6648 Back Forty Lp - Laserfiche WebLink

Browse Search

.Q TAPE EDGE OF HEAD WALL FLASHING STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP) WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED — WEEP SCREED CONT SELF ADHERED FLASHING TURN 3" UP WALL- 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT SHINGLE ROOF PER SPECS — ROOF UNDERLAYMENT TO TURN UP WALL MIN 8"----, ROOF SHEATHING PER PLAN NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL HEAD WALL 1 -011 TAPE EDGE OF HEAD WALL FLASHING STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP WALL SHEATHING PER PLAN---, SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED---- HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT CONT SELF ADHERED FLASHING TURN 3" UP WALL_ CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 0_�1111� 'Z' CLOSURE STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP: WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED TAPE EDGE OF COUNTER FLASHING WEEP SCREED COUNTER FLASHING CONT SELF ADHERED FLASHING TURN 3" UP WALL SHINGLE PER SPECS STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN NOTE: ALL LATH AND LATH ATTACHMENTS TO BE OUT OF CORROSION -RESISTANT MATERIAL STUCCO ON FRAME - 7/8" 3-COAT SAND FINISH STUCCO ON SELF FURRING LATH ON 2- LAYERS OF WATER RESISTIVE BARRIER COMPLYING WITH ASTM E2556, TYPE 1 (TYP TAPE EDGE OF RAKE WALL FLASHING WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER WEEP SCREED WEEP SCREED RAKE WALL STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT FIELD BEND PANEL UP 1 1/2" —�\ CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z' CLOSURE \ STANDING SEAM METAL ROOF PER SPECS----- TAPE EDGE OF HEAD WALL FLASHING FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER FLASHING STARTER STRIP 00 CONT SELF ADHERED FLASHING TURN 3" UP WALL 18 GA HEAD WALL FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT AV SHINGLE ROOF PER SPECS ROOF UNDERLAYMENT TO d z TURN UP WALL MIN 8" ROOF SHEATHING 00 PER PLAN RAKE WALL - ROOF, TO WALL - WP12 3 =1 -0 TAPE EDGE OF HEAD WALL FLASHING FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER SHINGLE WATER RESISTIVE BARRIER OVER FLASHING MIN °' STARTER STRIP \ HEAD WALL TRIM FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT CONT SELF ADHERED FLASHING TURN 3" UP WALL CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS co 'Z' CLOSURE STANDING SEAM METAL ROOF PER SPECS ROOF UNDERLAYMENT TO STANDING SEAM METAL TURN UP WALL MIN 8"—� � ROOF PER SPECS ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN E�31�iIQ�]� y' ROOF SHEATHING NOTE: PER PLAN ALL LATH AND LATH ATTACHMENTS TO BE CONT SELF ADHERED OUT OF CORROSION FLASHING TURN 3" UP WALL -RESISTANT MATERIAL HEAD WALL ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN RAKE WALL ` WP14 - ROOFTO WALL - 3 =1 -0 , z 00 HEAD WALL HEAD WALL FIBER CEMENT SIDING PER ELEVATIONS WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER FLASHING — TAPE EDGE OF COUNTER FLASHING STARTER STRIP COUNTER FLASHING----_ CONT SELF ADHERED FLASHING TURN 3" UP WALL SHINGLE PER SPECS----- STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT ROOF UNDERLAYMENT TO TURN UP WALL MIN 8" ROOF SHEATHING PER PLAN FIBER CEMENT SIDING PER ELEVATIONS TAPE EDGE OF RAKE WALL FLASHING WALL SHEATHING PER PLAN SHINGLE WATER RESISTIVE BARRIER OVER FLASHING MIN 8"---,� STARTER STRIP RAKE WALL STEP FLASHING TO EXTEND MIN 8" BEYOND UNDERLAYMENT FIELD BEND PANEL UP 1 1/2" CONT BUTYL TAPE SEALANT PER MANUFACTURER INSTALLATION INSTRUCTIONS 'Z' CLOSURE STANDING SEAM METAL ROOF PER SPECS — ROOF UNDERLAYMENT TO TURN UP WALL MIN 8"--- ROOF SHEATHING PER PLAN CONT SELF ADHERED FLASHING TURN 3" UP WALL FLASHING REQUIREMENTS R730.1 GENERAL. EXTERIOR WALLS SHALL PROVIDE THE BUILDING WITH A Cv WEATHER -RESISTANT EXTERIOR WALL ENVELOPE. THE EXTERIOR WALL ENVELOPE SHALL INCLUDE FLASHING AS DESCRIBED IN SECTION R703.4. > j O O -Fr R703.1 .1 WATER RESISTANCE. THE EXTERIOR WALL ENVELOPE SHALL BE DIMENSIONED c O AND CONSTRUCTED IN A MANNER THAT PREVENTS THE ACCUMULATION OF WATER Q O , WITHIN THE WALL ASSEMBLY BY PROVIDING A WATER-RESISTANT BARRIER BEHIND THE C6 EXTERIOR CLADDING AS REQUIRED BY SECTION R703.2 AND A MEANS OF DRAINING TO � U U) THE EXTERIOR WATER THAT PENETRATES THE EXTERIOR CLADDING. O Ca cu .V5 R703.2 WATER RESISTIVE BARRIER. ONE LAYER OF NO.15 ASPHALT FELT, FREE FROM O O HOLES, COMPLY WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED O Q O WATER -RESISTIVE BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL O L — EXTERIOR WALLS NO. 15 ASPHALT FELT SHALL BE APPLIED HORIZONTALLY, WITH THE co CU OCo UPPER LAYER LAPPED OVER THE LOWER LAYER NOT LESS THAN 2 INCHES. WHERE O O EO JOINTS OCCUR, FELT SHALL BE LAPPED NOT LESS THAN 6 INCHES. OTHER APPROVED -U) CU MATERIALS SHALL BE INSTALLED IN ACCORDANCE WITH THE WATER -RESISTIVE %O BARRIER MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE NO.15 ASPHALT FELT I— -0 .0 U) Q OR OTHER APPROVED. WATER -RESISTIVE BARRIER MATERIAL SHALL BE CONTINUOUS TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING APPENDAGES IN A MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN SECTION R703.1. R703.7.3 WATER -RESISTIVE BARRIERS WATER -RESISTIVE BARRIERS SHALL BE INSTALLED AS REQUIRED IN SECTION R703.2 AND, WHERE APPLIED OVER WOOD -BASED SHEATHING, SHALL INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE BARRIER WITH A PERFORMANCE AT LEAST EQUIVALENT TO TWO LAYERS OF GRADE D PAPER. THE z INDIVIDUAL LAYERS SHALL BE INSTALLED INDEPENDENTLY SUCH THAT EACH LAYER PROVIDES A SEPARATE CONTINUOUS PLANE AND ANY FLASHING (INSTALLED IN m ACCORDANCE WITH SECTION R703.4) INTENDED TO DRAIN TO THE WATER -RESISTIVE BARRIER IS DIRECTED BETWEEN THE LAYERS. EXCEPTION: WHERE THE WATER -RESISTIVE BARRIER THAT IS APPLIED OVER WOOD -BASED SHEATHING HAS A WATER RESISTANCE EQUAL TO OR GREATER THAN THAT OF 60-MINUTE GRADE D PAPER AND IS SEPARATED FROM THE STUCCO BY AN INTERVENING SUBSTANTIALLY NON -WATER -ABSORBING LAYER OR 6„ DESIGNED DRAINAGE SPACE. R703.4 FLASHING. APPROVED METAL FLASHING, VINYL FLASHING, SELF -ADHERED MEMBRANES AND MECHANICALLY ATTACHED FLEXIBLE FLASHING SHALL BE APPLIED SHINGLE -FASHION OR IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. METAL FLASHING SHALL BE CORROSION RESISTANT. FLUID -APPLIED MEMBRANES USED AS FLASHING SHALL BE APPLIED IN ACCORDANCE WITH THE MANUFACTURER'S RAKE WALL WINSTRUCTIONS. ALL FLASHING SHALL BE APPLIED IN A MANNER TO PREVENT THE ENTRY OF WATER INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE WP 13 BUILDING STRUCTURAL FRAMING COMPONENTS. SELF -ADHERED MEMBRANES USED AS FLASHING SHALL COMPLY WITH MMA 711. ALL EXTERIOR FENESTRATION PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT EXPANSION AND CONTRACTION, ASTMC1281, MMA 812, OR OTHER APPROVED STANDARD AS APPROPRIATE FOR THE TYPE OF SEALANT. FLUID -APPLIED MEMBRANES USED AS FLASHING IN EXTERIOR WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH. APPROVED FLASHINGS SHALL BE INSTALLED AT THE FOLLOWING LOCATIONS: 1. 1. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL EXTEND TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 FOR SUBSEQUENT DRAINAGE. MECHANICALLY ATTACHED FLEXIBLE FLASHINGS SHALL COMPLY WITH MMA 712. FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE FOLLOWING: 1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING INSTRUCTIONS, OR FOR APPLICATIONS NOT ADDRESSED IN THE FENESTRATION MANUFACTURER'S INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING MANUFACTURER'S INSTRUCTIONS. WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PLAN FLASHING SHALL BE INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN FLASHING SHALL BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF THE EXTERIOR WALL FINISH OR TO THE WATER RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN FLASHING SHALL INCORPORATE FLASHING OR PROTECTION AT THE HEAD AV AND SIDES. 1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A 00 REGISTERED DESIGN PROFESSIONAL. 1.3 IN ACCORDANCE WITH THE OTHER APPROVED METHODS. 1.4 IN ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA 200, FMA/WDMA 250, FMA/AAMA/WDMA 300 OR FMA/AAMA/WDMA 400. 2.2 AT THE INTERSECTION OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH FRAME OR STUCCO WALLS, WITH JUL 2 1 PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS. 2OZ 3.3 UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL I COPINGS AND SILLS. 4.4 CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM. 5.5 WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A Virtual Rev ew Assist, Inc. WALL OR FLOOR ASSEMBLY OF WOOD -FRAME CONSTRUCTION. Plans Review con pleted and approved 6.6 AT WALL AND ROOF INTERSECTIONS. for compliance with he 2020 FBC 7th Edit o RAKE WALL 7.7 AT BUILT-IN GUTTERS. by Debra An a Klahr PX2300 THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL WP 15 FLASHING AND WATERPROOFING METHODS TO BE USED. C!) 0 O 0 �. W Q :z Z Q J d SHEET NO. WR 2.0 0 U 0 L L U O — I..L M� W I, -ij--,----TF- —i, ,t�m„W. --:Eflzri-LrrK-r;i I I i _ T- _ i �_ ,_. I i