|
ELECTRICAL SYMBOL LEGEND
<br />GENERAL ELECTRICAL NOTES & SPECIFICATIONS
<br />1. THE "GENERAL CONDITIONS OF THE CONTRACT", CURRENT EDITION, PUBLISHED IN STANDARD FORM BY
<br />THE AMERICAN INSTITUTE OF ARCHITECTS SHALL BE PART OF THIS CONTRACT.
<br />2. IT IS NOT THE INTENT OF THESE PLANS AND SPECIFICATIONS TO SHOW EVERY AND ALL DETAILS OF
<br />CONSTRUCTION. THE CONTRACTOR SHALL FURNISH AND INSTALL ALL ITEMS REQUIRED FOR A COMPLETE
<br />ELECTRICAL INSTALLATION IN PROPER WORKING ORDER.
<br />3. ALL WORK AND MATERIALS SHALL BE IN FULL ACCORDANCE WITH THE LATEST ADOPTED EDITION OF THE
<br />FLORIDA BUILDING CODE (2020) NEC 2017 AND THE LATEST STATE AND LOCAL CODES THAT APPLY.
<br />4. THE CONTRACTOR SHALL TAKE OUT PERMITS, PROCURE CERTIFICATES AND PAY ALL FEES CONNECTED
<br />WITH HIS WORK.
<br />5. BIDDERS SHALL VISIT THE SITE AND FAMILIARIZE THEMSELVES WITH ALL CONDITIONS SURROUNDING THE
<br />WORK. IT SHALL BE THE RESPONSIBILITY OF THE BIDDERS TO VISIT THE SITE OF WORK AND ACQUAINT
<br />THEMSELVES WITH ALL AVAILABLE INFORMATION REGARDING THE EXISTING FACILITIES.
<br />FAILURE OF THE BIDDERS TO SO INFORM THEMSELVES OF EXISTING CONDITIONS AND TO INCLUDE IN
<br />THEIR PROPOSALS A SUM SUFFICIENT TO COVER SAME WILL NOT ENTITLE THEM TO AN EXTRA.
<br />6. THE CONTRACTOR IS REFERRED TO THE ARCHITECTURAL PLANS AND SPECIFICATIONS. SUCH PLANS AND
<br />SPECIFICATIONS ARE CONTRACT DOCUMENTS.
<br />7. DRAWINGS ARE DIAGRAMMATIC AND INTENDED TO SHOW APPROXIMATE LOCATIONS OF ALL ELECTRICAL
<br />ITEMS. EXACT CONDUIT ROUTING SHALL BE DETERMINED IN THE FIELD, UNLESS OTHERWISE NOTED (LION).
<br />8. CONTRACTOR SHALL SUBMIT REQUESTS FOR SUBSTITUTION IN WRITING TO THE ENGINEER, 10 WORKING
<br />DAYS PRIOR TO BIDDING DATE.
<br />9. THE CONTRACTOR SHALL SUBMIT SHOP DRAWINGS FOR APPROVAL FOR ALL EQUIPMENT AND MATERIALS.
<br />SUBMIT A MINIMUM OF FOUR SETS TO THE A/E.
<br />10. THIS CONTRACTOR SHALL TOUCH UP OR REFINISH THE FACTORY FINISH OF EQUIPMENT MARRED DURING
<br />DURING SHIPMENT OR INSTALLATION. THE CONTRACTOR SHALL BE RESPONSIBLE TO REPAIR TO ORIGINAL
<br />CONDITIONS ANY AND ALL DAMAGES TO BUILDING SURFACES, EQUIPMENT, AND FURNISHING CAUSED
<br />DURING THE PERFORMANCE OF WORK.
<br />11. THE ELECTRICAL INSTALLATION SHALL MEET THE APPROVAL OF THE ENGINEER BEFORE ACCEPTANCE BY
<br />THE OWNER.
<br />12. THE CONTRACTOR SHALL BE A STATE LICENSED CONTRACTOR.
<br />13. THE ENTIRE INSTALLATION SHALL BE PERFORMED UNDER DIRECT SUPERVISION OF A LICENSED MASTER
<br />ELECTRICIAN IN A FIRST CLASS WORKMANLIKE MANNER. IT SHALL BE THE RESPONSIBILITY OF THE
<br />CONTRACTOR TO PROVIDE ALL LABOR, MATERIALS AND SUPERVISION NECESSARY TO ACCOMPLISH THE
<br />WORK AS SHOWN AND/OR NOTED ON THE DRAWINGS.
<br />14. ELECTRICAL WORK SHALL NOT INTERFERE WITH CLEARANCES REQUIRED FOR GENERAL AND MECHANICAL
<br />CONSTRUCTION. SHOULD ELECTRICAL WORK BE INSTALLED WHICH INTERFERES WITH THE WORK OF
<br />OTHER TRADES, SUCH WORK SHALL BE CORRECTED AT NO COST TO THE OWNER. THE CONTRACTOR
<br />SHALL SUBMIT (4 COPIES) EQUIPMENT LAYOUT OF ALL ELECTRICAL SPACES, ROOMS, ETC., TO
<br />ARCHITECT FOR APPROVAL PRIOR TO ORDERING EQUIPMENT OR INSTALLING CONDUITS, ETC.,
<br />LAYOUTS SHALL CONSIST OF PLAN VIEWS (SCALED AT 1/2" = V-0") AND ELEVATIONS (DIMENSIONED)
<br />FOR EACH SPACE, ROOM, ETC., .AND SHALL INCLUDED EQUIPMENT FURNISHED BY OTHER TRADES.
<br />15. GROUNDING SHALL COMPLY WITH THE NATIONAL ELECTRICAL CODE (ARTICLE 250) AND REQUIREMENTS
<br />OF THE INSPECTING AUTHORITY. ALL CONNECTIONS TO GROUND RODS SHALL BE MADE WITH UL
<br />APPROVED ACCESSIBLE GROUND CLAMPS, UNLESS OTHERWISE NOTED.
<br />16. UPON COMPLETION OF WORK, THIS CONTRACTOR SHALL REMOVE ALL RUBBISH CAUSED BY HIS WORK
<br />AND SHALL THOROUGHLY CLEAN ALL ELECTRICAL EQUIPMENT.
<br />17. ALL WORK SHALL BE GUARANTEED FREE FROM DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF
<br />FINAL ACCEPTANCE.
<br />18. ALL ITEMS OF ELECTRICAL EQUIPMENT ASSOCIATED WITH THE CONTROL OF ELECTRICAL CIRCUITS AND
<br />APPARATUS SHALL BE IDENTIFIED..
<br />19. ALL POWER AND LIGHTING CIRCUIT WIRING SHALL BE COLOR CODED AS FOLLOWS:
<br />120 208V. 277 480V.
<br />PHASE "A" - BLACK PHASE "A" - BROWN
<br />PHASE "B" - RED PHASE "B" - ORANGE
<br />PHASE "C" - BLUE PHASE "C" - YELLOW
<br />NEUTRAL - WHITE NEUTRAL - GRAY
<br />GROUND - GREEN GROUND - GREEN
<br />20. ALL CONDUCTORS SHALL BE COPPER, 60OV. #12 AND SMALLER, SOLID TYPE THWN/THHN;
<br />#10 AND LARGER, STRANDED TYPE THWN/THHN.
<br />21. ALL CONDUCTORS FOR POWER LIMITED CABLES SHALL COMPLY WITH ARTICLES 725 & 760 OF N.E.C.
<br />LATEST EDITION.
<br />22. NOMINAL MOUNTING HEIGHT OF DEVICES IN EXPOSED CONCRETE BLOCK, TILE OR BRICK WALLS SHALL ALL
<br />OCCUR WITHIN A STRUCTURAL COURSE. A MIN. AMOUNT OF BLOCK, TILE OR BRICK WALLS SHALL BE CU'i.
<br />23. ALL ELECTRICAL EQUIPMENT AND DEVICES SHALL BE INDUSTRIAL GRADE, HEAVY-DUTY, AND U.L. LISTED
<br />UNLESS SPECIFIED OTHERWISE. ALL ELECTRICAL EQUIPMENT, DEVICES, WIRE, ETC., SHALL BE LISTED,
<br />FOR THE INTENDED USE, WITH UNDERWRITER'S LABORATORIES INC. (UL), WHERE STANDARDS HAVE BEEN
<br />ESTABLISHED BY UL. AS A MINIMUM, ALL EQUIPMENT SHALL MEET APPLICABLE STANDARDS, FOR THE
<br />TYPE OF EQUIPMENT AND THE INTENDED USE, OF THE FOLLOWING.
<br />A. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)
<br />B. ILLUMINATING ENGINEERS SOCIETY (IES)
<br />C. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
<br />D. NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)
<br />NOTE: THESE STANDARDS ARE SUBORDINATE TO STANDARDS SET BY U.L. AND LOCAL CODES.
<br />24. WIRING DEVICES SHALL BE SPECIFICATION GRADE. MINIMUM SIZE OF OUTLET BOXES SHALL BE 4" SQ. TRADE.
<br />OUTLET BOXES SHALL BE PRESSED STEEL IN DRY LOCATIONS, CAST ALLOY WITH THREADED HUBS IN WET
<br />OR DAMP LOCATIONS AND SPECIAL ENCLOSURE FOR OTHER CLASSIFIED AREAS.
<br />25. ALL ELECTRICAL CONDUCTORS MUST BE IN CONDUIT. ALL CONDUITS SHALL BE INTERMEDIATE (IMC)
<br />OR RIGID GALVANIZED STEEL (RGS) EXCEPT THAT: (A) POLY VINYL CHLORIDE (PVC) CONDUITS MAY BE
<br />USED IN CONCRETE SLABS AND UNDERGROUND PROVIDED THAT ELBOWS AND RISERS ARE RGS; (B)
<br />ELECTRICAL METALLIC TUBING (EMT) MAY BE USED IN WALLS OR CEILINGS OF FINISHED AREAS WHERE
<br />NOT SUBJECT TO MECHANICAL DAMAGE, OR CORROSIVE CONDITIONS; (C) LIQUID TIGHT FLEXIBLE CONDUIT
<br />WHERE REQUIRED IN WET OR DAMP LOCATIONS; (D) FLEXIBLE METALLIC CONDUIT WHERE REQUIRED
<br />IN DRY LOCATIONS. FLEXIBLE CONDUITS SHALL BE USED FOR ALL VIBRATING EQUIPMENT SUCH AS MOTORS,
<br />ETC.ALL CONDUITS IN HAZARDOUS LOCATIONS SHALL MEET THE REQUIREMENTSOF NEC CHAPTER 5.
<br />THE USE OF ENT CONDUIT IS PROHIBITED.
<br />26. APPLY 2 COATS OF BITUMASTIC COATING TO ALL METALLIC CONDUITS INSTALLED UNDERGROUND.
<br />27. NO CONDUITS TO BE RUN IN DUCT WORK. A POLYESTER PULL CORD SHALL BE INSTALLED IN ALL EMPTY
<br />CONDUITS.
<br />28. SIZE ALL WIREWAYS ACCORDING TO N.E.C. ARTICLE 376 AND 378
<br />29. ALL RATED WALL/FLOOR PENETRATIONS ARE TO BE SEALED WITH A FIRE RATED SEALER, PER ASTM E814.
<br />30. WHERE CORE DRILLING OF FLOORS/WALLS IS REQUIRED, CONTRACTOR SHALL SEAL OPENINGS AFTER
<br />UTILITIES HAVE BEEN INSTALLED. LOCATION OF CORED HOLES SHALL COORDINATE WITH LOCATION OF
<br />EQUIPMENT IN A MANNER TO BE CLEAN AND FUNCTIONAL. THE CONTRACTOR SHALL INSTALL ONLY ONE
<br />CONDUIT PER HOLE AND SEAL AROUND THE OPENING AS SPECIFIED ABOVE.
<br />31, ANY VARIATION FROM THE PLANS ARE TO BE PREVIOUSLY APPROVED BY THE ENGINEER IN WRITING.
<br />32. CONDUIT AND ELECTRICAL EQUIPMENT EXPOSED TO WEATHER MUST BE WEATHERPROOF (NEMA 3R).
<br />33. FUSES SHALL BE BUSSMAN "FUSETRON" DUAL -ELEMENT FUSES FOR BRANCH CIRCUIT PROTECTION AND
<br />ALSO FOR MOTOR RUNNING PROTECTION IF REQUIRED, OR FUSES AS CALLED FOR ON DRAWINGS.
<br />34. TERMINATIONS ARE TO BE MADE AS PER U.L. ARTICLE 486B.
<br />35. THE GENERAL CONTRACTOR SHALL COORDINATE ALL ELECTRICAL SITE WORK.
<br />36. ALL CIRCUIT BREAKERS SHALL BE INVERSE TIME TYPE (THERMAL MAGNETIC). MULTI -POLE CIRCUIT
<br />BREAKERS SHALL BE COMMON TRIP. NO TIE HANDLES PERMITTED.
<br />37. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR FOR THE ADVANCED ORDERING OF LONG LEAD
<br />ITEMS, AS NOT TO INTERFERE WITH THE PRODUCTION OF OTHER TRADES RESULTING IN ANY DOWN
<br />OR LAG TIME.
<br />38. THE CONTRACTOR SHALL VERIFY CIRCUIT DEVICE PROTECTIVE RATING FOR EQUIPMENT PRIOR TO
<br />CONSTRUCTION.
<br />39. USE 3/4" EXTERIOR GRADE PLYWOOD BACKBOARDS FOR SURFACE MOUNTING GROUPED EQUIPMENT,
<br />PAINTED ON BOTH SIDES AND EDGES WITH TWO COATS OF NAVAL GRAY PAINT (FIRE RESISTANT).
<br />40. NO CUTTING OR DRILLING OF STRUCTURAL ITEMS SHALL BE DONE WITHOUT PRIOR WRITTEN APPROVAL
<br />FROM A LICENSED STRUCURAL ENGINEER.
<br />41 ALL DEDICATED OUTLETS SERVING EQUIPMENT SUCH AS REFRIGERATORS, WATER COOLERS, COPIERS, FAXES,
<br />ETC. SHALL HAVE SEPARATE NEUTRAL CONDUCTORS TO EACH DEVICE OR APPLIANCE.
<br />42 ELECTRICAL POWER AND CONTROL WIRING FOR H.V.A.C. AND MECHANICAL EQUIPMENT SHALL BE FURNISHED
<br />AND INSTALLED BY THE ELECTRICAL CONTRACTOR.
<br />43 ELECTRICAL CONTRACTOR SHALL VERIFY THE CEILING FINISHES AND SUSPENSION SYSTEMS FOR SELECTION
<br />OF THE PROPER TRIM AND SUPPORT ARRANGEMENTS OF THE FIXTURE.
<br />44 ALL ELECTRICAL EQUIPMENT SHALL BE APPROVED AS SAFE FOR USE IN THE U.S. WORKPLACE, AS PER A
<br />"NRTL" RECOGNIZED ORGANIZATION (U.L., C.S.A., ETC.).
<br />45 PROVIDE EXPANSION JOINTS WHERE REQUIRED AS PER N.E.C. 300-7(b).
<br />I To the best of the Architect's'<nowledge these plans comply with the minimum standards of the applicable codes and life safety standards as determined in accordance with Chapter 553 and 663 of the Florida statutes
<br />For Construction
<br />Review Set
<br />Not for Construction
<br />®
<br />Permit Set
<br />Bid Set
<br />Record Set
<br />LIGHTING FIXTURE
<br />(SEE LIGHTING FIXTURE SCHEDULE ALSO)
<br />® Oa
<br />CEILING LIGHT FIXTURE -UPPER CASE LETTER DESIGNATES FIXTURE TYPE, LOWER CASE LETTER
<br />DESIGNATES SWITCHING.
<br />-,
<br />EXIT SIGN (LIGHT FIXTURE) CEILING OR WALL MOUNTED DOUBLE SIDED SIGN- CONNECTED TO LIGHTING CIRCUIT.
<br />ARROWS INDICATE DIRECTIONS. PROVIDE WITH BATTERY PACK.
<br />TYPES
<br />CEILING OR WALL MOUNTED EXIT SIGN FIXTURE. CONNECTED TO LIGHTING CIRCUIT.
<br />AS SPECIFIED IN FIXTURE SCHEDULE. PROVIDE WITH BATTERY PACK.
<br />pCEILING
<br />TYPES
<br />OR WALL MOUNTED EMERGENCY/EXIT SIGN COMBO FIXTURE. CONNECTED TO LIGHTING CIRCUIT.
<br />AS SPECIFIED IN FIXTURE SCHEDULE. PROVIDE WITH BATTERY PACK.
<br />DUAL HEAD EMERGENCY STAND-BY LIGHT, WITH BATTERY PACK, WALL MOUNTED.
<br />MT. UP 7-6" A.F.F. TO � OF OUTLET BOX.
<br />�--�
<br />EXISTING HID EXTERIOR LIGHTING FIXTURE - POLE MOUNTED
<br />RECESSED MOUNTED 2X4 LED FIXTURE.
<br />E
<br />RECESSED MOUNTED 2X2 LED FIXTURE.
<br />&;J
<br />RECESSED MOUNTED 2X4 LED FIXTURE. HATCH DENOTES BATTERY BACK UP
<br />RECESSED MOUNTED 2X2 LED FIXTURE. HATCH DENOTES BATTERY BACK UP
<br />CEILING MOUNTED OCCUPANCY SENSOR. MODEL VAC-DT SERIES OR EQUIVALENT.
<br />WIRE AS PER MANUFACTURER SPECS
<br />TOGGLE SWITCHES
<br />(SPECIFICATION GRADE - IVORY COLOR)
<br />$a
<br />SINGLE POLE TOGGLE SWITCH, 20 AMP, 120/277V.,SPECIFICATION GRADE. LETTER DENOTES LIGHTS ON
<br />SWITCH "A'. MOUNT AT 48' A.F.F. TO CL OF OUTLET BOX UNLESS NOTED.
<br />2
<br />110
<br />TWO POLE TOGGLE SWITCH , 20 AMP, 120/277V., SPECIFICATION GRADE LETTER DENOTES
<br />LIGHTS ON SWITCH "A'. MOUNT AT 48' A.F.F. TO CL OF OUTLET BOX UNLESS NOTED,
<br />3 THREE
<br />1'0
<br />WAY SWITCH , 20 AMP, 120/277V., SPECIFICATION GRADE LETTER DENOTES
<br />LIGHTS SWITCHED. MOUNT AT 48" A.F.F. TO CL OUTLET BOX UNLESS NOTED.
<br />4
<br />1'0
<br />FOUR WAY SWITCH , 20 AMP, 120/277V., SPECIFICATION GRADE LETTER DENOTES
<br />LIGHTS SWITCHED. MOUNT AT 48" TO CL OF OUTLET BOX A.F.F. UNLESS NOTED.
<br />6 =
<br />OCCUPANCY/VACANCY SENSOR SWITCH VNW-D OR EQUIVALENT.
<br />1,-
<br />LED COMPATIBLE DIMMER SWITCH. MT. AS DIRECTED ON PLAN.
<br />RECEPTACLES
<br />(SPECIFICATION GRADE - IVORY COLOR)
<br />po
<br />DUPLEX RECEPTACLE; 20 A.,120 V.,GROUNDING TYPE. MOUNTED 18" A.F.F. TO CL OF OUTLET BOX.
<br />(EXCEPT AS NOTED). HUBBELL 52621 U.O.N.
<br />GO
<br />DUPLEX RECEPTACLE; 20 A.,120 V.,GROUNDING TYPE. VERIFY MOUNTING HEIGHT. HUBBELL 52621 U.O.N.
<br />k�
<br />DUPLEX RECEPTACLE; 20 A.,120 V.,GROUNDING TYPE. SWITCHED AS PER PLAN.
<br />C30
<br />QUADUPLEX RECEPTACLE 20 A., 120 V., GROUNDING TYPE. MOUNTED 18" A.F.F.. HUBBELL 4151 U.O.N.
<br />D
<br />DEDICATED HOSPITAL GRADE DUPLEX RECEPTACLE; 20 A.,120 V.,GROUNDING TYPE. MAY BE
<br />INSTALLED IN COVER OF WIREMOLD.
<br />DUPLEX RECEPTACLE MOUNTED HORIZONTALLY; 20 A.,120 V.,GROUNDING TYPE. MOUNTED AS NOTED ON PLANS
<br />(EXCEPT AS NOTED).
<br />DUPLEX GFI RECEPTACLE MOUNTED HORIZONTALLY; 20 A.,120 V.,GROUNDING TYP�. MOUNTED UP AS NOTED ON
<br />PLANS. EXCEPT IN RESTROOMS NEXT TO SINKS WHERE IT SHALL BE MOUNTED AT 42' A.F.F. TO C OF OUTLET.
<br />DUPLEX RECEPTACLE; 20 A.,120 V.,GROUNDING TYPE. MOUNTED 18" A.F.F. TO C OF OUTLET BOX.
<br />(EXCEPT AS NOTED). CONNECTED THRU EMERGENCY PANEL.
<br />14
<br />CEILING MOUNTED OUTLET BOX FLUSH WITH TILE.
<br />F-0
<br />D
<br />DRYER RECEPTACLE. MT. UP 42" TO � OF OUTLET BOX.
<br />LJ
<br />LJ
<br />DENOTES FLOOR MOUNTED
<br />TELEPHONE SYSTEM
<br />DATA OUTLET 4-11/16" X 4-11/16" 2-1/8" WITH BUSHED HOLE COVER PLATE- MOUNTED
<br />18" A.F.F. TO � OF OUTLET(EXCEPT AS NOTED) PROVIDED 3/4" E.C. FROM EACH OUTLET TO STUB UP 6"
<br />ABOVE CL'G SPACE (EXCEPT AS NOTED.)
<br />>1
<br />DEDICATE PHONE LINE MOUNTED 18" A.F.F.LTO C OF OUTLET(EXCEPT AS NOTED) PROVIDED 3/4"
<br />E.C. FROM EACH OUTLET TO STUB UP 6" ABOVE CL'G SPACE (EXCEPT AS NOTED.)
<br />CONDUITS
<br />1�
<br />ARROW DESIGNATES "HOMERUN" TO PANEL,HASH MARKS DESIGNATE NUMBER OF WIRES.
<br />INDICATES GREEN BOND WIRE
<br />------
<br />INDICATES CONDUIT RUN EXPOSED.
<br />NSS
<br />TRANSIENT VOLTAGE SURGE SUPPRESOR
<br />POWER DISTRIBUTION
<br />Vii
<br />I�
<br />VARIBLE FREQ. DRIVE WITH LINE SIDE BRAKER FURNISHED BY DIV. 15 MT'D AND CONNECTED BY DIV. 16
<br />EP
<br />SAFETY SWITCH - HEAVY DUTY NEMA CLASS "A" IN NEMA 1 ENCLOSURE, OUTDOOR TYPE NEMA 3R.
<br />20
<br />3 Q
<br />DESIGNATES SWITCH RATING, "3" DESIGNATES POLES; "20" TIME DELAY FUSE; "30"SWITCH AMPS.
<br />HVAC MOTORIZED DAMPER FURNISHED BY DIV. 15
<br />CONNECTED BY DIV. 16 CONTRACTOR.
<br />4
<br />MOTOR. (FURNISHED BY ARCH. DIV. 13, OR 15 CONNECTED BY DIV 16. OR ELEV./ESC. INSTALLER)
<br />®
<br />120/208V., 30, 4W. PANEL BOARD.
<br />REMOTE EMERGENCY OFF SHUNT TRIP SWITCH.
<br />JUNCTION BOXES
<br />EQUIPMENT JUNCTION BOX, FURNISHED WITH EQUIPMENT.
<br />a/O
<br />WALL CEILING MOUNTED JUNCTION BOX.
<br />MINIMUM 4" X 4" X 1 1/2" WITH BLANK PLATE. MT. WALL BOX UP AS SHOWN ON PLAN.
<br />dVos
<br />WALL/CEILING MOUNTED J.BOX FOR SIGNAGE. MT. WALL BOX UP AS SHOWN ON RAN.
<br />AUXILIARY SYSTEMS
<br />INTERCOM CALL BUTTON AND VOLUME CONTROL SWITCH
<br />C S
<br />COMBINATION CLOCK SPEAKER
<br />ED
<br />SINGLE GANG JUNCTION BOX FOR P.A. HORN SPEAKER. CONTRACTOR TO FIELD COORDINATE MOUNTING HEIGHT.
<br />ABBREVIATIONS
<br />ABBREVIATION
<br />DESCRIPTION
<br />ABBREVIATION
<br />DESCRIPTION
<br />A.C.T.
<br />ABOVE COUNTER TOP
<br />K.V.A.
<br />KILOVOLT AMPERES
<br />A.F.F.
<br />ABOVE FINISHED FLOOR
<br />MAX.
<br />MAXIMUM
<br />(TYP.)
<br />TYPICAL
<br />MIN.
<br />MINIMUM
<br />PNL.
<br />PANEL
<br />(MFR) MANUF.
<br />MANUFACTURER
<br />L.T.
<br />LIGHT
<br />GFI.
<br />GROUND FAULT INTERRUPTER
<br />FIXT.
<br />FIXTURE
<br />GND.
<br />GROUND
<br />BRKR.
<br />BREAKER
<br />W.P.
<br />WEATHER PROOF
<br />0
<br />PHASE
<br />M.C.B.
<br />MAIN CIRCUIT BREAKER
<br />PVC
<br />POLYVINYL -CHLORIDE
<br />F/N
<br />FULL NEUTRAL
<br />RGS
<br />RIGID GALVANIZED STEEL
<br />SURF.
<br />SURFACE
<br />PWR.
<br />POWER
<br />HTD.
<br />MOUNTED
<br />MTG.
<br />MOUNTING
<br />REC.
<br />RECEPTACLE
<br />oss if 1, 2 or 3 Hour Fire Rated
<br />�a Through Penetration Firestop for
<br />Single Metal Pipe through
<br />Concrete floors or walls using
<br />SYsIt TREMstop WBM.
<br />CAJ1144 F-RATING = 1, 2 and 3 Hr.
<br />T-RATING = 1, 2 AND 3 Hr. F=T
<br />2
<br />3A 36
<br />1
<br />.d.
<br />2 a.
<br />a
<br />3B
<br />3A
<br />DRAWING NOT TO SCALE
<br />10 FLOOR OR WALL ASSEMBLY = 4" TO 6" THICK CONCRETE.
<br />Q STEEL PIPE: 6" DIAMETER (OR SMALLER) SCHEDULE 40 (OR
<br />HEAVIER)
<br />STEEL.
<br />Q Max. Pipe Min. Forming Min. Fill F
<br />T
<br />Diameter Mat[. Thkns Mat]. Thkns Rating
<br />Rating
<br />(inches) (inches) (inches) (Hour)
<br />(Hour)
<br />6 4 0.5 1
<br />0
<br />4 3.5 1 2
<br />0.5
<br />6 1.25 2.375 3
<br />0
<br />* ANNULAR SPACE IS 3/4"
<br />A. 4.0 pcf MINIMUM DENSITY MINERAL WOOL INSULATION, FRICTION
<br />FITTED.
<br />B. MINIMUM FILL THICKNESS OF TREMstop WBM.
<br />NOTE:
<br />FOR WALLS APPLY TREMstop WBM TO BOTH SURFACES OF
<br />WALL.
<br />DETA L-A
<br />CONCRETE WALL OR SLAB PENETRAT ON DUAL-
<br />1 or 2 Hour Fire Rated Through
<br />oss if/. Penetration Firestop for Single
<br />G
<br />`Do Metal Pipe through Gypsum
<br />walls using TREMstop WBM.
<br />SYS t �
<br />VA/L1051 F-RATING = 1 and 2 Hr.
<br />T-RATING = 1 and 2 Hr.
<br />F=T
<br />31. 3 -
<br />Ito
<br />2 =_
<br />2
<br />[DRAWING NOT TO SCALE
<br />0 1 OR 2 HOUR FIRE RATED GYPSUM WALLBOARD/STUD WALL ASSEMBLY.
<br />0 STEEL PIPE: 6" DIAMETER (OR SMALLER) SCHEDULE 40 (OR HEAVIER) STEEL.
<br />CONDUIT:4" DIAMETER (OR SMALLER) EMT OR RIGID STEEL CONDUIT.
<br />CIRCULAR DUCT: 4" DIAMETER (OR SMALLER) 26 GAUAGE (OR HEAVIER)
<br />GALVANIZED STEEL VENT DUCT.
<br />0 TREMstop WBM: FILL MAXIMUM 3/4" ANNULUS WITH A THICKNESS OF 1
<br />1/4" (2 HOUR F-RATING) OR 3/4" (1 HOUR F-RATING).
<br />DETAIL-B.
<br />GYPSUM WALL PENETRATION DETA L
<br />All designs, details and drawings indicated and
<br />represented are for use on and in conjunction with
<br />the specified project, the designs and drawings
<br />are the property of the Architect and shall not be
<br />reproduced in whole or in part without the written
<br />permission of M3o Architecture, Inc
<br />
|