|
THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />318" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />y:� •,: + �; ,� �.. MASONRY
<br />WINDOW BL)CK-
<br />;'.;,
<br />�, 2) SEALANT JOINT
<br />5) SEALANT FROM
<br />•; .' : ;c;; ;�'; •' INSIDE EDGE OF
<br />WINDOW FRAME
<br />: ; `; r' ► , WINDOWBUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE'
<br />6) TOOLED SFAL ANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME TC
<br />WINDOW BUCK ALL THE WAY
<br />AnOUND, INCLUDING SiLL.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />,IAMB. SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HouSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />314" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />"V" SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />WEATHER
<br />JE BARRIER &
<br />LARILY SECURE
<br />EXTERIOR
<br />SHEATHING
<br />WOOD FRAME CONS (H
<br />SELF -ADHERED FLASHI
<br />BY LAPPING DOWN --^ •.
<br />OVER RIM JOIST AND U10
<br />WALL BY 6 iN-
<br />WEATHER \�
<br />RESISITIVE \
<br />BARRIER SEAL TOPS l)F JQISTS
<br />UNDER DECKING
<br />ED FLASHING {SEE DETAIL WP07)
<br />HEAD FLASHING TIE-IN INSTRUXTIONS:
<br />1. Cut, fold up & temporarily secure weather
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head 2
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW W P01
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />EXTERIOR SHEATHING ----�
<br />REFER TO TECHNICAL
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />SELF ADHERED FLASHING-,
<br />OO NOT FLASH OVER
<br />BOTTOM NAILING
<br />FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />Detail Instructions
<br />Refer to the number marked as 0 in each detail that corresponds to the
<br />numbered items In the list of instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of comer may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as npc:PSsary
<br />NAILING FLANGE
<br />SELF -ADHERED FLASHING
<br />82
<br />W PO4
<br />M
<br />rt.r�rnlru rr-narnl�a 2\
<br />SELF -ADHERED FLASHING FwP07
<br />DECK JOIST
<br />2x FRAMEWALL---
<br />TILE FINISH---,
<br />1/2" DUROCK
<br />8" CMU --
<br />4" OR 8" CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED
<br />VINYL SHOWER PAN
<br />V-4" PER PLAN
<br />NEATi 1ER RFSISTIVE
<br />L3AHf;IE. R
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERFOR SHEATHINC; .
<br />3/4"-1" BEAD OF CC NSTR.
<br />ADHF. SIVE TO BE A�PLIED UNDER ---
<br />THRESHULU OF D( OR AND RETURN
<br />UP JAMB 6" US = L 1 101) NAII BRAND /
<br />OR EQUAL WEAT 11 R PRUL)i CAULKING 1
<br />SECTION -A (SL E DE: T 'wit WP02.)
<br />SELF-ADHEREOUlf. THING
<br />SEAL TOPS OF J )ISTS
<br />UNDER DECKINC,
<br />(SEE DETAIL WPi)T)
<br />SELF-ADHER
<br />SELF -ADHERED FLASHING
<br />E XTERiOR DOOR WITH DECK
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />SHOWER SEAT WP1 1
<br />SUBFLOOR
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />- SLOPE
<br />0.3 in: 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />��.•� F3FAL1 or cc�NSTF; (0.6 cm : 30.5 cm) include flashing as described in Section R703.4-
<br />ADHESiVE TUBE APPLIFDUNDEFt -SELF-ADHEREt� FLASHING
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6°. USE LIQUID R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of water
<br />NAIL BRAND OR ECAJAL WEAi HE EXTERIOR
<br />PROOF CAULKING ----- iI -CEMT. FIN. within the wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means of
<br />��- SELF -ADHERED FLASHING BUILDING PAPER
<br />draining to the exterior water that penetrates the exterior cladding.
<br />-� WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other
<br />` approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2 inches. Where pints occur, felt shall be lapped not less than 6 inches. Other
<br />approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The No.15 asphalt
<br />felt or other a roved water -resistive barrier material shall b cont'n o t th t f II d t t d t tr t' d b Id
<br />- RiM JOIST pp e i u us a e op o Wa s an ermine e a pens a Ions an ul Ing
<br />appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based
<br />sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper_ The
<br />2 :.
<br />- -�' 2 individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in
<br />accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING
<br />W pQ2 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER W P03 Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance
<br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />�* MECHANICALLY FASTEN IF RUBBERIZED ASPHALT substantially nonwater-absorbing layer or designed drainage space.
<br />RUBBERIZED 1
<br />NEEDED IN CORNERS ADHESIVE 1
<br />INSTALL sEl F-ADHERED ASPHALT ADHESIVE
<br />F I A SHING ,IANIR A HEAD THROUGH SELF -ADHERED R703.4 Flashing. Approved metal flashing, vinyl flashing, self-adhsred membranes and mechanically attached flexible flashing shall be applied
<br />I't.A, HIND ',I E FLASHING f-SELF-ADHERED FLASHING shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied membranes
<br />F-LAM;LD WIN0L )w7
<br />I g 9 PP
<br />(SEE DETAIL wF'O1) used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to prevent the
<br />SCORED entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />RELEASE PAPER Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />SELF•AOHEREDFLASHING, �`e J3L C;r+F FCn:.i1rJO SCORE the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />RELEASE P4PFR rof.Ap s
<br />EXTEND A MINIMUM i' AO:YESWE As SHOWN) contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />VERTICALLY FROM
<br />Id BOTTOM OF flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />THRESHOLD shall be installed at the following locations:
<br />1.1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />- finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible fleshings
<br />\� shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />2 following:
<br />5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />�4) manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details are
<br />1 S not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for subsequent
<br />drainage. Openings using pan flashing shall Incorporate flashing or protection at the head and sides.
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />('� SELF -ADHERED FLASHING 1.3 1.3. In accordance with other approved methods.
<br />W P05 INSIDE CORNER WP06 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/ `DMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />Ground - 3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />4.4.Continuously above all projecting wood trim.
<br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />1 / . 6.6.At wall and roof intersections.
<br />--- Watw Resistant Barrier 7. 7.At built-in Gutters.
<br />'LF-ADHERED FLASHING -I
<br />ITCH
<br />HERFD FLASHING ^�
<br />l I l
<br />;2
<br />i4
<br />W P08
<br />PLASTER STOP •f
<br />CONTINUOUS BACKER --.-
<br />ROD & SEALANT
<br />�A
<br />;TRIP OF SAF
<br />DRAINAGE PLAN
<br />r�
<br />4, •
<br />Foundation Wall, ,
<br />.a
<br />FOUNDATION WEEP SCREED
<br />i
<br />E WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />-
<br />WRAP DP WRB ONTO
<br />y
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />`y
<br />i i-AN(A.''AS AN AIR
<br />RARRIL'R
<br />I j
<br />I , C
<br />3-1rt INCH FLANGE
<br />' jlq
<br />E-- THII, GAP IS A RESULT OF
<br />NATURAI SHRINKAGE.
<br />LX) NOT SEAL
<br />DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />LEGEND
<br />Lath
<br />- - Sheathing
<br />Stucco
<br />oK
<br />Mtge] �161
<br />SELF ADHERED FLASHING (SAF) o 0
<br />DRAINAGE PLANE (UP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANi BARRIER- - -
<br />Sr.LF FURRING (SF) LATH -'--
<br />PLASTER ACCESSORY
<br />SIIL.A It0NG. TISB', Pt YWOOD, DENSGiASS
<br />(STER STOP
<br />NTINUOUS BACKLR ROD
<br />EALANT
<br />ME:NTITIOUS FINISH
<br />STRUCTURAL FRAMINI-r
<br />STnUC`T1IRAL SHEATHIW',
<br />STRIP OF SAF
<br />UkAINACIF. PLANE WRB
<br />BOND BREAK WRB
<br />SF L-ATI.1
<br />WP10
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />-7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottorn of
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1 /2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />2 1 2023
<br />iew Assist. Inc.
<br />1pleted and appl
<br />the 2020 FBC 7tl
<br />,le Klahr PX2300
<br />W
<br />-0
<br />>
<br />tU
<br />o
<br />ao
<br />a
<br />o
<br />.�
<br />V
<br />Co
<br />cQ
<br />0
<br />o
<br />a
<br />o
<br />t`
<br />0
<br />to
<br />p
<br />>
<br />o
<br />.,c
<br />U)
<br />Q
<br />cr)
<br />■
<br />CU
<br />V
<br />CU
<br />>
<br />L.
<br />■
<br />CL
<br />Q.
<br />-E"r
<br />o
<br />�
<br />o
<br />0.
<br />Cn
<br />ca
<br />CIO
<br />LLJ
<br />Q
<br />Z
<br />Z
<br />Q
<br />•.J
<br />CL
<br />SHEET NO.
<br />WP1
<br />no
<br />
|