6529 Back Forty Lp - Laserfiche WebLink

Browse Search

C M STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP)- WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED WEEP SCREED HOLD 1/4" AIR GAP BETWEEN WEEP SCREED AND FLASHING COUNTER FLASHING CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL— FLASHING — PT 1X'i0 BLOCKING CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING CEMENT MORTAR---:, TILE ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 8" ROOF SHEATHING PER PLAN 3"=1'-0" 311= I 1-011 DET WALL SHEATHING PER PLAN STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP) SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED_ HOLD 1/4" AIR GAP BETWEEN WEEP SCREED AND FLASHING CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL PT 1X BLOCKING COUNTER FLASHING 00 PAN FLASHING 6" MIN�� ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 6"—� CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING TILE ROOF PER SPECS------___ 2X NAILER SECURELY FASTENED TO DECK ROOF SHEATHING NOTE: PER PLAN ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL HEAD WALL ROOF PER SPECS AYMENT 3LE OVER 3E iEATHING N 3E FASCIA HERED WRB TO OVER WRB ON :LOW )M BRAKE METAL WRAP �CKER ROD SLANT 'T MOULDING :F BRAKE METAL ON FRAME - 7/8" SAND FINISH STUCCO FURRING LATH ON 2- OF WATER RESISTIVE COMPLYING WITH 556, TYPE 1 (TYP) IEATHING PER PLAN RAKE WALL FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER FLASHING — STARTER STR HOLD 1/4" AIR GAP BETWEEN SIDING AND FLASHING COUNTER FLASHING CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL FLASHING PT 1X10 BLOCKING CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING CEMENT MORTAR TILE ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 8" ROOF SHEATHING PER PLAN -- 3"=1 V-0" HEAD WALL WALL SHEATHING PER P FIBER CEMENT SIDING PER ELEVATIONS SHINGLE WATER RESISTIVE BARRIER OVER FLASHING - STARTER STRIP HOLD 1/4" AIR GAP BETWEEN SIDING AND FLASHING CONT SELF ADHERED FLASHING TO LAP FLASHING AND TURN 3" UP WALL PT 1X BLOCKING - COUNTER FLASHING PAN FLASHING 6" MINA\ ROOF UNDERLAYMENT TO TURN UP BLOCKING MIN 6"---- CONT SELF ADHERED FLASHING TURN 3" UP BLOCKING TILE ROOF PER SPECS---_._ 2X NAILER SECURELY FASTENED TO DECK ROOF SHEATHING PER PLAN---------rn FLASHING REQUIREMENTS R730.1 GENERAL. EXTERIOR WALLS SHALL PROVIDE THE BUILDING WITH A WEATHER -RESISTANT EXTERIOR WALL ENVELOPE. THE EXTERIOR WALL ENVELOPE SHALL INCLUDE FLASHING AS DESCRIBED IN SECTION R703.4. R703.1 .1 WATER RESISTANCE. THE EXTERIOR WALL ENVELOPE SHALL BE DIMENSIONED AND CONSTRUCTED IN A MANNER THAT PREVENTS THE ACCUMULATION OF WATER WITHIN THE WALL ASSEMBLY BY PROVIDING A WATER-RESISTANT BARRIER BEHIND THE EXTERIOR CLADDING AS REQUIRED BY SECTION R703.2 AND A MEANS OF DRAINING TO THE EXTERIOR WATER THAT PENETRATES THE EXTERIOR CLADDING. R703.2 WATER RESISTIVE BARRIER. ONE LAYER OF NO.15 ASPHALT FELT, FREE FROM HOLES, COMPLY WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED WATER -RESISTIVE BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL EXTERIOR WALLS NO. 15 ASPHALT FELT SHALL BE APPLIED HORIZONTALLY, WITH THE UPPER LAYER LAPPED OVER THE LOWER LAYER NOT LESS THAN 2 INCHES. WHERE JOINTS OCCUR, FELT SHALL BE LAPPED NOT LESS THAN 6 INCHES. OTHER APPROVED MATERIALS SHALL BE INSTALLED IN ACCORDANCE WITH THE WATER -RESISTIVE BARRIER MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE NO.15 ASPHALT FELT OR OTHER APPROVED WATER -RESISTIVE BARRIER MATERIAL SHALL BE CONTINUOUS TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING APPENDAGES IN A MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN SECTION R703.1. R703.7.3 WATER -RESISTIVE BARRIERS WATER -RESISTIVE BARRIERS SHALL BE INSTALLED AS REQUIRED IN SECTION R703.2 AND, WHERE APPLIED OVER WOOD -BASED SHEATHING, SHALL INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE BARRIER WITH A PERFORMANCE AT LEAST EQUIVALENT TO TWO LAYERS OF GRADE D PAPER. THE INDIVIDUAL LAYERS SHALL BE INSTALLED INDEPENDENTLY SUCH THAT EACH LAYER PROVIDES A SEPARATE CONTINUOUS PLANE AND ANY FLASHING (INSTALLED IN ACCORDANCE WITH SECTION R703.4) INTENDED TO DRAIN TO THE WATER -RESISTIVE BARRIER IS DIRECTED BETWEEN THE LAYERS. EXCEPTION: WHERE THE WATER -RESISTIVE BARRIER THAT IS APPLIED OVER WOOD -BASED SHEATHING HAS A WATER RESISTANCE EQUAL TO OR GREATER THAN THAT OF 60-MINUTE GRADE D PAPER AND IS SEPARATED FROM THE STUCCO BY AN INTERVENING SUBSTANTIALLY NON -WATER -ABSORBING LAYER OR DESIGNED DRAINAGE SPACE. R703.4 FLASHING. APPROVED METAL FLASHING, VINYL FLASHING, SELF -ADHERED MEMBRANES AND MECHANICALLY ATTACHED FLEXIBLE FLASHING SHALL BE APPLIED SHINGLE -FASHION OR IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. METAL FLASHING SHALL BE CORROSION RESISTANT. FLUID -APPLIED MEMBRANES USED AS FLASHING SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S RAKE WALL INSTRUCTIONS, ALL FLASHING SHALL BE APPLIED IN A MANNER TO PREVENT THE ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE V1/P 17 COMPONENTS.BUILDING STRUCTURAL FRAMING SELF -ADHERED MEMBRANES USED AS FLASHING SHALL COMPLY WITH MMA 711. ALL EXTERIOR FENESTRATION PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT EXPANSION AND CONTRACTION, ASTMC1281, MMA 812, OR OTHER APPROVED STANDARD AS APPROPRIATE FOR THE TYPE OF SEALANT. FLUID -APPLIED MEMBRANES USED AS FLASHING IN EXTERIOR WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH. APPROVED FLASHINGS SHALL BE INSTALLED AT THE FOLLOWING LOCATIONS: 1. 1. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 FOR SUBSEQUENT DRAINAGE. MECHANICALLY ATTACHED FLEXIBLE FLASHINGS SHALL COMPLY WITH MMA 712. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE FOLLOWING: 1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING INSTRUCTIONS, OR FOR APPLICATIONS NOT ADDRESSED IN THE FENESTRATION MANUFACTURER'S INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING MANUFACTURER'S INSTRUCTIONS. WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PLAN FLASHING SHALL BE INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN FLASHING SHALL BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN FLASHING SHALL INCORPORATE FLASHING OR PROTECTION AT THE HEAD AND SIDES. 1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A REGISTERED DESIGN PROFESSIONAL. 1.3 IN ACCORDANCE WITH THE OTHER APPROVED METHODS. 1.4 IN ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA 200, FMA/WDMA 250, FMA/AAMA/WDMA 300 OR FMA/AAMA/WDMA 400. 2.2 AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH FRAME OR STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS. 3.3 UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL COPINGS AND SILLS. 4.4 CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM. 5.5 WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A WALL OR FLOGR ASSEMBLY OF WOOD -FRAME CONSTRUCTION. 6.6 AT WALL AND ROOF INTERSECTIONS. 7.7 AT BUILT-IN GUTTERS. THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL FLASHING AND WATERPROOFING METHODS TO BE USED. JUL 2 1 2023 Virtual Review Assist, Inc,/ rved plans Review completed and approved for compliance with the 2020 FBC 7th Edition by Debra Anne Klahr PX2300 .i--+ N O Cn > +, U L N (D O CL 0- y Cr Of O C= CID 0; 0- U U) N 70 0 V O •L c O O Q� cz$ LO O . � Cn (D O 0- Cn Q Q z z W J Cn c 0 n a) ca 0 L CL U O M m SHEET NO. WP 2.1