINC❑ LTD'S TW SERIES PICTURE WINDOW IS SHOWN INSTALLION DEATILS ALSO APPLY To KINC'S TB SERIES PICTURE WIND❑WS AND KINC❑'S MARK 4-/50 PICTURE WINDOWS HALE CIRCLE WIND❑WS 1/2 WIDE 27 1/4" X 13 5/8' 2 WIDE 37 1/4" X 18 7/8' 3 WIDE 53 7/8" X 26 15/16" DBL 2 WIDE 75 1/2" X 37 3/4' DBL 3 WIDE 107 3/4' X 53 7/8" ADD ABOVE TO HEIGHT OF WIND❑W PLUS MULL. SEE YOUR MANUFACTURER FOR EXACT MULL THICKNESS THAT WILL BE USED FOR YOUR ❑PENING PLUS ALLOW FOR FRAMING ABOVE WITH A MAXIMUM 1/4" SHIM SPACE FROM THE WOOD FRAMING TO THE FRME OF THE WINDOW ANCHOR L❑CATI❑N CHART L❑CATI❑NS IN HEAD L❑CATI❑NS IN JAMBS CALL SIZE BUCK SIZE UP TO 40 PSF 41 PSF TO 60 PSF 61 PSF TO 70 PSF UP TO 40 PSF 41 PSF TO 60 PSF 61 PSF TO 70 PSF 0707 6 X 6 NONE NONE NONE F,G F,G F,G 0711 6 X 12 NONE NONE NONE F,G F,G F,G 0721 6 X 24 NONE NONE NONE F,G F,G F,G 0731 6 X 36 NONE NONE NONE F,G F,G F,G 0741 6 X 48 NONE NONE NONE F,G F,G F,G 0751 6 X 60 NONE NONE NONE F,G F,G F,G 1107 12 X 6 NONE NONE NONE F,G F,G F,G 1111 12 X 12 NONE NONE NONE F,G F,G F,G 1121 12 X 24 NONE NONE NONE F,G F,G F,G 1131 12 X 36 NONE NONE NONE F,G F,G F,G 1141 12 X 48 NONE NONE NONE F,G F,G F,G 1151 12 X 60 NONE NONE NONE F,G F,G F,G 2107 24 X 6 C C C F,G F,G F,G 2111 24 X 12 C C C F,G F,G F,G 2121 24 X 24 C C C F,G F,G F,G 2131 24 X 36 C C C F,G F,G F,G 2141 24 X 48 C C C F,G F,G F,G 2151 24 X 60 C C C F,G D,E,H,I D,E,H,I 3107 36 X 6 C C C F,G F,G F,G 3111 36 X 12 C C C F,G F,G F,G 3121 36 X 24 C C C F,G F,G F,G 3131 36 X 36 C C C F,G F,G F,G 3141 36 X 48 C C C F,G D,E,H,I D,E,H,I 3151 36 X 60 C C C F,G D,E,H,I D,E,H,I 4107 48 X 6 C C C F,G F,G F,G 4111 48 X 12 C C C F,G F,G F,G 4121 48 X 24 C C C F,G F,G F,G 4131 48 X 36 C C A,B F,G F,G F,G 4141 48 X 48 C C A,B F,G D,E,H,I D,E,H,I 4151 48 X 60 C C A,B D,E,H,I D,E,H,I D,E,H,I 5107 60 X 6 C C C D,E D,E D,E 5111 60 X 12 C C C D,E D,E D,E 5121 60 X 24 C C A,B D,E D,E D,E 5131 60 X 36 C A,B A,B D,E D,E D,E 5141 60 X 48 C A,B A,B D,E D,E,H,I D,E,H,I 5151 60 X 60 C A,B A,B D,E,H,I D,E,F,G,H,I D,E,F,G,H,I 6107 72 X 6 C C C D,E D,E D,E 6111 72 X 12 C C C D,E D,E D,E 6121 172 X 24 1 C A,B I A,B I D,E I D,E D,E 6131 72 X 36 A,B A,B A,B D,E D,E D,E 6141 72 X 48 A,B A,B A,B,C D,E D,E,H,I D,E,H,I 6151 72 X 60 A,B A,B,C A,B,C D,E,H,I D,E,F,G,H,I D,E,F,G,H,I NOTE; ACTUAL R.O. ❑PENINGS SIZES MUST BE VERIFIED BEFORE C❑NSTRUCTION BEGINS. ALL FASTENERS TO WOOD OR BLOCK MUST PENETRATE FRAME OF WIND❑W AND IN TO THE WALL MINIMUM 1 1/4'. ADD 1 1/2' TO WINDOWS ROUGH ❑PENING SIZE WHEN USING 2X BUCK STRIPS AND FLANGED WIND.❑WS ALL WORK SHALL COMPLY WITH PREVAILING CODES STANDARD BUILDING, PLUMBING, MECHANICAL, NEC, AND ALUMINUM, ALL OF THE PRODUCTS SPECIFIED ON THIS DRAWING OR ANY OTHER PAGE IN THIS PLAN MAY BE REPLACED WITH THOSE OF GREATER OR EQUAL VALUES, THIS INF❑RMATI❑N WAS ❑BTAINED THROUGH KINC❑ , LTD, OF 5245 OLD KINGS ROAD JACKS❑NVILLE FLORIDA 32254 FROM ENGINEERING PR❑VIDED FOR THE INSTALLATI❑N OF THEIR PRODUCT. IF OTHER THAN KINC❑ WIND❑WS ARE INSTALLED THE CONTRACTOR WILL NEED TO ❑BTAIN THE PROPER INSTALLATI❑N ENGINEERING FROM THE MANUF. OF CH❑ICE. ALL THE INF❑RMATI❑N ON THIS PAGE IS INTENDED TO BE CORRECT BUT MISTAKES CAN BE MADE AND IT IS THE RESP❑NSIBILITY OF THE CONTRACTOR TO VERIFY ALL INF❑RMATI❑N PRI❑R TO C❑NSTRUCTI❑N, WE WILL BE AVAILABLE TO HELP RESOLVE ANY PROBLEMS,