6610 Back Forty Lp - Laserfiche WebLink

Browse Search

TAPE EDGE OF HEAD WALL FLASHING STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP) WALL SHEATHING PER PLAN — SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED ------ WEEP SCREED------------- CONT SELF ADHERED FLASHING TURN 3" UP WALL- 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT SHINGLE ROOF PER SPECS — ROOF UNDERLAYMENT TO TURN UP WALL MIN 8"� ROOF SHEATHING PER PLAN----------- NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL 3 =1 -011 TAPE EDGE OF HEAD WALL FLASHING — STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP' WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED-------,.... WEEP SCREED ---- HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT -------- CONT SELF ADHERED FLASHING TURN 3" UP WALL----- CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 7CLOSURE STANDING SEAM METAL ROOF PER SPECS 'Ar=r,,T Tn ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN----------- 3 =1 -011 z 00 HEAD WALL STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP WALL SHEATHING PER PLAN-------______ SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED TAPE EDGE OF COUNTER FLASHING — WEEP SCREED 'H 'NG�— COUNTER FLASHING CONT SELF ADHERED U FLASHING TURN 73"UP WA L SHINGLE PER SPECS STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT E H u R I N S I IN 8'� P T B '(M ENT L ROOF UNDERLAYMENT TO LL TURN UP WALL MIN 8" T I ROOF SHEATHING PER PLAN NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP' TAPE EDGE OF RAKE WALL FLASHING SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED---� WEEP SCREED RAKE WALL STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT FIELD BEND PANEL UP 1 1/2" CONT BUTYL TAPE SEALANT PER 7PER 10 MANUFACTURER INSTALLATION INSTRUCTIONS 'Z'CLOSURE STANDING SEAM METAL ROOF PER SPECS -------- ROOF UNDERLAYMENT TO TURN UP WALL MIN 8"----� ROOF SHEATHING NOTE: PER PLANn�� ALL LATH AND LATH ATTACHMENTS TO BE CONT SELF ADHERED OUT OF CORROSION FLASHING TURN 3" UP WALL -RESISTANT MATERIAL HEAD WALL TAPE EDGE OF HEAD WALL FLASHING FIBER CEMENT SIDING PER ELEVATIONS — WALL SHEATHING PER PLAN - SHINGLE WATER RESISTIVE BARRIER OVER FLASHING -------- STARTER STRIP--------, 00 CONT SELF ADHERED FLASHING TURN 3" UP WALL 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT SHINGLE ROOF PER SPECS — ROOF UNDERLAYMENT TO TURN UP WALL MIN 8"— ROOF SHEATHING co PER PLAN -------------- RAKE WALL ROOF TO WALL WP12 it 1-011 3 =1 TAPE EDGE OF HEAD WALL FLASHING — FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER SHINGLE WATER RESISTIVE BARRIER OVER FLASHING MIN f STARTER STRIP — HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT CONT SELF ADHERED FLASHING TURN 3" UP WALL— CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS ;t 00 'Z'CLOSURE STANDING SEAM METAL 1�7111M I I ROOF PER SPECS --------- ROOF UNDERLAYMENT TO TURN UP WALL MIN 8` ROOF SHEATHING PER PLAN RAKE WALL WP14 ROOF TO WALL 3 If= 1 1-011 2� 2 00 HEAD WALL R. HEAD WALL FIBER CEMENT SIDING PER ELEVATIONS� WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER FLASHING--------_ TAPE EDGE OF COUNTER FLASHING STARTER STRIP ----------- COUNTER FLASHING----_ CONT SELF ADHERED FLASHING TURN 3" UP WALL SHINGLE PER SPECS------,. STEP FLASHING TiO EXTEND MIN 8" BEYOND UNDERLAYMENT--------- ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN --------- FIBER CEMENT SIDING PER ELEVATIONS — TAPE EDGE OF RAKE WALL FLASHING WALL SHEATHING PER PLAN — SHINGLE WATER RESISTIVE BARRIER OVER FLASHING MIN 8"-----_ STARTER STRIP --------- RAKE WALL STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT— FIELD BEND PANEL UP 1 1/2" CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z'CLOSURE ------- STANDING SEAM METAL ROOF PER SPECS --------- ROOF UNDERLAYMENT TO TURN UP WALL MIN ROOF SHEATHING PER PLANn!!!!-------� CONT SELF ADHERED FLASHING TURN 3" UP WALL FLASHING REQUIREMENTS R730.1 GENERAL. EXTERIOR WALLS SHALL PROVIDE THE BUILDING WITH A (D WEATHER -RESISTANT EXTERIOR WALL ENVELOPE. THE EXTERIOR WALL ENVELOPE _c_— U) —cu SHALL INCLUDE FLASHING AS DESCRIBED IN SECTION R703.4. > c- 0 R703.1 .1 WATER RESISTANCE. THE EXTERIOR WALL ENVELOPE SHALL BE DIMENSIONED CL AND CONSTRUCTED IN A MANNER THAT PREVENTS THE ACCUMULATION OF WATER 6 (D CL CU -0 WITHIN THE WALL ASSEMBLY BY PROVIDING A WATER-RESISTANT BARRIER BEHIND THE EXTERIOR CLADDING AS REQUIRED BY SECTION R703.2 AND A MEANS OF DRAINING TO 0) T5 �E THE EXTERIOR WATER THAT PENETRATES THE EXTERIOR CLADDING. 9-- :3 ca a) -0 0"-o R703.2 WATER RESISTIVE BARRIER. ONE LAYER OF NO.15 ASPHALT FELT, FREE FROM 0 a) HOLES, COMPLY WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED 0 C- 0 WATER -RESISTIVE BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL Li - Co 0 cu EXTERIOR WALLS NO. 15 ASPHALT FELT SHALL BE APPLIED HORIZONTALLY, WITH THE cz 0 > U) UPPER LAYER LAPPED OVER THE LOWER LAYER NOT LESS THAN 2 INCHES. WHERE E, a) 2 jOINTS OCCUR, FELT SHALL BE LAPPED NOT LESS THAN 6 INCHES. OTHER APPROVED cn MATERIALS SHALL BE INSTALLED IN ACCORDANCE WITH THE WATER -RESISTIVE !E cu N.02 -400 BARRIER MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE NO.15 ASPHALT FELT -0 U) OR OTHER APPROVED WATER -RESISTIVE BARRIER MATERIAL SHALL BE CONTINUOUS TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING APPENDAGES IN A MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN SECTION R703.1. R703.7.3 WATER -RESISTIVE BARRIERS WATER -RESISTIVE BARRIERS SHALL BE INSTALLED AS REQUIRED IN SECTION R703.2 AND, WHERE APPLIED OVER WOOD -BASED SHEATHING, SHALL INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE BARRIER WITH A PERFORMANCE AT LEAST EQUIVALENT TO TWO LAYERS OF GRADE D PAPER. THE INDIVIDUAL LAYERS SHALL BE INSTALLED INDEPENDENTLY SUCH THAT EACH LAYER I PROVIDES A SEPARATE CONTINUOUS PLANE AND ANY FLASHING (INSTALLED IN 00 ACCORDANCE WITH SECTION R703.4) INTENDED TO DRAIN TO THE WATER -RESISTIVE BARRIER IS DIRECTED BETWEEN THE LAYERS. EXCEPTION: WHERE THE WATER -RESISTIVE BARRIER THAT IS APPLIED OVER j .1 WOOD -BASED SHEATHING HAS A WATER RESISTANCE EQUAL TO OR GREATER THAN THAT OF 60-MINUTE GRADE D PAPER AND IS SEPARATED FROM THE STUCCO BY AN INTERVENING SUBSTANTIALLY NON -WATER -ABSORBING LAYER OR DESIGNED DRAINAGE SPACE. R703.4 FLASHING. APPROVED METAL FLASHING, VINYL FLASHING, SELF -ADHERED MEMBRANES AND MECHANICALLY ATTACHED FLEXIBLE FLASHING SHALL BE APPLIED SHINGLE -FASHION OR IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. METAL FLASHING SHALL BE CORROSION RESISTANT. FLUID -APPLIED MEMBRANES USED RAKE WALL AS FLASHING SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S W INSTRUCTIONS. ALL FLASHING SHALL BE APPLIED IN A MANNER TO PREVENT THE ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE WP13 BUILDING STRUCTURAL FRAMING COMPONENTS. SELF -ADHERED MEMBRANES USED AS FLASHING SHALL COMPLY WITH MMA 711. ALL EXTERIOR FENESTRATION PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT EXPANSION AND CONTRACTION, ASTMC1281, MMA 812, OR OTHER APPROVED STANDARD AS APPROPRIATE FOR THE TYPE OF SEALANT. FLUID -APPLIED MEMBRANES USED AS FLASHING IN EXTERIOR WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE I OF THE EXTERIOR WALL FINISH. APPROVED FLASHINGS SHALL BE INSTALLED AT THE FOLLOWING LOCATIONS: 1 . 1. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 FOR SUBSEQUENT DRAINAGE. MECHANICALLY ATTACHED FLEXIBLE FLASHINGS SHALL COMPLY WITH MMA 712. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE FOLLOWING: 00 1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING INSTRUCTIONS, OR FOR APPLICATIONS NOT ADDRESSED IN THE FENESTRATION MANUFACTURER'S INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING MANUFACTURER'S INSTRUCTIONS. WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PLAN FLASHING SHALL BE INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN 1. FLASHING SHALL BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN /\ FLASHING SHALL INCORPORATE FLASHING OR PROTECTION AT THE HEAD AND SIDES. 1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A 00 REGISTERED DESIGN PROFESSIONAL. 1.3 IN ACCORDANCE WITH THE OTHER APPROVED METHODS. 1.4 IN ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA 200, FMA/WDMA 250, FMA/AAMA/WDMA 300 OR FMAIAAMA/WDMA 400. 2.2 AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY j CONSTRUCTION WITH FRAME OR STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS. 3.3 UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL COPINGS AND SILLS. 4.4 CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM. 5.5 WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A WALL OR FLOOR ASSEMBLY OF WOOD -FRAME CONSTRUCTION. 6.6 AT WALL AND ROOF INTERSECTIONS. RAKE WALL 7.7 AT BUILT-IN GUTTERS. WP15 THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL FLASHING AND WATERPROOFING METHODS TO BE USED. JUL 2 12023 ."ia q1" Virtual Review Assist, Inc-�- 'Ins Revew completed and approved Ir compliance with the 2020 FEIC 7th Edition gebra Anne Klahr PX2300 cu 0 U-j c/) > 0 cj) C13 00 SHEET NO. WR 2.01