|
ELECTRICAL SPECIFICATIONS
<br />1.1 SCOPE
<br />A. WORK INCLUDED: Include the following Work in addition to items normally part of this Section:
<br />01 Wiring for lighting and power.
<br />02 Installation of lighting fixtures with lamps.
<br />03 Lighting panelboards and distribution panelboards.
<br />04 Connection of equipment shown.
<br />05 Control wiring.
<br />06 Disconnection and removal of existing fixtures and wiring not to be reused.
<br />1.2 MINIMUM COMPLIANCE STANDARDS
<br />A. All work shall be done in accordance with the requirements of the following:
<br />01 Florida Building Code Sixth Edition (2017).
<br />02 Florida Building Code - Electrical Conservation Sixth Edition (2017), Section C405.
<br />03 2014 issue of the National Electrical Code (NFPA 70).
<br />04 All Receptacle Control to conform to ASHRAE Standard 90.1, 8.4.2, 2010.
<br />05 Wiring in Patient Care Areas shall comply with NEC 517.
<br />06 Other applicable NFPA Codes.
<br />07 Regulation of local authorities having jurisdiction.
<br />B. Furnish and install all labor, material and equipment and services necessary for complete and
<br />safe installation of the electrical system indicated on the drawings and noted in the
<br />specifications hereinafter. Electrical systems and equipment shall in general include the following:
<br />01 General provisions for electrical work.
<br />02 Wiring, distribution equipment and devices.
<br />03 Lighting fixtures and lamps.
<br />04 Grounding system.
<br />1.3 GENERAL PROVISIONS FOR ELECTRICAL WORK
<br />A. DRAWINGS: Electrical drawings considered diagrammatic and indicate general arrangement of work
<br />and systems. Refer to other drawings to verify location of equipment, etc. Check drawings of
<br />other trades to verify exact space condition or underground lines. Drawing Scales prohibit the
<br />indication of all offsets, fittings and accessories required, however these items will be
<br />provided by this subcontractor at no extra cost to the owner.
<br />B. QUALITY OF MATERIALS: New, best of their respective kind, free from defects, and listed by
<br />Underwriter's Laboratories, Inc. or bearing their label.
<br />C. SHOP DRAWINGS: Submit four (4) copies of shop drawings for lighting fixtures and panelboards.
<br />Obtain approval before equipment is ordered, built or installed.
<br />D. EXCAVATION AND BACKFILLING: Excavate, backfill and restore surfaces for all electrical work.
<br />E. Visit site and inspect existing facilities before bid in order to ensure proper evaluation of
<br />working conditions and location of existing equipment.
<br />1.4 WIRING, DISTRIBUTION EQUIPMENT AND DEVICES
<br />A. CONDUCTORS: Copper, in accordance with ASTM Standards, size references AWG. Conductors No. 10 and
<br />smaller size solid, No. 8 and larger stranded. Insulation of conductor thermoplastic, type THHN
<br />(min. size: No. 12) any wire installed outside, underground, in slabs, or exposed to moisture
<br />shall have THWN insulation.
<br />B. RACEWAYS: RIGID STEEL CONDUIT, full weight pipe galvanized, threaded, and minimum 1/2 inch except
<br />as noted or required for wiring. ELECTRICAL METALLIC TUBING (EMT), thin wall pipe, galvanized, threadless,
<br />comression fittings, and minimum 1/2" except as noted or required for wiring. FLEXIBLE STEEL CONDUIT,
<br />continuous singlestrip, galvanized, and minimum 1/2" size except as noted or required for wiring. PVC
<br />CONDUIT, heavy duty type, size as indicated. Separate raceways shall be used for each voltage system.
<br />Type AC or MC Cable where permitted.
<br />C. DISCONNECT SWITCHES: General Duty, horsepower rated for motor loads 600 or 250 volt rating, fused
<br />or non -fused as noted; number of poles as indicated, cover interlocked with switch. Enclosure
<br />NEMA 1 for indoor use and NEMA 3R for weatherproof applications. Switch to be Square "D" or equal.
<br />D. CIRCUIT BREAKERS: Molded case, thermal -magnetic quick -make, quick -break, bolt -on type with
<br />manually operated insulated trip -free handle. Multi -pole types with internal common trip bar.
<br />Terminals suitable for copper or aluminum conductors. Interrupting capacity minimum 10,000 RMS
<br />symmetrical amperes circuit breakers to be Square "D" or equal, type as required.
<br />E. PANELBOARDS: Voltage, phasing and ampere ratings as indicated, circuit breaker type as indicated,
<br />busbars of hard drawn copper, minimum 98% conductivity, galvanized steel back box, door and trim.
<br />All corners lapped and welded, hardware chrome plated with flush lock and catch. Hinges semi -
<br />concealed, 5 knuckle steel with nonferrous pins, 180 degree openings. Minimum gutter space 5-
<br />3/4" sides, top and bottom. Increase size where required by code. Directory holder complete
<br />with clear plastic transparent cover indicating typewritten list of feeder cables, conduit sizes,
<br />circuit numbers, outlets of equipment supplied, and their location. Circuit breaker type
<br />panelboards to be Square "D" type NQOD or I -Line, or equal. A plastic label shall be located on exterior of
<br />panelboard identifying the system voltage, phase, and current rating.
<br />F. WIRING DEVICES: All devices the product of the same manufacturer. Wall switches single pole, 20
<br />ampere, 120 volt. Wall switches three-way, 20ampere, 120 volt. Receptacles duplex, 2 wire; 3
<br />pole grounded, 20 ampere, 120 volt.
<br />G. DEVICE PLATES: Provide for all outlets where devices are installed. Provide engraved marking for
<br />special outlets. Provide blank plates for empty or future outlet boxes. DEVICE AND DEVICE PLATES
<br />COLORS TO BE VERIFIED WITH INTERIOR DESIGNER AND OWNER.
<br />1.5 LIGHTING FIXTURES AND LAMPS
<br />A. Furnish and install complete system of lighting fixtures, lamps, accessories and supports as
<br />specified and indicated. Submittals of equal quality are allowed.
<br />1.6 GROUNDING SYSTEM
<br />A. EQUIPMENT: Ground non -current carrying metal parts of panelboard, raceways and all lighting
<br />fixtures. All conduits shall have equipment grounding conductors.
<br />1.7 INSTALLATION
<br />A. Secure all supports to building structure. Support horizontal runs
<br />of metallic conduit not more than 10 feet apart. Run exposed raceways parallel with or at right
<br />angles to walls.
<br />B. Pass raceways over water, steam or other piping when pull boxes are not required. No raceway
<br />within 3 inches of steam or hot water pipes, or appliances, except crossings where raceway shall
<br />be at least 2 inches from pipe cover.
<br />C. Cut conduit ends square, ream smooth. Paint male threads of field threaded conduit with graphite
<br />base pipe compound. Draw up tight with conduit couplings.
<br />D. Leave wire sufficiently long to permit making final connections. In raceways over 50 feet in
<br />which wiring is not installed, furnish pull wire.
<br />E. Verify locations of outlets and switches.
<br />F. Support panel, junction and pull boxes independently to building structure with no weight bearing
<br />on conduits.
<br />G. Connect conduit to motor conduit terminal boxes with flexible conduit; minimum 18 inches in
<br />length and 50% slack. Do not terminate in or fasten raceways to motor foundation.
<br />H. Contractor to remove and salvage all abandoned electrical equiment.
<br />I. This contractor shall warrant all labor and materials for one year from date of final written
<br />acceptance.
<br />J. Owner assumes responsibility to do periodic maintenance on all Aluminum Wire Connections and will
<br />provide a signed letter to attest to this agreement.
<br />K. Contractor will provide to the Building Owner, within 30 days after the date of the system acceptance, record
<br />drawings of the actual installation Documents and Manuals per C405.6.4
<br />L. Contractor shall provide construction documents that certify lighting controls meet performance criteria of
<br />Section C405 of the Florida Building Code Sixth Edition (2017) Energy Conservation, and provided to the
<br />Building Owners within 90 days of receipt of the Certificate of Occupancy per C408.3.2 of the same code.
<br />M. Contractor shall provide field markings on all Service Equipment in field. Field markings shall include the
<br />date the fault -current calculation was performed and be of sufficient durability to withstand the environment
<br />involed per NEC 110.24.
<br />1.8 LOW VOLTAGE
<br />A. Low Voltage wiring drawings to be provided by others.
<br />F"I 17rTRlrnl CYkAQnl C
<br />SFV - VARIABLE SPEED CEILING FAN CONTROL RATED FOR THE LOAD
<br />S3D- 3-WAY SINGLE POLE DIMMER SWITCH (0-10V OR LINE VOLT. AS REQUIRED)
<br />SD - SINGLE POLE DIMMER SWITCH (0-10V OR LINE VOLTAGE AS REQUIRED)
<br />Sap - 3-WAY SINGLE POLE TOGGLE SWITCH W/PILOT LIGHT
<br />S - SINGLE POLE TOGGLE SWITCH
<br />S3 - 3-WAY SINGLE POLE TOGGLE SWITCH
<br />Sa - "a/b" INDICATES LIGHTS TO BE SWITCHED
<br />Daub - OCCUPANCY SENSOR W/TWO LEVELS OF LIGHTING LINE VOLTAGE
<br />- TIME CLOCK OVERIDE SWITCH (MAX. 2 HR)
<br />1O - LINE VOLTAGE WALL MOUNTED OCCUPANCY SENSOR
<br />® - LINE VOLTAGE CEILING MOUNTED OCCUPANCY SENSOR
<br />O - LINE VOLTAGE CEILING MOUNTED OCCUPANCY SENSOR (LARGE RESTROOMS)
<br />® - LINE VOLTAGE WALL MOUNTED OCCUPANCY SENSOR (SMALL RESTROOMS)
<br />Q - LINE VOLTAGE WALL MOUNTED OCCUPANCY SENSOR W/2 LIGHT CONTROL
<br />-(SEE SWITCH DETAIL)
<br />© - WALL MOUNTED OCCUPANCY SENSOR (CLOSETS)
<br />© - WALL MOUNTED DIMMABLE OCCUPANCY SENSOR
<br />VERIFY LINE VOLTAGE OR 0-10V
<br />® - MANUAL "ON" OCCUPANCY SENSOR
<br />0 - MANUAL "ON" DIMMABLE OCCUPANCY SENSOR
<br />VERIFY LINE VOLTAGE OR 0-10V
<br />- LINE VOLTAGE CEILING MOUNTED OCCUPANCY SENSOR FOR RECEPTACLES
<br />DS - DAYLIGHT SENSOR
<br />-SPLIT DUPLEX RECEPTACLE HALF ON TIME CLOCK OR OCCUPANCY SENSOR.
<br />C= RECEPTACLES MUST BE MARKED TO INDICATE THAT THEY ARE CONTROLLED.
<br />- QUADRAPLEX RECEPTACLE HALF ON TIME CLOCK OR OCCUPANCY SENSOR.
<br />C RECEPTACLES MUST BE MARKED TO INDICATE THAT THEY ARE CONTROLLED.
<br />- DUPLEX RECEPTACLE ON TIME CLOCK OR OCCUPANCY SENSOR. CONTROLLED
<br />RECEPTACLES MUST BE MARKED TO INDICATE THAT THEY ARE CONTROLLED.
<br />-e - SIMPLEX RECEPTACLE
<br />- DUPLEX RECEPTACLE
<br />- QUADRAPLEX RECEPTACLE
<br />- FLOOR BOX W/DUPLEX RECEPTACLE. LOCATIONS TO BE VERIFIED W/OWNERS
<br />- FLOOR BOX W/QUADRAPLEX RECEPTACLE. VERIFY LOCATIONS W/OWNERS
<br />TVO - 3/4" CONDUIT TO CABLE EQUIPMENT/VERIFY TERMINATION W/OWNERS
<br />GFI - GROUND FAULT INTERRUPTER
<br />WP - WATER PROOF 3R - NEMA 3R
<br />NF - NON -FUSED NIL - NIGHT LIGHT
<br />- DISCONNECT SWITCH
<br />_ - ELECTRICAL PANELBOARD
<br />�- EMERGENCY LIGHTING/EXIT SIGN W/BATTERY BACKUP
<br />EMERGENCY LIGHTING-W/BATTERY BACKUP 3
<br />TC - TIME CLOCK
<br />® - PHOTO ELECTRIC SENSOR
<br />® - 208V 30 RECEPTACLE
<br />- CONDUIT IN FLOOR
<br />RC - RECEPTACLE CONTACTOR
<br />® - 208V RECEPTACLE - VERIFY
<br />1>1 N - 2 VOICE (CAT 5) OUTLET
<br />DATA & COMMUNICATIONS TO BE VERIFIED W/OWNERS
<br />- DATA (CAT 6) OUTLET
<br />DATA & COMMUNICATIONS TO BE VERIFIED W/OWNERS
<br />- RESTROOM EXHAUST FAN
<br />EXTERIOR SECURITY CAMERA 4"X4" JUNCTION BOX W/1 " CONDUIT TO CAMERA
<br />© EQUIPMENT. LOCATIONS TO BE VERIFIED W/OWNERS
<br />®- INTERIOR SECURITY CAMERA 4"X4" JUNCTION BOX W/1 " CONDUIT TO CAMERA
<br />EQUIPMENT. LOCATIONS TO BE VERIFIED W/OWNERS
<br />- SECURITY SENSORS - 4"x4" J-BOX W/1" CONDUIT TO
<br />EQUIPMENT. LOCATIONS TO BE VERIFIED W/OWNERS
<br />OUTDOOR CEILING FAN - TO BE PICKED BY OWNERS
<br />NOTE:
<br />Occupancy Sensors are to be "Occupancy/Vacancy Sensors unless indicated
<br />otherwise. ie: "Manual On" is a Vacancy sensor w/auto off.
<br />1 " RGS
<br />2 Sets Ea. (4)3/0,2"C
<br />2 Sets Ea. (4)3/0,2"C
<br />To
<br />Utility Transformer
<br />PANEL "L1 " SCHEDULE
<br />SERVES
<br />LO�ABD
<br />CB/P
<br />CKT
<br />B/P
<br />LO�ABD
<br />SERVES
<br />0A �C
<br />�A �C
<br />Customer Area Lights
<br />842
<br />20/1
<br />1
<br />2
<br />15/1
<br />1296
<br />Ice Machine
<br />Customer Area/Bar Lts
<br />821
<br />20/1
<br />3
<br />4
<br />15/1
<br />276
<br />Bottle Cooler
<br />Pool Table/Patio Lts.
<br />287
<br />20/1
<br />5
<br />6
<br />40/2
<br />1675
<br />Cooler Condenser
<br />Spare
<br />20/1
<br />7
<br />8
<br />1
<br />1675
<br />1
<br />Walk in Cooler Lts.
<br />500
<br />20/1
<br />9
<br />10
<br />20/2
<br />811
<br />Evaporator 1
<br />Ext. Bldg. Lts.
<br />221
<br />20/1
<br />11
<br />12
<br />1
<br />811
<br />1
<br />Spare
<br />20/1
<br />13
<br />14
<br />20/2
<br />811
<br />Evaporator 2
<br />Bar Receptacle
<br />1500
<br />20/1
<br />15
<br />16
<br />I
<br />811
<br />1
<br />Bar Receptacle
<br />1500
<br />20/1
<br />17
<br />18
<br />20/1
<br />1500
<br />Security Power
<br />Space
<br />19
<br />20
<br />30/2
<br />2250
<br />Water Heater
<br />1
<br />21
<br />22
<br />I
<br />2250
<br />1
<br />Storage/Rstrm/Off Lts.
<br />1180
<br />20/1
<br />23
<br />24
<br />2 /1
<br />1500
<br />Bar Counter Recept.
<br />Space
<br />25
<br />26
<br />20/1
<br />1500
<br />Bar Counter Recept.
<br />27
<br />28
<br />20/1
<br />1500
<br />Bar Counter recept.
<br />29
<br />30
<br />20/1
<br />500
<br />Soda Dispenser
<br />RTU-1
<br />8310
<br />100/3
<br />31
<br />32
<br />20/1
<br />500
<br />Soda Dispenser
<br />8310
<br />33
<br />34
<br />20/1
<br />500
<br />POS Station
<br />8310
<br />I
<br />35
<br />36
<br />20/1
<br />540
<br />Bar TV Recept.
<br />RTU-2
<br />8310
<br />100/3
<br />37
<br />38
<br />20/1
<br />1500
<br />Vending
<br />8310
<br />I
<br />39
<br />40
<br />20/1
<br />1500
<br />Vending
<br />8310
<br />1 41
<br />42
<br />120 1
<br />1
<br />1 1500
<br />1 Vendin
<br />Sub -Total 174621944119808 9532 1 7648 1 6026
<br />Panel L2 11627 092712327
<br />-- - -- ...- - 114818 = 322 Amps Connected (Highest Phase)
<br />Total 38641 38016 38161 106781 = 296 Amps Demand
<br />Notes: 400A MLO 120/208V 30 4W SN w/Feed Thru Lugs
<br />PANEL 12" SCHEDULE
<br />SERVES
<br />OA LO�ABD �C
<br />CB/P
<br />CKT
<br />B/P
<br />�A LO�ABD �C
<br />SERVES
<br />Stage Lights
<br />1000
<br />20/1
<br />1
<br />2
<br />20/1
<br />1500
<br />POS Equipment
<br />Stage Lights
<br />1000
<br />20/1
<br />3
<br />4
<br />20/1
<br />500
<br />ATM Machine
<br />East Recept/TV's
<br />720
<br />20/1
<br />5
<br />6
<br />20/1
<br />720
<br />Office Receptacles
<br />East Recept/TV's
<br />1080
<br />20/1
<br />7
<br />8
<br />20/1
<br />1080
<br />Storage Recept.
<br />North Recpt./TV
<br />540
<br />20/1
<br />9
<br />10
<br />20/1
<br />900
<br />Ext. Bldg. Recept.
<br />West Recpt./TV's
<br />900
<br />20/1
<br />11
<br />12
<br />20/1
<br />1500
<br />Stage Recept.
<br />Recept/DF
<br />480
<br />20/1
<br />13
<br />14
<br />20/2
<br />1500
<br />Stage Recept.
<br />Sign
<br />1500
<br />20/1
<br />15
<br />16
<br />20/1
<br />1500
<br />Stage Recept.
<br />Fans
<br />500
<br />20/1
<br />17
<br />18
<br />20/1
<br />1500
<br />Stage Recept.
<br />Spare
<br />20/1
<br />19
<br />20
<br />20/1
<br />1500
<br />Stage Recept.
<br />Space
<br />21
<br />22
<br />20/1
<br />1500
<br />Stage Recept.
<br />Sign
<br />1500
<br />20/1
<br />23
<br />24
<br />20/1
<br />1500
<br />Sign
<br />Space
<br />20/1
<br />25
<br />26
<br />15/3
<br />497
<br />1 HP Irrigation Pump
<br />27
<br />28
<br />497
<br />29
<br />30
<br />I
<br />497
<br />31
<br />32
<br />Space
<br />33
<br />34
<br />35
<br />36
<br />RTU-3
<br />2990
<br />35/3
<br />37
<br />38
<br />2990
<br />39
<br />40
<br />2990
<br />I
<br />41
<br />42
<br />Sub -Total 5550 6030 6610 6077 4897 5717
<br />Total 11627 092712327 34881 = 103 Amps Connected (Highest Phase)
<br />Notes: 400A MLO 120/208V 30 4W SN
<br />Extend to metal water line
<br />or building steel in accordance
<br />with NEC 250.
<br />3% EQUIPMENT VOLTAGE DROP CHART
<br />This chart is based on a 20 amp single pole
<br />breaker load at maximum (16 amps)
<br />120/208V 30 Service.
<br />WIRE TYPE AND SIZE FEET
<br /># 12 75-C THW/THWN Wire = 113
<br /># 10 75-C THW/THWN Wire = 181
<br />J
<br />Meter
<br />C.T
<br />If required
<br />2 CU
<br />400/3
<br />Main
<br />Fused
<br />Disc.
<br />Nipple thru wall
<br />Minimum (2)5/8" 0 Copper Clad
<br />Ground Rods spaced 10' apart.
<br />Panel L1
<br />400A MLO
<br />120/208V
<br />30 4 Wire
<br />SN
<br />W/Feed
<br />thru Lugs
<br />Proposed Building
<br />ELECTRICAL LOAD CALCULATIONS:
<br />LIGHTING
<br />5000 Sq. Ft. ® 1.01 per =
<br />Per Table C405.4.2(1)
<br />Exterior Bldg. Lights
<br />Stage Lighting
<br />Continuous Load = 7.27 X 1.25 =
<br />RECEPTACLES
<br />1st 10kw ® 100% + .5 X remainder =
<br />10000 + (.5 X 22960) =
<br />HVAC
<br />(2) RTU's Unit w/Heat ® 24930 ea. _
<br />(1) RTU's Unit w/Heat ® 8970 =
<br />EQUIPMENT
<br />(1) Ice Machine ® 1296 =
<br />(1) Bottle Cooler ® 276 =
<br />(1) Walk In Cooler Condenser ® 3350 =
<br />(2) Walk In Cooler Evaporators @ 1622 ea. _
<br />(1) Water Heater ® 4500 =
<br />(3) Signs ® 1500 ea. =
<br />2 Ceiling Fans ® 250 ea. _
<br />1 HP Irrigation Pump
<br />KW
<br />5.05
<br />0.22
<br />2.00
<br />7.27
<br />Sub Total 9.09
<br />10.00
<br />11.48
<br />Sub Total 21.48
<br />49.86
<br />ff
<br />8.97
<br />Sub Total 58.83
<br />0
<br />1.30
<br />0.28
<br />3.35
<br />3.24
<br />otal 8.17
<br />0
<br />0
<br />4.50 N
<br />4.50 Z
<br />0.50
<br />1.49
<br />Total 108.56
<br />108.56kw ® 120/208V 30 = 301 Amps.
<br />400A 120/208V 30 4 Wire SN Service
<br />cunRT rIPrl IIT rel rlll OTInNc�-
<br />43198 (Worst Case)
<br />Sc = 1 + 1.732(50)(43198)
<br />2(13923)(208)
<br />1 Sc = 26247.0 AIC 400A Fused Disconnect
<br />I SC = 9500.0 AIC Let Thru Current ® 400A Fused Disc
<br />w/400A Class RK1 LPN-RK_SP Fuses
<br />I Sc = <10000 AIC Panels L1, and L2
<br />2% SERVICE/FEEDER VOLTAGE DROP CHART
<br />This chart is based on a 320 Amp Demand (80% 400A), 208V 30
<br />Service from Utility Transformer to Panel L1,L2.
<br />WIRE TYPE AND SIZE FEET VD %VD
<br />UTILITY TRANSFORMER TO PANELS L1,L2
<br />(2) 3/0 75-C THW/THWN Wire = 100 2.13 1.02
<br />IChart indicates distance with load as shown. Should total distance exceed
<br />what is indicated it is to be brought to the attention of this Engineer.
<br />Verify location
<br />TC w/Owners Panel L2
<br />400A MLO
<br />120/208V
<br />TC 30 4 Wire
<br />SN
<br />Int. Lights
<br />2 Sets Ea. (3)3/0,3/ON,3G,2"C
<br />Bond to Concrete enclosed
<br />Steel Rebar (min. #4) in
<br />Bldg. Foundation per
<br />NEC 250.50
<br />RISER DIAGRAM
<br />NTS
<br />(3
<br />Z
<br />N
<br />U-)
<br />Q;
<br />M
<br />m -J
<br />Q
<br />J m
<br />�_
<br />Q J
<br />_J
<br />a)
<br />O
<br />�QLZ
<br />U�
<br />_J
<br />O
<br />-
<br />>_ L0CY-
<br />2
<br />CL
<br />UJ
<br />o W
<br />N
<br />(
<br />w
<br />o
<br />a
<br />�
<br />o
<br />CL
<br />O
<br />W�
<br />b
<br />(/) 0 Z
<br />w
<br />J W �
<br />rn
<br />00W
<br />PJ
<br />MJC)
<br />z
<br />J
<br />V) O
<br />U
<br />W
<br />I U
<br />I
<br />2
<br />=
<br />(n LA_ Q
<br />o
<br />Z (!') 0
<br />OJIW
<br />Z_
<br />f' w
<br />~
<br />0
<br />UDUN
<br />WJ�
<br />UUa
<br />Z
<br />coo
<br />04
<br />0 UJNU
<br />D
<br />UJ Q
<br />O
<br />o Z 0
<br />0-
<br />Z
<br />o
<br />�I
<br />m
<br />D
<br />Z
<br />Z
<br />of
<br />Z
<br />0
<br />Z
<br />W
<br />a
<br />o
<br />z
<br />�
<br />m
<br />�
<br />Z
<br />Z
<br />3
<br />O
<br />cZ�
<br />u7
<br />W
<br />N
<br />N
<br />v) a
<br />LLI
<br />U
<br />?
<br />;E2
<br />iWC2
<br />z
<br />W
<br />LU s2 8
<br />ti
<br />.
<br />J
<br />O
<br />�
<br />j
<br />Q
<br />w
<br />Zz
<br />i
<br />h
<br />�
<br />n
<br />
|