|
00
<br />LO
<br />Lr)
<br />LO
<br /><D
<br />01
<br />PI)
<br />5_4
<br />LO
<br />00
<br />CD
<br />W)
<br />LO
<br />LO
<br />9
<br />.2
<br />15
<br />-9
<br />0)
<br />15
<br />C�,
<br />00
<br />9
<br />a
<br />THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />3/8" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOWBUCKTO
<br />OUTSIDE EDGE OF
<br />MASONRY
<br />VANDOWBUCK
<br />/-2) SEALANT JOINT
<br />5) SEALANT FROM
<br />INSIDE EDGE OF
<br />WINDOW FRAME
<br />WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />K
<br />AND EXTEND TO
<br />-\AflNDOWFRAME
<br />MASONRY ---------------- - --------
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />W
<br />FRAME
<br />3) SEALANT WINDOW FRAME T(
<br />WINDOW BUCK ALL THE WAY
<br />AROUND, INCLUDING SILL.
<br />SCS 06 05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />"V'SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />HEAD FLASHING TIE-IN INSTRUXTI(
<br />1 . Cut, fold up & temporarily secure)
<br />resistive barrier above header to allow tor
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />FOLD UP WEATHER
<br />RESISTIVE BARRIER &
<br />TEMPORARILY SECURE
<br />WOOD FRAME CONSTR.
<br />EXTERIOR
<br />SELF -ADHERED FLASHIN
<br />SHEATHING
<br />BY LAPPING DOWN
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN,
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />EXTERIOR SHEATHING
<br />REFER TO TECHNICAL
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />SELF -ADHERED FLASHING
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING
<br />FLANGE
<br />NAILING FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SCS 0602 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />SINGLE
<br />JOIST
<br />SELF -ADHERED
<br />FLASHING
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />SEAL TOPS OF JOIc
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />ED FLASHING
<br />SELF -ADHERED FLASHING
<br />7-DOUBLE
<br />JOIST
<br />WOODBEAM
<br />BELOW
<br />SELF -ADHERED
<br />FLASHING
<br />2x FRAMEWALL
<br />TILE FINISH -
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />1/2" DUROCK
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />Detail Instructions
<br />V-4" PER PLAN
<br />Refer to the number marked as # in each detail that corresponds to the
<br />G
<br />V-0" PER PLAN
<br />numbered items in the list of instructions below:
<br />1 Install self -adhered flashing in order as shown by numbers
<br />8" CMU
<br />C-MIDE
<br />2� Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />4" OR 8" CMU
<br />3. Self -adhered flashing can be substituted for building paper
<br />(PER SEAT DEPTH) -------- --
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />FILL WITH GROUT
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />SLOPED MUD BED
<br />4
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />4
<br />VINYL SHOWER PAN
<br />8. Mechanically fasten as necessary
<br />H
<br />SL PE
<br /><
<br />SHOWER SEAT
<br />WEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />3/4"-V BEAD OF CONSTR,
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL WP02)
<br />SELF -ADHERED FLASHING
<br />SEAL TOPS OF JOISTS
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />SELF-ADHER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />DOOR ROUGH OPENING
<br />WINDOW UNIT
<br />SLOPE
<br />FLASHING REQUIREMENTS
<br />0.3 in: 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />(0. 6 cm : 30.5 cm) include flashing as described in Section R703.4.
<br />314"-V BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING
<br />THRESHOLD OF DOOR AND I
<br />RETURN UP JAMS 6". USE LIQUID R703.1.1 Water resistance. The exteriorwall envelope shall be designed and constructed in a mannerthat prevents the accumulation of
<br />NAIL BRAND OR EQUAL WEATHER EXTERIOR water within the wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means
<br />PROOF CAULKING CEMT. FIN,
<br />of draining to the exterior water that penetrates the exterior cladding.
<br />SELF -ADHERED FLASHING BUILDING PAPER
<br />WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />SUBFLOOR other approved water -resistive barrier shall be applied over studs or sheathi
<br />g
<br />f
<br />ll
<br />t
<br />i
<br />r
<br />ll
<br />N
<br />. 15
<br />ph
<br />lt f
<br />lt
<br />h
<br />ll b
<br />pplied
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The
<br />RIM JOIST No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />Plan;
<br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied fa
<br />two layers of Grade
<br />wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to 1116M) 6
<br />ly
<br />D paper. The individual layers shall be- installed independently such that each layer provides a separate continuous plane and any flashing
<br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDERLIZO Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance
<br />jilt equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT substantially nonwater-absorbing layer or designed drainage space.
<br />RUBBERIZED
<br />INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE
<br />FLASHING JAMB & HEAD THROUGH SELF -ADHERED R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be
<br />FLASHING, SEE FLASHING SELF -ADHERED FLASHING
<br />FLANGED \MNDOW applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied
<br />(SEE DETAIL VVP01) membranes used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to
<br />SCORED prevent the entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />RELEASE PAPER
<br />Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />(BEFORE FOLDING, SCORE
<br />SELF -ADHERED FLASHING, the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />RELEASE PAPER TO EXPOSE
<br />EXTEND A MINIMUM 6" ADHESIVE AS SHOWN) contraction, ASTMC1 281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />VERTICALLY FROM
<br />BOTTOM OF flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />THRESHOLD
<br />shall be installed at the following locations:
<br />1. 1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />2 following:
<br />pr-
<br />5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or detailsl
<br />4
<br />are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />6 sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for
<br />subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />7
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />1.3 1.3. In accordance with other approved methods.
<br />SELF -ADHERED FLASHING
<br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />INSIDE CORNER
<br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />Ground
<br />4.4.Continuously above all projecting wood trim.
<br />7
<br />-frame construction.
<br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood
<br />6.6.At wall and roof intersections.
<br />4PER
<br />-in q
<br />Water Resistant Barrier 7. 7.At built utters.
<br />Z Z
<br />LU PLASTER STOP
<br />U)
<br />U) CONTINUOUS BACKER
<br />LU
<br />0 ROD & SEALANT
<br />M o
<br />LU
<br />Ir
<br />Ir
<br />LU
<br />LU
<br />W 3:
<br />0
<br />U)
<br />:LF-ADHERED FLASHING
<br />7CH
<br />HERED FLASHING
<br />2
<br />4
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />-----BOND BREAK WRB
<br />SF LATH
<br />-WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />tFLANGE AS AN AIR
<br />BARRIER
<br />3-112" INCH FLANGE
<br />THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE.
<br />DO NOT SEAL.
<br />DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTI LEVER
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) _C1 ------ 0-
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB)
<br />BOND BREAKWEATHER RESISTANT BARRIER -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING, 'OSB', PLYWOOD, DENSGLASS
<br />STRUCTURAL FRAMING
<br />STRUCTURAL SHEATHING
<br />----STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />- - - - - -
<br />- - - -
<br />STOP
<br />A
<br />R D
<br />4T
<br />TIOUS FINISH
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />-1
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />711" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC 1063
<br />Building Paper
<br />7/16" 0. S. B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs,
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2" to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC 1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />AM
<br />av
<br />�ual Revietv
<br />ev. Assi-st
<br />ow
<br />IL
<br />, Inc.
<br />Rce I
<br />wl-complet,-,
<br />I, th th I'd aPproii,
<br />ebra e 2020 Id
<br />Ann, FRC 7 -
<br />111ahr 11
<br />pX2 lditio,7
<br />300
<br />24-
<br />00
<br />2
<br />CY'>
<br />0D , 0
<br />P!:
<br />Z� .: No
<br />E:
<br />t
<br />To the best of the Engineers knowledge. information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2020 Florida Building Code
<br />-
<br />Residential 7th Edition. Engineers signature and seal
<br />is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineers signature and seal.
<br />WA
<br />lot E S
<br />8 4 c4o
<br />0)
<br />0 ui�
<br />(0
<br />LO ,
<br />0 :01 [ F UJ
<br />N 0
<br />U u_ Z
<br />0
<br />" 5
<br />Z 3: �0
<br />Iwo 3: 0
<br />45 �a (� - -
<br />W 0 2 r- M
<br />111 in �) Z
<br />Z - -� 0 !;Li
<br />U�l co 0
<br />.. < L) U) i-
<br />Z 00 El El Li
<br />W
<br />g
<br />V)
<br />Q) (D
<br />ro
<br />0
<br />U) C_
<br />\,�/ L/)
<br />i__ U)
<br />U
<br />= CD
<br />M 0
<br />I k < 0
<br />_!
<br />40,
<br />It
<br />C.0
<br />C1_>
<br />cl>
<br />-z
<br />,
<br />Z
<br />Z
<br /><
<br />__J
<br />ILI-
<br />E
<br /><
<br />19
<br />Z,
<br />co
<br />E
<br />n 0
<br />00
<br />0<
<br />Z
<br />U�- fa
<br />w
<br />0,
<br />0,
<br />Z,
<br />Z
<br />.2
<br />>-
<br />co
<br />0
<br />10
<br />-
<br />W
<br />Z
<br />w
<br />A
<br />�t
<br />0
<br />�,
<br />Not
<br />63:1
<br />L
<br />E2
<br />9(D
<br />L0
<br />L0
<br /><
<br />C:)
<br />�!e
<br />LO
<br />4-1
<br />4_J W
<br />V) C,0
<br />0
<br />1
<br />CN
<br />C)
<br />U-)
<br />00
<br />-0
<br />CN
<br />C:)
<br />-0 LO 00
<br />00
<br />LO
<br />co
<br />< co
<br />E
<br />(0
<br />CY)
<br />0
<br />ca
<br />Z
<br />E
<br />ca
<br />O_
<br />E
<br />0 0 '0
<br />0 <
<br />0
<br />JOB
<br />NO 23-02469
<br />SCALE AS NOTED
<br />SHEET NO.
<br />W P
<br />
|