Laserfiche WebLink
FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />---- --— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — ---- <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />25-SH 25-SH Ci 12 FLASHING <br />14.0 <br />----------------------------- —�_--- — ---- <br />l <br />------------------ <br />CJ/WEEP <br />35-SH <br />R... •1--------------------------- L--1- <br />6068 SGD <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />REAR ELEVATION - B <br />SCALE: 1/4" = 1'-0" <br />9'-0" RIDGE VENT <br />12 ��- <br />r � <br />r , 1 <br />I i <br />FIBEREGLASS SHINLGE INSTALLED;T r 1 =i _, 1 17 J - I` AS PER PER MANUFACTURER -I 1 - - -i _ - -1. l ? -1- ,-T_IF i <br />l ,_ � I I A , I i I <br />TT SPECIFICATIONS <br />i <br />EXTERIOR <br />PLASTER ON <br />FRAME 1 H3-SH FLASHING <br />24 SH <br />12 CJ CJ 12 <br />----- 4-01— 14.0 <br />CJ/WEEP CJ <br />2'-0" <br />F-1 H3-SH <br />----1--L---__J__-_1---------------------------------------------------L------------------------------------------I--_FI <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />LEFT ELEVATION - B <br />SCALE: 1/4" = V-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-1/2" long, <br />16 gage staples, spaced in accordance with ASTM C1063 or <br />C1787, or as otherwise approved. (Refer to sheet SN1 for the <br />engineered method for Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />c� <br />ca <br />© <br />dLU <br />`1 W <br />CD <br />G M CJ N <br />LA- <br />y 10 G7 � <br />y N O ff7 <br />4. N <br />ar <br />ar <br />3� <br />d <br />�.G,>, <br />d �C= <br />E <br />w ca <br />C"7 <br />N <br />O <br />N <br />CD <br />0 <br />C <br />o <br />C,, "i' <br />To the best of the Engineers knowledge, Information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residentlal 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions <br />of the drawing pages bearing <br />Engineers signature and seal. <br />$ $ Ig�� <br />LL <br />M <br />(nhh� LL <br />M a <br />fj <br />Q) s} 411 <br />4 a �c <br />13 <br />u- <br />Z <br />r�p <br />t a' 0 <br />W <br />Z <br />CO &g gZ <br />to <br />i <br />Z <br />N M Q <br />oo❑ <br />W <br />z <br />o <br />z OD <br />z o <br />Y <br />f%i <br />z v <br />4C-D <br />•V <br />—� <br />O <br />c <br />V)LU <br />U <br />-i <br />C.) <br />x <br />t_-_ y <br />Q N <br />s0 <br />" E <br />;S <br />O u <br />Z O <br />0 <br />k� <br />oa <br />I. M <br />::, <br />a <br />Mo <br />WZ <br />o0 <br />°a <br />Z <br />c, <br />ro <br />$b <br />wg <br />�W <br /><� <br />m0 <br />Z <br />W0 <br />d�� <br />� <br />N <br />�s <br />Mill!�k <br />° <br />2 0 <br />J <br />>U) <br />O <br />rn <br />c� <br />L <br />T <br />CID <br />T <br />N <br />cL <br />N <br />Q <br />CT <br />g <br />�- <br />-�' <br />LO <br />O <br />`'00 <br />O <br />LL <br />-0 <br />.� <br />cco N <br />O <br />N <br />LO <br />T <br />Q <br />9Z. � <br />T <br />E <br />�• <br />M <br />r <br />z° <br />c <br />E T <br />ai <br />a <br />U � <br />Q pre <br />°i <br />JOB <br />NO: <br />23-03653 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.2 <br />