6900 Gall Blvd (4) - Laserfiche WebLink

Browse Search

PROPOSED WORK KEY NOTES NEW VINYL PLANK FLOORING 56"X9" THROUGHOUT UNLESS OTHERWISE NOTED. REFER TO FINISHES SCHEDULE ON ID-02 FOR ADDITIONAL INFORMATION ❑2 MINOR FLOOR PREPARATION AND LEVELING AS REQUIRED NEW 4" VINYL BASEBOARD THROUGHOUT UNLESS OTHERWISE NOTED. REFER TO FINISHES SCHEDULE ON ID-02 FOR ADDITIONAL INFORMATION ® NO CHANGE IN ELEVATION 0 REPAIR—PATCH/SAND/PAINT PARTITION IF REQUIRED AS A RESULT OF DEMOLITION. FINISH TO MATCH EXISTING © EXISTING FINISH FLOOR TO REMAIN IF IN GOOD CONDITION OTHERWISE REPLACE IT WITH NEW FLOORING TO MATCH THE REST F7 NEW DESK BY FURNITURE PROVIDER. FURNITURE FINAL SELECTION TO BE DETERMINED BY OWNER ® NEW FURNITURE MODULES (SEATING) BY OTHERS. FURNITURE FINAL SELECTION TO BE DETERMINED BY OWNER 09 EXISTING BASEBOARD TO REMAIN IF EXISTING FLOORING IS TO REMAIN OTHERWISE REPLACE IT WITH NEW BASEBOARD TO MATCH THE REST 10 EXISTING VIEWING WINDOW TO BE FRAMED IN AND FINISHED WITH 1/2" G.W.B. ON BOTH SIDES TO MATCH EXISTING WALL FINISH 11 INFILL OPENING WITH 1/2" G.W.B. ON METAL STUDS TO MATCH EXISTING WALL FINISH 12 NEW MILLWORK BUILT—IN CABINETS WITH COUNTERTOP FOR RECEPTION STORAGE BY OTHERS 13 LINES DENOTES LIMIT OF NEW FINISH FLOOR 14 PROVIDE ADA COMPLIANT THRESHOLD IF REQUIRED AT DISSIMILAR FINISH FLOOR TRANSITION. THRESHOLD SHALL BE 1/2" HIGH MAXIMUM. FAC 404.2.5/ FAC 302 AND 303 15 NEW MODULAR MILLWORK DESK/ COUNTER BY OTHERS. REFER TO ID PLANS FOR DETAILS. FINISH TO BE DETERMINED BY OWNER 16 PRINTER COMPARTMENT BELOW COUNTER 17 NEW G.W.B./METAL STUDS PARTITION. REFER TO WALL TYPES FOR DETAILS 18 CONTRACTOR TO PROVIDE BLOCKING AT BULKHEADS AND INTERIOR PARTITIONS FOR WALL MOUNT TVs AND CURTAINS 19 ADD (1) ADDITIONAL LAYER OF 1/2" GYPSUM BOARD TO EXISTING GYPSUM INTERIOR PARTITIONS THROUGHOUT ENTIRE MAMMO ROOM FOR SHIELDING. RADIATION PROTECTION SHALL BE DESIGNED AND APPROVED BY OWNER LICENSED PHYSICIST F261 PROVIDE STAINLESS STEEL TRANSITION STRIP AT DOORWAY AT CHANGE OF DIRECTION IN FLOOR. REFER TO ID DRAWINGS FOR FLOORING PATTERN 21 CLEAN, PREP AND PAINT ALL DOORS AND FRAMES THROUGHOUT PER INTERIOR FINISHES SCHEDULE ON ID-02. PAINT FINAL SELECTION TBD BY OWNER 22 NEW (18"X18") LOCKER BY FURNITURE COMPANY. COLOR AND FINISH TO BE DETERMINED BY OWNER 23 NEW ADA COMPLIANT LOCKER BY FURNITURE COMPANY. LOCKER SHALL COMPLY WITH FAC 803. COLOR AND FINISH TO BE DETERMINED BY OWNER 24 THE UNOBSTRUCTED HIGH SIDE REACH SHALL BE 48 INCHES MAXIMUM AND THE LOW SIDE REACH SHALL BE 15 INCHES MINIMUM A.F.F. 25 NEW BENCH BY FURNITURE COMPANY. COLOR AND FINISHES TO BE DETERMINED BY OWNER 26 NEW ADA COMPLIANT BENCH BY FURNITURE COMPANY. BENCH SHALL BE PROVIDED PER FAC 803.4. BENCH SHALL HAVE SEAT THAT ARE 42 INCHES LONG MINIMUM AND 20 INCHES DEEP MINIMUM AND 24 INCHES MAXIMUM PER FAC 903.3 27 TOP OF THE BENCH SEAT SURFACE SHALL BE 17 INCHES MINIMUM AND 19 INCHES MAXIMUM A.F.F. PER FAC 903.5 28 DOOR MOUNTED COAT HOOK AT 48" A.F.F. ON CENTER. CENTER HOOK HORIZONTALLY WITH DOOR WIDTH. TYP. AT ALL RESTROOMS AND CHANGE ROOMS 29 5'-0" (60") DIAMETER TURNING CIRCULAR SPACE FAC 304.3.1 30 30"X48" CLEAR FLOOR SPACE FORWARD APPROACH PER FAC 305 31 30"X48" CLEAR FLOOR SPACE PARALLEL APPROACH PER FAC 305 32 MANEUVERING CLEARANCE AT MANUAL SWINGING DOOR PER FAC 404.2.4.1 33 3'-0" HIGH MAXIMUM A.F.F. FAC 904.4.1 34 PREPARE SURFACES, PRIME AND PAINT ALL INTERIOR PARTITIONS AND HARD CEILINGS PER INTERIOR FINISHES DRAWING AND SCHEDULE ON ID-02 35 ACCENT PAINT COLOR SPECIFICATION AND LOCATION PER INTERIOR FINISHES DRAWING AND SCHEDULE ON ID-02 36 EXISTING G.W.B. LOW PARTITION TO BE FRAMED AND FINISHED WITH 1/2" G.W.B. UP TO EXISTING HEADER IN ORDER TO ENCLOSE ROOM AS INDICATED IN PLAN WITH HATCH 37 NEW WALL HUNG 1/4" CLEAR GLASS MIRROR WITH POLISHED EDGES IN ALL CHANGE ROOMS ABOVE BENCH. REFER TO FINISHES SCHEDULE ON ID-02 38 NEW TOILET PAPER DISPENSER AT ALL RESTROOMS AS PER AKUMIN STANDARDS. DISPENSER SHALL NOT BE OF A TYPE THAT CONTROLS DELIVER OR THAT DOES NOT ALLOWED CONTINUOUS PAPER FLOW FAC 604.9.6 39 TOILET PAPER DISPENSER SHALL BE 7" MINIMUM AND 9" MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THE CENTER LINE OF THE DISPENSER 40 THE OUTLET OF THE DISPENSER SHALL BE 15" MINIMUM AND 48" MAXIMUM ABOVE THE FINISH FLOOR AND SHALL NOT BE LOCATED BEHIND GRAB BARS 41 NEW WALL MOUNTED WASTE PAPER BASKET AT ALL RESTROOMS AS PER AKUMIN STANDARDS. TOP OF BASKET AT 48" MAXIMUM AND LOW SIDE 15" MINIMUM A.F.F. 42 NEW SOAP DISPENSER AT ALL RESTROOMS AS PER AKUMIN STANDARDS. DISPENSER TO BE MOUNTED 44 INCHES ON CENTER A.F.F. 43 NEW TOWEL PAPER DISPENSER AT ALL RESTROOMS AS PER AKUMIN STANDARDS. TOP OF DISPENSER AT 48 INCHES MAXIMUM A.F.F. 44 CONTRACTOR TO SUBMIT SHOP DRAWINGS TO INTERIOR DESIGNER FOR REVIEW AND APPROVAL PRIOR FABRICATION EXISTING TOP TRACT STRUCTURAL DECK EXISTING EXISTING TOP TRACT STRUCTURAL DI MARK LOCATION INTERIOR E!! SCHEDULE DOOR FRAME REMARKS ROOM NAME WIDTH HEIGHT THICK MATERIAL FINISH MATERIAL FINISH 1 HALL BY RECEPTION 3'-0" 6-8" 1 3/" HOLLOW METAL PAINTED METAL PAINTED 2 CLOSET (2) 2'-6" 6-8" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 3 WAITING AREA (2) 3'-0" T-0" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 4 STORAGE ROOM 3'-0" T-0" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 5 DEXA ROOM 3'-0" T_0" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 6 OFFICE 3'-0" T-0" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 7 ELECTRICAL ROOM 3`-0" 6'-8" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED 8 CHANGE ROOM 1 3'-0" 6-8" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED PRIVACY LATCH 9 CHANGE ROOM 2 3'-0" 6'-8" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED PRIVACY LATCH 10 MAMMOGRAM ROOM 3`-O" 6-8" 1 3/4" HOLLOW METAL PAINTED METAL PAINTED SEE NOTES 3, 4, 5, 6, 7 1. FINISH PER FINISHES SCHEDULE ON ID DRAWING ID-02 2_ STYLE AND HARDWARE TO MATCH EXISTING 3_ DOOR SHIELDING: DOOR AND DOOR FRAME SHOULD BE EQUIVALENT TO 1 MILLIMETER OF STEEL 4_ DOOR AND DOOR FRAME SHALL HAVE EQUAL OR EQUIVALENT SHIELDING VALUE AS THAT REQUIRED IN THE WALL. IN WHICH IT IS INSTALLED 5_ DOOR AND DOOR FRAME SHIELDING VALUE SHALL BE DESIGNED AND APPROVED BY A LICENSED PHYSICIST 6_ DOOR LOCKSET HARDWARE SHIELDING SHALL BE DESIGNED AND APPROVED BY A LICENSED PHYSISCIST 7_ GAP BETWEEN THE BOTTOM OF DOOR AND THE FINISH FLOOR SHOULD BE KEPT AS SMALL AS POSSIBLE. THRESHOLD, IF REQUIRED, TO BE DETERMINED BY A LICENSED PH To the best of the Architect's knowledge these plans comply with the minimum standards of the applicable codes and life safety standards as determined in accordance with Chapter 553 and 663 of the Florida statutes For Construction ,Review Set Not for Construction ® Permit Set Bid Set F1 Record Set All designs, details and drawings indicated and represented are for use on and in conjunction with the specified project, the designs and drawings are the property of the Architect and shall not be reproduced in whole or in part without the written permission of M3o Architecture, Inc No. I Date Description Project Name PROPOSED FLOOR PLAN SCALE: 1 /4"=1'-0" AKUMIN - ZEPHYRHILLS INTERIOR ALTERATION 6900 GALL BLVD ZEPHYRHILLS, FL 33542 Project Team W11 GENERAL NOTES: CONTRACTOR SHALL MAINTAIN EXISTING FINISH FLOOR ELEVATION IN ORDER FOR NEW FINISH FLOOR TO BE FLUSH AT ALL TRANSITIONS AND DOORS ALL DIMENSIONS ARE GIVEN FROM FINISHED SURFACES UNLESS OTHERWISE NOTED CEILING HEIGHT IS INDICATED ON THESE PLANS AND MUST BE AS MAINTAINED AS STATED ALL NEW FINISH FLOOR SURFACES SHOULD BE LEVELED. THE FLOOR AREA UNDER THE EQUIPMENT BASES, EXTENDING 3'-0" IN ALL DIRECTIONS AROUND EACH BASE, MUST BE LEVEI ED, USING A CARPENTER'S LEVEL OF APPROPRIATE LENGTH, TO WITHIN 1/16" MAMMOGRAM ROOM SHIELDING SHALL BE DESIGNED AND APPROVED BY A LICENSED PHYSICIST OWNER/CONTRACTOR SHALL EMPLOY A REGISTERED PHYSICIST TO SPECIFY RADIATION PROTECTION 11401 SW 40th Street, Suite 301 Miami, FI 33165 t: (786) 275-4635 3 c: (305) 905-4657 ARCHITECTUREe. mtrejo@m3oarchitecture.com www.m3oarchitecture c o m AA26003093 AR97374 NOTES: WALKING SURFACES SHALL HAVE A SLIP —RESISTANT SURFACE AND BE SECURELY ATTACHED. FBC 1003.4 FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, AND SLIP RESISTANT FBC ACCESSIBILITY 302.1 THRESHOLDS AT DOORWAYS SHALL NOT EXCEED 1/2 INCH (12.7 mm) ABOVE FINISHED FLOOR OR LANDING. RAISED THRESHOLDS AND FLOOR LEVEL CHANGES GREATER THAN 1 /4 INCH (6.4 mm) AT DOORWAYS SHALL BE BEVELED WITH A SLOPE NOT GREATER THAN ONE UNIT VERTICAL IN TWO UNITS HORIZONTAL (50—PERCENT SLOPE) FBC 1010.1.7/ FBC ACCESSIBILITY 303.3/404.2.5 THE RUNNING SLOPE OF WALKING SURFACES SHALL NOT BE STEEPER THAN 1:20. THE CROSS SLOPE OF WALKING SURFACES SHALL NOT BE STEEPER THAN ONE UNIT VERTICAL IN 48 UNITS HORIZONTAL (1:48) (2—PERCENT SLOPE) (FBC ACCESSIBILITY 403.3 INTERIOR FLOOR FINISH MATERIALS SHALL COMPLY WITH FBC SECTION 804.4.2 Sheet Title I Sheet No. PROPOSED FLOOR PLAN, SCHEDULE, A=3 GENERAL NOTES AND KEY NOTES