|
FOLD UP WEATHER
<br />RESISTIVE BARRIER & WEATHER RESISTIVE WINDOW UNIT FLASHING REQUIREMENTS
<br />TEMPORARILY SECURE BARRIER
<br />DOOR ROUGH OPENING SLOPE
<br />WEATHER
<br />RESISITIVE 0.3 in : 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />BARRIER WOOD FRAME CONSTR. (0.6 cm: 30.5 cm) include flashing as described in Section R703.4.
<br />EXTERIOR
<br />iL
<br />' SELF -ADHERED FLASHING 3/4"-1' BEAD OF CONSTR.s SHEATHING BY LAPPING DOWNADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING
<br />OVER RIM JOIST AND UP THRESHOLD OF DOOR ANDWALL BY 6 IN. RETURN UP JAMB 6". USE LIQUID R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of
<br />D WINDOW) O NAIL BRAND OR EQUAL WEATHER EXTERIOR water within the wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means
<br />z PROOF CAULKING CEMT. FIN.
<br />O BUILDING PAPER of draining to the exterior water that penetrates the exterior cladding.
<br />WEATHER SELF -ADHERED FLASHING
<br />RESISITIVE
<br />2 BARRIER SEAL TOPS OF JOISTS 1 WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />UNDER DECKING
<br />SUBFLOOR other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied
<br />(SEE DETAIL WP07)
<br />SELF -ADHERED FLASHING horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The
<br />HEAD FLASHING TIE-IN INSTRUXTIONS: RIM JOIST No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and
<br />1. Cut, fold up & temporarily secure weather building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />THESE DETAILS ARE GENERIC AND resistive barrier above header to allow for
<br />flashing installation
<br />MEANT TO SHOW GENERAL FLASHING 2. Self -adhered flashing plus head flashing under R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over
<br />AND WATERPROOFING METHODS TO weather resistive barrier wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade
<br />BE USED. 3. Fold weather resistive barrier back over head V G D paper. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing
<br />flashing and seal with tape
<br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING Scale: IN SELF -ADHERED FLASHING SELF -ADHERED FLASHING
<br />FLANGED WINDOW m
<br />EXTERIOR DOOR WITH DECK - SECTION A 1 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER 1 Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />substantially nonwater-absorbing layer or designed drainage space.
<br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT
<br />EXTERIOR SHEATHING RUBBERIZED
<br />NEEDED IN CORNERS ADHESIVE
<br />3(4"-1" BEAD OF CONSTR. INSTALL SELF -ADHERED ASPHALT ADHESIVE
<br />EXTERIOR SHEATHING ADHESIVE TO BE APPLIED UNDER FLASHING JAMB & HEAD THROUGH SELF -ADHERED R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be
<br />3/8" CEMENT THRESHOLD OF DOOR AND RETURN FLASHING. SEE FLASHING SELF -ADHERED FLASHING applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied
<br />PLASTER UP JAMB 6". USE LIQUID NAIL BRAND FLANGED WINDOW
<br />12 MIL DRYLOK CMU -MASONRY BLOCK OR EQUAL WEATHER PROOF CAULKING (SEE DETAIL WP01) membranes used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to
<br />REFER TO TECHNICAL SCORED prevent the entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />EXTREME LETTER ON CHEMICAL o RELEASE PAPER Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />WINDOW COMPATIBILITY
<br />(BEFORE FOLDING, SCORE the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />FASTENER SELF -ADHERED FLASHING e SELF -ADHERED FLASHING, ° RELEASE PAPER TO EXPOSE
<br />1)SEALANT AT ° EXTEND A MINIMUM 6-4 ADHESIVE AS SHOWN) contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />4) SEALANT JOINT WINDOW BUCK TO VERTICALLY FROM
<br />OUTSIDE EDGE OF MASONRY BOTTOM OF flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />WINDOW BUCK THRESHOLD
<br />2) SEALANT JOINT ^ shall be installed at the following locations:
<br />5) SEALANT FROM INSIDE EDGE OFWINDOW FRAME
<br />ACROSS WINDOW BUCK WINDOW BUCK SECTION -A (SEE DETAIL WP02) g g openings 1.1.Exterior window and door openings. Flashing at exterior window and door o enin s shall extend to the surface of the exterior wall
<br />AND EXTEND TO WINDOW FRAME finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />MASONRY ATTACHED SELF -ADHERED FLASHING
<br />PER CODE O shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />6) TOOLED SEALANT REQUIREMENTS 2 following:
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW 2 5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />FRAME SELF -ADHERED FLASHING
<br />3) SEALANT WINDOW FRAME T NAILING FLANGE 4 manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details
<br />WINDOW BUCK ALL THE WAY 1 O are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />AROUND, INCLUDING SILL. 2 SEAL TOPS OF JOISTS 6 sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for
<br />BDO NOT OTTOM NAILING NG OVER
<br />$ UNDER DECKING 2 7 subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />FLANGE (SEE DETAIL WP07)
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />1.3 1.3. In accordance with other approved methods.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND SELF -ADHERED FLASHING SELF FLASHING SELF -ADHERED FLASHING , 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />FENESTRATION INSTALLATION AND INTERFACE HALF ROUND WINDOW ' EXTERIOR
<br />OR DOOR WITH DECK ' INSIDE CORNER
<br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />Ground 3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />4.4.Continuously above all projecting wood trim.
<br />SHEATHING 5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />1 6.6.At wall and roof intersections.
<br />Water Resistant Barrier 7.7.At built-in gutters.
<br />Lath
<br />JAMB, SILL AND HEAD DETAIL SELF -ADHERED FLASHING
<br />APPROVED SHEATHING Sheathing THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />APPROVED HOUSEWRAP PATCH
<br />Stucco FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME ° °
<br />� 2
<br />APPROVED FLASHING TAPE DOUBLE O -'
<br />" Cement
<br />W" SEALANT SOCKET WITH JOIST Ill/ accordance with Plaster 7/8" Cement Plaster
<br />TOOLED APPROVED SEALANT SINGLE WOOD BEAM Foundation Wall °
<br />JOIST BELOW 1 SELF -ADHERED FLASHING ASTMC926 in accordance with
<br />SELF -ADHERED FLASHING ASTMC926
<br />Felt backed metal
<br />2 ° ° lathe in accordance Felt backed metal
<br />3" MIN with ASTMC1063 lathe in accordance
<br />SELF -ADHERED SELF -ADHERED 4
<br />with ASTMC1063
<br />FLASHING FLASHING Q 5 Building Paper
<br />' � � , Building Paper
<br />7/16" O.S.B.
<br />7/16"
<br />FLASHING • sheathing sheathing
<br />ing
<br />SCS 06_02 WINDOW FIN INTERFACE WITH SELF-ADHEREDDECK JOIST �' SELF -ADHERED FLASHING ' FOUNDATION WEEP SCREED
<br />EXTRUDED SHOULDER OUTSIDE CORNER • Metal g y sheathing
<br />Flashing
<br />Weep Screed
<br />T -,I Installed As Per
<br />SELF -ADHERED FLASHING 2x FRAMEWALL - - - - - p Manufact. Specs.
<br />¢ 1I STRIP OF SAF LEGEND Maintain Stampede or similar
<br />PRODUCTS DETAILS TILE FINISH I SELF DRAINAGE
<br />FLASHING (SAF) Bottom Of CBUk bottom
<br />DRAINAGE PLANE WRB DRAINAGE PLANE (DP) WEATHER RESISTANT Weep Screed joint only
<br />LU J % BARRIER (WRB) - - 1 1/2" to 2"
<br />U) I I BOND BREAK WRB BOND BREAK WEATHER RESISTANT BARRIER- Weep Screed
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO 1/2" DUROCK > 11 SELF FURRING (SF) LATH Above Roof
<br />m I I PLASTER ACCESSORY Sheathing Installed As Per
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020) ¢ , I SF LATH SHEATHING,'OSB', PLYWOOD, DENSGLASS Manufact. Specs.
<br />1'-4" PER PLAN I {
<br />Detail Instructions i WRAP DP WRB ONTO
<br />I 1/2' Cementitious
<br />1'-0" PER PLAN 'v I (I THE VERTICAL Cement Plaster
<br />Refer to the number marked asO# in each detail that corresponds to the \ I SURFACE TO TOP of Decorative Finish
<br />numbered items In the list Of instructions below: I FLANGE AS AN AIR In accordance
<br />' 11 BARRIER with ASTMC926 q �,o°® inside and
<br />SLOPE I 1 I over wood 2nd ,0°0 ' ' ° ° oultside corner will
<br />1. Install self -adhered flashing in order as shown by numbers 8" CMU _ _ - 41 1 I I 3-1/2" INCH FLANGE
<br />2. Install flashing and weather resistive barrier to form water shedding I I I ,.�
<br />floor 0•°,° need to be miter
<br />4" OR 8" CMU Q - - - - - - -- - - - - - - - - J 11 cut and caulked all
<br />laps (PER SEAT DEPTH) Ii F a , I '°®•o,•o• butt joints need to
<br />3. Self -adhered flashingcan be substituted for building paper z Z I STRUCTURAL FRAMING c,° o,o••
<br />9p p r
<br />4. Split the release paper using the ripcord (Split release on demand, FILL WITH GROUT 1 1 - g \V " �,� ? STRUCTURAL SHEATHING ' °°c, m •4 ' becaulked using
<br />' Stampede or sim.
<br />embedded in the adhesive layer) - for ease of installation and to THIS GAP IS RESULT OF `.i caulk for all
<br />minimize scoring cuts a W W PLASTER STOP STRIP OF SAF
<br />g CUa a- NATURAL SHRINKAGE.
<br />5. Remove all release paper per standard installation instructions and _ = U) CONTINUOUS BACKER _ ---- ----
<br />° _ i DO NOT SEAL. I� I, � DRAINAGE PLANE WRB
<br />Lu
<br />adhere to substrate using a square piece of flashing material (6" x 6" DRIP SCREED PLASTIC I
<br />G- _I w W ROD &SEALANT ACCESSORY - 1�BOND BREAK WRB
<br />Minimum) SLOPED MUD BED y = M ' \ '
<br />6. Fold as shown by arrows'- Lu
<br />o ° Q € i SF LATH
<br />LIJ I /
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to ICI U) o
<br />VINYL SHOWER PAN NI ° = A ;; Note:
<br />fit tight to corner
<br />t1
<br />------ -- --- - --- - ---- The building paper and metal lath must be
<br />8. Mechanically fasten as necessary
<br />SLOPE d - ' '
<br />° �_ ) Cement installed over the top of the weep screed.
<br />° PLASTER STOP J� Plaster
<br />CONTINUOUS BACKER ROD over block
<br />& SEALANT 1 st floor
<br />CEMENTITIOUS FINISH
<br />SHOWER SEAT ■ SOFFIT/CANTILEVER • � WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />N
<br />N �
<br />cc
<br />0
<br />�
<br />� W
<br />o L
<br />0
<br />U O cz,
<br />c ti v C�
<br />�Ll Cc o _
<br />y, D N L
<br />Cc
<br />Q N Y
<br />CID o a
<br />U
<br />a
<br />s
<br />o
<br />a o
<br />CV
<br />N
<br />0
<br />N
<br />0
<br />To the best of the Engineers knowledge, information and belief,
<br />the structural plans and specifications contained within
<br />these
<br />drawings comply with the 2020 Florida Building Code -
<br />Residential 7th Edition. Engineer's
<br />signature and seal is
<br />only for
<br />the structural engineering portions
<br />of the drawing pages
<br />bearing
<br />Engineers signature and seal.
<br />� N
<br />W
<br />v E
<br />M O
<br />U
<br />IN°c) o
<br />0
<br />C
<br />(0N
<br />o n
<br />a0 rA N
<br />in #
<br />+
<br />N O 2S2S # LL
<br />LL 55 a
<br />13
<br />a Y
<br />(0 O
<br />- C-t�
<br />1%Z
<br />r m Z
<br />C� o
<br />W
<br />ox
<br />co
<br />Z1°o
<br />LL
<br />J
<br />m1 w
<br />Mn Z Q
<br />N
<br />o
<br />Z
<br />W
<br />OU
<br />U U)
<br />❑ ❑
<br />z N M
<br />O
<br />z 0
<br />63
<br />Z
<br />Q v
<br />E3
<br />N
<br />-- M
<br />z
<br />()
<br />U 6
<br />LL
<br />4
<br />w �
<br />O
<br />w o
<br />t�l
<br />�N(10
<br />_)
<br />U
<br />LU
<br />U 'o
<br />c rn
<br />Q CID 0
<br />em
<br />o
<br />c
<br />w
<br />Z
<br />co�
<br />M
<br />¢
<br />zo
<br />U_
<br />E
<br />o
<br />oo
<br />Q�
<br />14
<br />Q
<br />E O
<br />co
<br />wj
<br />��
<br />Z®
<br />oa
<br />as
<br />.0
<br />Q
<br />Z
<br />o E
<br />N 0
<br />nz
<br />`o
<br />az
<br />m
<br />i
<br />J
<br />m E
<br />:3 "'N
<br />Cr
<br />-
<br />U
<br />a zZ
<br />Z
<br />m
<br />Q W
<br />�z
<br />0)J
<br />Cn
<br /><°
<br />z
<br />QU
<br />Q
<br />8<
<br />az
<br />w
<br />W
<br />U
<br />wLL
<br /><paLL
<br />w
<br />s
<br />x3
<br />O
<br />F
<br />U
<br />a O
<br />O
<br />d F
<br />VO
<br />ila
<br />3
<br />o T
<br />m
<br />0
<br />E
<br />C0
<br />o
<br />r
<br />CN
<br />�+ Y
<br />r
<br />0
<br />m
<br />O
<br />QO
<br />E
<br />O
<br />t--
<br />�
<br />te
<br />CN
<br />a-+ CD
<br />N
<br />an
<br />CD
<br />to
<br />LO
<br />< CDT
<br />L 0
<br />00
<br />00
<br />00
<br />r
<br />a;
<br />M
<br />o
<br />Z
<br />Z
<br />E
<br />i,6
<br />c
<br />E
<br />�
<br />a.
<br />U °
<br />Q
<br />JOB
<br />NO : 22-09500-09493
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />
|