|
1 fl_ I I 1 111111 l I
<br />STRIPING CONDITIONS TACTILE EXIT SIGN
<br />4,-0„ TACTILE SIGN REQUIREMENTS
<br />1. A TACTILE SIGN STATING "EXIT" AND COMPLYING WITH ANSI Al17.1 SHALL BE PROVIDED ADJACENT SITE VERIFICATION REQUIREMENTS:
<br />TO EACH DOOR TO AN EXIT PASSAGEWAY AND THE EXIT DISCHARGE. REF FLOOR PLANS FOR
<br />WALL LOCATION LOCATIONS.
<br />MAY VARY 1. THE ARCHITECT HAS MADE A SCOPE VISIT WITH MEASUREMENTS AND PHOTOGRAPHS OF EXISTING CONDITIONS AND THE ARCHITECTURAL DRAWINGS
<br />Q Ci 2. FOR CHARACTER WIDTH, THE UPPERCASE LETTER "0" SHALL BE USED TO DETERMINE THE INDICATE EXISTING CONDITIONS VERIFIED IN THE FIELD. IT, HOWEVER, REMAINS THE RESPONSIBILITY OF THE CONTRACTOR TO VERIFY ALL EXISTING
<br />w ALLOWABLE WIDTH OF ALL CHARACTERS OF A FONT. THE WIDTH OF THE UPPERCASE LETTER "O„ CONDITIONS PRIOR TO THE SUBMISSION OF A BID AND TO THE COMMENCEMENT OF ANY WORK. NO ADDITIONAL COMPENSATION WILL BE PAID DUE TO THE
<br />ELECTRICAL iv OF THE FONT SHALL BE 55 PERCENT MINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE CONTRACTOR'S FAILURE TO VERIFY EXISTING SITE CONDITIONS WHICH INCLUDE, BUT ARE NOT LIMITED TO, GRADES, EXTENT OF PAVING, OR UTILITIES.
<br />- w UPPERCASE "I" OF THE FONT. (ANSI A117.1-2009: 703.3.6) CHARACTER HEIGHT MEASURED FROM 2. ANY DISCREPANCY WITH THE EXISTING SITE CONDITIONS AND/OR THE DRAWINGS SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT FOR
<br />THE BASELINE OF THE CHARACTER SHALL BE 5/8" (16 MM) MINIMUM AND 2 INCHES (51 MM) CLARIFICATION AND INSTRUCTION. THESE CONSTRUCTION DOCUMENTS HAVE BEEN DESIGNED AND DRAWN ASSUMING EXISTING BUILDING CONDITIONS
<br />'03 o Z MAXIMUM BASED ON THE HEIGHT OF THE UPPERCASE LETTER "I". MATCH THE ORIGINAL DRAWINGS. THE GENERAL CONTRACTOR, IMMEDIATELY UPON ARRIVAL AT THE SITE, SHALL VERIFY ALL EXISTING STRUCTURAL
<br />STRIPING AT EYEWASH COLUMN DIMENSIONS, STRUCTURAL BEARING HEIGHTS, EXISTING DIMENSIONS, TOP OF MASONRY ELEVATIONS, ROOFING CONDITIONS (INCLUDING
<br />Q O 3. CHARACTERS AND SYMBOLS SHALL CONTRAST WITH THEIR BACKGROUND. PARAPETS, SCUPPERS AND ROOF DRAINS), AND JOIST BEARING ELEVATIONS PRIOR TO THE FABRICATION OF ANY STRUCTURAL ITEMS. IF DISCREPANCIES
<br />ARE FOUND BETWEEN WHAT IS SHOWN ON THE DRAWINGS AND EXISTING FIELD CONDITIONS, CONTACT THE WALMART CONSTRUCTION MANAGER AND THE
<br />4. CHARACTERS SHALL CONFORM TO THE FOLLOWING: ARCHITECT IMMEDIATELY TO DETERMINE WHAT ACTION SHOULD BE TAKEN TO MATCH EXISTING CONDITIONS. THE BEGINNING OF STRUCTURAL STEEL
<br />Q 4.a. LETTERS AND NUMBERS ON SIGNS SHALL BE RAISED 1/32" MINIMUM AND SHALL BE SANS- FABRICATION BY THE GENERAL CONTRACTOR, STEEL FABRICATOR, OR JOIST MANUFACTURER MEANS ACCEPTANCE OF THE EXISTING CONDITIONS.
<br />00 r SERIF UPPERCASE CHARACTERS ACCOMPANIED BY GRADE 2 BRAILLE. 3. ALL UTILITY LOCATIONS SHOWN ARE APPROXIMATE. THE CONTRACTOR SHALL FIELD VERIFY THE EXACT LOCATION OF ALL EXISTING UTILITIES (WHETHER
<br />P7 L 4.b. RAISED CHARACTERS OR SYMBOLS SHALL BE A MINIMUM OF 5/8" HIGH AND A MAXIMUM OF 2". SHOWN OR NOT) PRIOR TO THE SUBMISSION OF A BID OR THE COMMENCEMENT OF CONSTRUCTION. THE CONTRACTOR SHALL NOTIFY THE WALMART
<br />CONSTRUCTION MANAGER OF THE DISCOVERY OF EXISTING UTILITIES NOT SHOWN OR NOTED ON DRAWINGS.
<br />z WALL LOCATION T-0„ 5. CONTRACTED GRADE 2 BRAILLE SHALL BE USED. DOTS SHALL BE 0.090" (2.3 MM) TO 0.100" (2.5 MM) 4. NOT USED.
<br />12'-10" ° MAY VARY ON CENTER IN EACH CELL WITH 0.241" (6.1 MM) TO 0.300" (7.6 MM) SPACE BETWEEN CELLS. DOTS 5. NOT USED.
<br />w SHALL BE RAISED A MINIMUM OF 0.025" (0.6 MM) TO 0.037" (0.9 MM) ABOVE THE BACKGROUND. 6. THE CONTRACTOR SHALL VERIFY EXACT LOCATIONS AND DEPTHS OF UNDERGROUND UTILITY SERVICES PRIOR TO ANY EXCAVATION.
<br />7. THE CONTRACTOR SHALL VERIFY ALL GRADES AND PROPOSED FINAL GRADES. IF RAMPS, STOOPS, STAIRS, SIDEWALKS, FLATWORK OR PAVING ARE
<br />q o 6. CHARACTERS SHALL BE 48" MINIMUM ABOVE FINISH FLOOR MEASURED FROM THE BASE OF THE INSTALLED, VERIFY FINAL GRADES SURROUNDING THE NEW CONSTRUCTION AND ADJUST STAIR RISERS, RAMP LENGTHS, LIMITS OF PAVING, ETC. TO
<br />LOWEST TACTILE CHARACTER AND 60 MAXIMUM ABOVE FINISH FLOOR MEASURED FROM THE ACCOMMODATE THE REQUIRED RAMP SLOPE, RISER HEIGHTS OR PAVING AREAS. ALL RAMPS AND STAIRS SHALL MEET ADA-ADAAGS (OR ADOPTED
<br />BASELINE OF THE HIGHEST TACTILE CHARACTER. HANDICAP ACCESSIBILITY REQUIREMENTS). IF THERE IS A CONFLICT IN FIELD CONDITIONS, NOTIFY WALMART CONSTRUCTION MANAGER AND THE
<br />ARCHITECT PRIOR TO THE CONSTRUCTION OR ORDERING OF MATERIALS.
<br />o 7. WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THE SIGN SHALL BE ALONGSIDE THE DOOR AT 8. THE CONTRACTOR SHALL VERIFY THE EXISTING FINISH FLOOR ELEVATION AT ALL NEW OPENINGS OF THE EXISTING BUILDING PRIOR TO ESTABLISHING THE
<br />THE LATCH SIDE. AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN SHALL BE LOCATED ON FINISH FLOOR ELEVATION. TO VERIFY FLOOR ELEVATION, THE CONTRACTOR SHALL REMOVE A SMALL PORTION OF THE BLOCK WALL AT THE PROPOSED
<br />THE INACTIVE LEAF. AT DOUBLE DOORS WITH TWO ACTIVE LEAVES, THE SIGN SHALL BE TO THE OPENING BETWEEN THE EXISTING STORE AND THE ADDITION.
<br />_ RIGHT OF THE RIGHT-HAND DOOR. TACTILE SIGNS ARE PERMITTED ON THE PUSH SIDE OF DOORS 9. NOT USED.
<br />a0 WITH CLOSERS AND WITHOUT HOLD -OPEN DEVICES. SEE ALTERNATE SOLUTIONS FOR OTHER 10. NOT USED.
<br />SCENARIOS. 11. REPORT ANY DISCREPANCIES FOUND IN THE FIELD IMMEDIATELY TO WALMART AND THE ARCHITECT PRIOR TO MAKING ANY STRUCTURAL MODIFICATIONS
<br />STRIPING AT BALER OR ORDERING OF ANY MATERIALS.
<br />STRIPING AT HAZMAT CONTROL SIDE PREFERRED SOLUTION
<br />STRIPING REQUIREMENTS
<br />1. 5" WIDE PAINTED STRIPES (P5) @ 12" ON CENTER, @ 45 DEGREE ANGLE TO 5" WIDE EXTERIOR BOUNDARY LINES
<br />2. IF EXISTING HALLWAY, BALER, COMPACTOR, OR EYEWASH WARNING AREAS ARE PAINTED SOLID OR HAVE INCORRECT PATTERN,
<br />REMOVE EXISTING PAINT AND PAINT PER THE STRIPING CONDITIONS SHOWN HERE.
<br />RESTROOM DOOR SYMBOLS I SYMBOLS LEGEND
<br />=D 1/32"
<br />_RCASE
<br />ERING
<br />=1GHT OF LETTERING
<br />9" MIN. TO 2" MAX.
<br />CORRESPONDING
<br />CONTRACTED
<br />(GRADE 2) BRAILLE
<br />SIGNS & IDENTIFICATION
<br />1. THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE THE STANDARD USED TO IDENTIFY FACILITIES THAT ARE
<br />ACCESSIBLE TO AND USABLE BY PHYSICALLY DISABLED PERSONS AS SET FORTH IN TITLE III AND AS SPECIFICALLY
<br />REQUIRED IN THIS SECTION.
<br />2. THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL CONSIST OF A WHITE FIGURE ON A BLUE BACKGROUND. THE
<br />BLUE SHALL BE EQUAL TO COLOR NO. 15090 IN FEDERAL STANDARD 595C.
<br />3. FOR CHARACTER PROPORTION, THE UPPERCASE LETTER "0" SHALL BE USED TO DETERMINE THE ALLOWABLE
<br />WIDTH OF ALL CHARACTERS OF A FONT. THE WIDTH OF THE UPPERCASE LETTER "0" OF THE FONT SHALL BE 55
<br />PERCENT MINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE UPPERCASE LETTER "I".
<br />4. MINIMUM CHARACTER HEIGHT SHALL COMPLY WITH 2O10 ADA TABLE 703.5.5. VIEWING DISTANCE SHALL BE
<br />MEASURED AS THE HORIZONTAL DISTANCE BETWEEN THE CHARACTER AND AN OBSTRUCTION PREVENTING
<br />FURTHER APPROACH TOWARDS THE SIGN. CHARACTER HEIGHT SHALL BE BASED ON THE UPPERCASE LETTER "I".
<br />CHARACTER HEIGHT MEASURED FROM THE BASELINE OF THE CHARACTER SHALL BE 5/8" (16 MM) MINIMUM AND 2
<br />INCHES (51 MM) MAXIMUM.
<br />5. CHARACTERS AND SYMBOLS SHALL CONTRAST WITH THEIR BACKGROUND.
<br />6. WHEN RAISED CHARACTERS OR SYMBOLS ARE USED, THEY SHALL CONFORM TO THE FOLLOWING:
<br />A. CHARACTERS SHALL BE RAISED 1/32" MINIMUM AND SHALL BE SANS -SERIF UPPERCASE CHARACTERS. RAISED
<br />LETTERS SHALL BE DUPLICATED IN BRAILLE.
<br />B. RAISED CHARACTERS SHALL BE A MINIMUM OF 5/8" HIGH AND 2" MAXIMUM BASED ON THE HEIGHT OF THE LETTER
<br />„1"
<br />C. PICTORIAL SYMBOL SIGNS (PICTOGRAMS) SHALL HAVE TEXT DESCRIPTORS LOCATED DIRECTLY BELOW THE
<br />PICTOGRAM FIELD. PICTOGRAMS SHALL HAVE A FIELD HEIGHT OF 6" MINIMUM. PICTOGRAMS AND THEIR FIELDS
<br />SHALL HAVE A NON -GLARE FINISH. PICTOGRAMS SHALL CONTRAST THEIR FIELDS, WITH EITHER A LIGHT
<br />PICTOGRAM ON A DARK FIELD OR A DARK PICTOGRAM ON A LIGHT FIELD.
<br />7. CONTRACTED (GRADE 2) BRAILLE SHALL BE USED WHEREVER BRAILLE IS REQUIRED. DOTS SHALL BE 0.090" (2.3 MM)
<br />TO 0.100" (2.5 MM) ON CENTER IN EACH CELL WITH 0.241" (6.1 MM) TO 0.300" (7.6 MM) SPACE BETWEEN
<br />CORRESPONDING DOTS IN ADJACENT CELLS. DOTS SHALL BE RAISED A MINIMUM OF 0.025" (0.6 MM) TO 0.037" (0.9
<br />MM) ABOVE THE BACKGROUND.
<br />8. WHEN PERMANENT IDENTIFICATION IS PROVIDED FOR ROOMS AND SPACES, RAISED LETTERS SHALL BE
<br />ACCOMPANIED BY BRAILLE. TACTILE CHARACTERS ON SIGNS SHALL BE LOCATED 48 INCHES (1220 MM) MINIMUM
<br />ABOVE THE FINISH FLOOR OR GROUND SURFACE, MEASURED FROM THE BASE OF THE LOWEST TACTILE
<br />CHARACTER AND 60 INCHES (1525 MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND SURFACE, MEASURED
<br />FROM THE BASELINE OF THE HIGHEST TACTILE CHARACTER. WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THE
<br />SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE A TACTILE SIGN IS PROVIDED AT
<br />DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN SHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A TACTILE
<br />SIGN IS PROVIDED AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO THE RIGHT OF THE
<br />RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THE LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT
<br />SIDE OF DOUBLE DOORS, SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNS CONTAINING TACTILE
<br />CHARACTERS SHALL BE LOCATED SO THAT A CLEAR FLOOR SPACE OF 18 INCHES (455 MM) MINIMUM BY 18 INCHES
<br />(455 MM) MINIMUM, CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY DOOR SWING
<br />BETWEEN THE CLOSED POSITION AND 45 DEGREE OPEN POSITION. EXCEPTION: SIGNS WITH TACTILE CHARACTERS
<br />SHALL BE PERMITTED ON THE PUSH SIDE OF DOORS WITH CLOSERS AND WITHOUT HOLD -OPEN DEVICES.
<br />9. SIGNS TO BE PROVIDED AT ALL PUBLIC MEN, WOMEN, FAMILY AND UNISEX RESTROOMS. ROOM NAME SHALL BE
<br />"RESTROOM" AT UNISEX TOILETS.
<br />f�
<br />X-XX - REFERENCE AT KEYNOTE INDICATOR
<br />10.1 KEYNOTE INDICATOR
<br />A KEYNOTE OR BLOCK OF
<br />X.XX KEYNOTES WITH A LEADER
<br />X.XX ATTACHED APPLY SPECIFICALLY
<br />X.XX TO THE ITEM, AREA, OR SURFACE
<br />TO WHICH THE LEADER IS
<br />SALES POINTING
<br />IN ADDITION TO THE ROOM FINISH
<br />_166-1 SCHEDULE, A KEYNOTE OR BLOCK
<br />X.XX X.XX OF KEYNOTES ATTACHED TO HE
<br />X.XX X.XX ROOM NAME TAG APPLY TO THE
<br />X.XX X.XX ENTIRE ROOM
<br />COLOR INDICATOR
<br />-dddkkb- 2 FULL AND PARTIAL
<br />2-A2 SECTION INDICATOR
<br />-Wdftbl 2 EXTERIOR AND INTERIOR
<br />2-A2 ELEVATION INDICATOR
<br />SALES
<br />F-joo-1
<br />ROOM NAME AND NUMBER
<br />A6 PARTITION TYPE INDICATOR
<br />1001 DOOR INDICATOR
<br />OWINDOW INDICATOR
<br />OTV MONITOR
<br />COLUMN LINE INDICATOR
<br />100'-0" HEIGHT ELEVATION INDICATOR
<br />EL
<br />1000 PLAN ELEVATION INDICATOR
<br />5
<br />A2
<br />1 , ENLARGED DETAIL INDICATOR
<br />5
<br />A2
<br />DETAIL INDICATOR
<br />SIGNS CONTAINING TACTILE I I
<br />CHARACTERS SHALL BE
<br />LOCATED SO THAT THERE IS L - ^ J
<br />AN 18"X18" CLEAR FLOOR
<br />AREA CENTERED ON THE
<br />TACTILE CHARACTERS
<br />ALTERNATE SOLUTIONS
<br />A. WHERE THERE IS NO B. THE REQUIRED SIGNAGE MAY
<br />ALTERNATE LOCATION WALL SPACE ON THE BE INSTALLED SO THAT THE
<br />(NEAREST ADJACENT LATCH SIDE OF A SINGLE CLEAR FLOOR AREA IS BEYOND
<br />WALL, RIGHT HAND SIDE DOOR, OR TO THE RIGHT THE ARC OF ANY DOOR SWING
<br />OF OPENING PREFERRED) SIDE OF DOUBLE DOORS, BETWEEN THE CLOSED POSITION
<br />SIGNS SHALL BE ON THE AND 45 DEGREE OPEN POSITION.
<br />NEAREST ADJACENT
<br />WALL.
<br />LL
<br />C. WHEN SIGN IS REQUIRED AT D. WHERE REFRIGERATED CASES OR
<br />A BANK OF DOORS, PLACE (1) FIXTURES IMPEDE THE REQUIRED
<br />SIGN BETWEEN JAMBS. IF CLEAN FLOOR AREA, MOUNT
<br />JAMB IS NOT WIDE ENOUGH FOR SIGNAGE TO THE END PANEL OF
<br />SIGNAGE, PLACE (1) SIGN AT CASE OR OWNER PROVIDED END
<br />RIGHT SIDE OF BANK OF DOORS. PANEL FOR HALF GONDOLAS AND
<br />E. WHERE WALL STANDARDS
<br />IMPEDE THE REQUIRED
<br />CLEAR FLOOR AREA, MOUNT
<br />SIGN DIRECTLY TO DOOR.
<br />ENSURE DOOR HAS
<br />AUTOMATIC CLOSER AND
<br />DOES NOT HAVE A
<br />HOLD -OPEN DEVICE.
<br />ALTERNATE LOCATION
<br />(NEAREST ADJACENT
<br />WALL, RIGHT-HAND SIDE
<br />OF OPENING PREFERRED)
<br />WALL STANDARD FIXTURES
<br />L
<br />12" MIN
<br />F. AT EGRESS DOORS IN THE
<br />GARDEN CENTER WHERE THERE
<br />IS NOT AMPLE WALL SPACE FOR
<br />SIGNAGE, MOUNT SIGN DIRECTLY
<br />TO DOOR. ENSURE DOOR HAS
<br />AUTOMATIC CLOSER AND DOES
<br />NOT HAVE A HOLD -OPEN DEVICE.
<br />'REFERRED
<br />RIGHT-HAND SIDE,
<br />1DJACENT TO DOOR)
<br />G. AUTOMATIC SLIDING DOOR
<br />LOCATIONS
<br />TACTILE SIGNAGE CANNOT
<br />BE LOCATED ON AUTOMATIC
<br />SLIDING DOOR PANELS.
<br />PANEL WIDTH TO MATCH
<br />=PTH OF WAREHOUSE RACK
<br />EXT 0
<br />I p
<br />w z
<br />J Q O
<br />0- Q
<br />O ;f, w L
<br />J
<br />LU
<br />ELEVATION PLAN
<br />H. WHERE WAREHOUSE RACKS IMPEDE THE REQUIRED CLEAR FLOOR AREA
<br />ADJACENT TO THE DOOR, PROVIDE 3/8" A-B PLYWOOD PANEL WITH EASED
<br />EDGES AND ATTACH TO THE END OF THE WAREHOUSE RACK USING (4)
<br />GALVANIZED CARRIAGE BOLTS, WASHERS AND LOCKNUTS. CARRIAGE BOLTS
<br />ARE TO BE SIZED PROPERLY TO ENSURE THE BOLT END DOES NOT
<br />PROTRUDE BEYOND THE TOP OF LOCKNUT AND PANEL IS SECURE. IN
<br />GROCERY SERVICE AND PREPARATION AREAS, PAINT PLYWOOD P33 UNO.
<br />GENERAL CONSTRUCTION REQUIREMENTS:
<br />1. ALL WORK SHALL BE DONE IN A SAFE AND WORKMANLIKE MANNER AND IN STRICT ACCORDANCE WITH THE LOCAL AND/OR STATE (IF APPLICABLE) BUILDING
<br />CODES, NATIONAL ELECTRIC CODE, ADA-ADAAG AND OTHER ADOPTED ACCESSIBILITY STANDARDS, OSHA, AND ALL APPLICABLE CODES, REGULATIONS,
<br />ORDINANCES AND AUTHORITIES HAVING JURISDICTION (AHJ).
<br />2. PROVISIONS REGARDING THE USE OF GAS AND DIESEL EQUIPMENT WITHIN AN ENCLOSED BUILDING, FORMERLY INCLUDED IN THIS PARAGRAPH, ARE NOW
<br />INCLUDED IN SECTION 01351 - REGULATORY COMPLIANCE
<br />3. PROVISIONS REGARDING CORDS FOR ELECTRICAL EQUIPMENT AND ROUTING OF EQUIPMENT CORDS AND HOSES, FORMERLY INCLUDED IN THIS
<br />PARAGRAPH, ARE NOW INCLUDED 1N SECTION 01351 - REGULATORY COMPLIANCE
<br />4. EACH SUBCONTRACTOR IS RESPONSIBLE FOR HAVING A THOROUGH KNOWLEDGE OF ALL DRAWINGS AND SPECIFICATIONS IN THEIR RELATED FIELD. THE
<br />FAILURE TO REVIEW THESE DOCUMENTS DOES NOT RELIEVE THE SUBCONTRACTOR OF ANY RESPONSIBILITY FOR PERFORMING WORK PROPERLY. NO
<br />ADDITIONAL COMPENSATION SHALL BE ALLOWED BECAUSE OF CONDITIONS THAT OCCUR DUE TO FAILURE TO FAMILIARIZE WORKERS WITH THIS
<br />KNOWLEDGE.
<br />5. THE EXISTING BUILDING SHALL BE PROTECTED FROM MOISTURE, DUST AND DEBRIS. INSTALL DUST PARTITIONS OR DRAPES AS REQUIRED AND/OR AS
<br />DIRECTED BY WALMART CONSTRUCTION MANAGER TO KEEP DUST AND MOISTURE FROM THE OPERATING AREAS OF THE STORE.
<br />6. ANY DAMAGE TO WALMART'S PROPERTY, WHICH OCCURS DURING THE PROCESS OF CONSTRUCTION SHALL BE REPAIRED/REPLACED AT NO ADDITIONAL
<br />COST TO WALMART; THIS INCLUDES ALL MERCHANDISE. CONTRACTOR SHALL PAY THE COST FOR ALL DAMAGED MERCHANDISE.
<br />7. THE CONTRACTOR SHALL MAINTAIN THE INTEGRITY OF THE EXISTING BUILDING SECURITY AT ALL TIMES. THIS INCLUDES KEEPING THE BUILDING SECURE
<br />FROM PERSONS, ENVIRONMENTAL ELEMENTS OR HAZARDS. THE CONTRACTOR SHALL BE RESPONSIBLE TO MAINTAIN THE INTEGRITY OF ALL EXISTING
<br />SECURITY SYSTEMS. THE CONTRACTOR SHALL OBTAIN PERMISSION FROM THE STORE MANAGER PRIOR TO THE MODIFICATION OF ANY EXISTING SECURITY
<br />SYSTEM FOR THE OPENING (DEMOLITION) OF ANY EXTERIOR WALL.
<br />8. THE CONTRACTOR SHALL KEEP THE WORK AREA CLEAN AND FREE OF DEBRIS AND REMOVE ALL TRASH AND DEBRIS FROM THE CONSTRUCTION AREA
<br />DAILY. NO FLAMMABLE MATERIALS OR LIQUIDS MAYBE STORED IN THE EXISTING BUILDING OR IN ANY NEW ADDITION.
<br />9. REMOVE ANY EXISTING EQUIPMENT, FIXTURES, FURNISHINGS, ACCESSORIES, SERVICES, FINISHES OR SURFACES AS REQUIRED SHOWN OR NOT SHOWN,
<br />FOR THE INSTALLATION OF NEW CONSTRUCTION. PROVIDE FURRING FOR CONDUITS AND PIPING, SHOWN OR NOT, AND FINISH OUT FURRING TO MATCH
<br />ADJACENT EXISTING FINISHES.
<br />10. REPAIR, RE-ROUTE, AND EXTEND ALL SERVICES, PIPING, CONDUIT OF EXISTING ITEMS AND EQUIPMENT AS REQUIRED DURING THE CONSTRUCTION
<br />PROCESS TO MAINTAIN NORMAL STORE OPERATIONS AND AS REQUIRED FOR THE INSTALLATION OF NEW CONSTRUCTION. THIS INCLUDES ALL ITEMS
<br />SHOWN OR NOT SHOWN ON THE DRAWINGS. RESET EXISTING EQUIPMENT, FIXTURES, FURNISHINGS, ACCESSORIES OR RELATED ITEMS AS REQUIRED FOR
<br />PROPER OPERATION.
<br />11. WHEN EQUIPMENT, FIXTURES, FURNISHINGS, ACCESSORIES, SERVICES, FINISHES OR SURFACES ARE TEMPORARILY REMOVED OR RELOCATED IN ORDER
<br />TO PERFORM WORK, THE CONTRACTOR IS RESPONSIBLE FOR RETURNING THEM TO THEIR ORIGINAL POSITION, RECONNECTION OF SERVICES AND
<br />APPROPRIATE MEANS OF ATTACHMENT UNLESS SPECIFICALLY DIRECTED TO DO OTHERWISE.
<br />12. WHERE EXISTING FINISHES ARE TO REMAIN, CLEAN, REPAIR, PATCH AND REPAINT AS NECESSARY TO BLEND IN WITH ADJACENT WORK. COORDINATE WITH
<br />WALMART CONSTRUCTION MANAGER
<br />13. THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE TIMELY ORDERING OF MATERIALS TO PROHIBIT DELAYS OF THE CONSTRUCTION SCHEDULE OF THIS
<br />PROJECT. IT IS THE RESPONSIBILITY OF THE CONTRACTOR TO COORDINATE DELIVERY OF MATERIALS IN A TIMELY MANNER.
<br />14. IT IS IMPERATIVE THAT THE ROOF FRAMING, DECKING AND ROOFING SYSTEM BE COMPLETED IMMEDIATELY UPON THE DEMOLITION OF THE EXTERIOR WALL
<br />TO ELIMINATE POTENTIAL WATER DAMAGE OR MOISTURE INFILTRATION. THE CONTRACTOR SHALL KEEP THE BUILDING WATERTIGHT AT ALL TIMES.
<br />15. THE GENERAL CONTRACTOR SHALL RESPOND TO ALL REQUIREMENTS OF THE STRUCTURAL ENGINEER/ARCHITECT FOR VERIFICATIONS, RESPONSES, AND
<br />SUBMISSIONS.
<br />16, IF MODIFICATION TO SPRINKLER SYSTEM IS REQUIRED THE GENERAL CONTRACTOR SHALL HIRE A LICENSED SPRINKLER CONTRACTOR. CONTRACTOR TO
<br />SUBMIT SIGNED AND SEALED SPRINKLER DRAWINGS FOR APPROVAL PRIOR TO ANY ALTERATION OF THE AUTOMATIC SPRINKLER SYSTEM. WORK TO BE
<br />DONE UNDER SEPARATE PERMIT.
<br />17. NOT USED.
<br />18. MUD AND DEBRIS TRACKED ONTO OWNER PAVING OR CITY STREETS TO BE CLEANED IMMEDIATELY.
<br />19. BUILDING COMPONENTS AFFECTED BY THE SCOPE OF WORK AND ALLOWED TO REMAIN SHALL BE SECURED TO PREVENT FALLING, LOOSENING, OR
<br />CREATING DAMAGE OF ANY KIND IN THE FUTURE.
<br />DEMOLITION REQUIREMENTS:
<br />1. ALL DEMOLITION SHALL BE CARRIED OUT IN A SAFE MANNER AND IN STRICT ACCORDANCE WITH OSHA REGULATIONS.
<br />2. THE CONTRACTOR SHALL FIELD VERIFY THE EXTENT OF DEMOLITION. THE WORK INCLUDES, BUT IS NOT LIMITED TO, THE DEMOLITION AND REMOVAL OF
<br />WALLS, DOORS, FIXTURES, PLUMBING, PAVING, MECHANICAL AND ELECTRICAL ITEMS INCLUDING CONDUITS AND DUCTWORK AS SHOWN ON DRAWING OR
<br />AS REQUIRED FOR THE INSTALLATION OF THE NEW WORK FOR A COMPLETE JOB.
<br />3. WHEN UTILITIES ARE REMOVED, CAP AND SEAL A MINIMUM OF 8" BELOW FINISH FLOOR OR A MINIMUM OF 6" ABOVE FINISH CEILING.
<br />4. WHEN REMOVING EXISTING STRUCTURAL ITEMS, IT IS THE CONTRACTOR'S RESPONSIBILITY TO PROVIDE ADEQUATE SHORING, BRACING AND SUPPORT
<br />SYSTEMS TO KEEP THE EXISTING STRUCTURE INTACT AND IN A SAFE CONDITION. REFER TO SECTIONS 02023 AND 02251.
<br />5. THE CONTRACTOR MAY NOT REMOVE THE BLOCK WALL IN A PROPOSED OPENING PRIOR TO THE ROOFING SYSTEM OVER THE NEW ADDITION BEING MADE
<br />WATERTIGHT. COORDINATE WITH THE WALMART CONSTRUCTION MANAGER AND THE STORE MANAGER TO SCHEDULE FOR DEMOLITION FOR NEW
<br />OPENINGS.
<br />6. THE CONTRACTOR SHALL REMOVE ANY BUILDING SIGNAGE THAT INTERFERES WITH THE BUILDING ADDITION. WALMART WILL REINSTALL SIGNAGE OR ADD
<br />NEW SIGNAGE AT COMPLETION OF ADDITION.
<br />7. NOTES INDICATING DEMOLITION WORK ARE NOT CONFINED SOLELY TO THE DEMOLITION PLANS. THE GENERAL CONTRACTOR SHALL REVIEW ALL
<br />CONSTRUCTION DOCUMENTS, INCLUSIVE OF SCHEDULES AND SPECIFICATIONS, TO DETERMINE FULL EXTENT OF DEMOLITION WORK.
<br />ABBREVIATION LEGEND
<br />GENERAL ABBREVIATIONS
<br />ABBR
<br />DEFINITION
<br />AB
<br />ANCHOR BOLT
<br />ACI
<br />AMERICAN CONCRETE INSTITUTE
<br />ACRYL
<br />ACRYLIC
<br />ADA
<br />AMERICANS WITH DISABILITIES ACT
<br />ADJ
<br />ADJACENT
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />AFG
<br />ABOVE FINISHED GRADE
<br />AISC
<br />AMERICAN INSTITUTE OF STEEL CONSTRUCTION
<br />ARCH
<br />ARCHITECTURAL
<br />ASTM
<br />AMERICAN SOCIETY OF TESTING AND MATERIALS
<br />AWS
<br />AMERICAN WELDING SOCIETY
<br />►�iP�l
<br />CU
<br />CONDENSING UNIT
<br />DIA
<br />DIAMETER
<br />DSD
<br />DIRECTS SHIPPING DELIVERY
<br />EAS
<br />ELECTRONIC ARTICLE SURVEILLANCE
<br />EDC
<br />ELECTRICAL DISTRIBUTION CENTER
<br />EIFS
<br />EXTERIOR INSULATION AND FINISH SYSTEM
<br />EF
<br />EXHAUST FAN
<br />EJ
<br />EXPANSION JOINT
<br />EL
<br />ELEVATION
<br />ELEC
<br />ELECTRICAL
<br />EQ
<br />EQUAL
<br />ETR
<br />EXISTING TO REMAIN
<br />EW
<br />EACH WAY
<br />EWC
<br />ELECTRIC WATER COOLER
<br />FDN
<br />FOUNDATION
<br />FF
<br />FINISHED FLOOR
<br />FRP
<br />FIBER REINFORCED PLASTIC
<br />FS
<br />FAR SIDE
<br />FTG
<br />FOOTING
<br />FV
<br />FIELD VERIFY
<br />GR
<br />GROCERY
<br />GYP BD
<br />GYPSUM BOARD
<br />HC
<br />HANDICAP
<br />HDTV
<br />HIGH DEFINITION TELEVISION
<br />HORIZ
<br />HORIZONTAL
<br />HSA
<br />HEADED STUD ANCHOR
<br />HSS
<br />HOLLOW STRUCTURAL SECTION
<br />HT
<br />HEIGHT
<br />INFO
<br />INFORMATION
<br />ISO
<br />ISOLATION
<br />JBE
<br />JOIST BEARING ELEVATION
<br />JST
<br />JOIST
<br />JT
<br />JOINT
<br />KSI
<br />KIPS PER SQUARE INCH
<br />L
<br />LENGTH
<br />LB
<br />POUNDS
<br />LLH
<br />LONG LEG HORIZONTAL
<br />LLV
<br />LONG LEG VERTICAL
<br />LONG
<br />LONGITUDINAL
<br />MAX
<br />MAXIMUM
<br />MAU
<br />MECHANICAL AIR UNIT
<br />E
<br />MASONRY ELEVATION
<br />MECH
<br />MECHANICAL
<br />MEP
<br />MECHANICAL ELECTRICAL PLUMBING
<br />MFR
<br />MANUFACTURER
<br />MIN
<br />MINIMUM
<br />MISC
<br />MISCELLANEOUS
<br />MO
<br />MASONRY OPENING
<br />MTL
<br />METAL
<br />NTS
<br />NOT TO SCALE
<br />OC
<br />ON CENTER
<br />OD
<br />OUTSIDE DIAMETER
<br />OH
<br />OPPOSITE HAND
<br />PAF
<br />POWDER ACTUATED FASTENER
<br />PCF
<br />POUNDS PER CUBIC FOOT
<br />PFC
<br />PAINT FIX, CLEAN
<br />PL
<br />PLATE
<br />PLAM
<br />PLASTIC LAMINATE
<br />PLAST
<br />PLASTIC
<br />PLF
<br />POUNDS PER LINEAR FOOT
<br />PMEJ
<br />PREMOLDED EXPANSION JOINT
<br />PSF
<br />POUNDS PER SQUARE FOOT
<br />PSI
<br />POUNDS PER SQUARE INCH
<br />PVC
<br />POLYVINYL CHLORIDE
<br />QTY
<br />QUANTITY
<br />RC
<br />REFRIGERATION CONTRACTOR
<br />REF
<br />REFER TO
<br />REINF
<br />REINFORCING
<br />REQD I
<br />REQUIRED
<br />SIGNAGE LEGEND S►m SIMILARcUnirv�li�u1�
<br />SJI STEEL JOIST INSTITUTE
<br />SPECS SPECIFICATIONS
<br />SS STAINLESS STEEL
<br />STD STANDARD
<br />SIGN STRUC STRUCTURAL
<br />L J 00 T&B TOP AND BOTTOM
<br />p TEMP TEMPERED
<br />SIGN, REF NOTE 3. THK THICKNESS
<br />FF TO TOP OF
<br />TOC/TC TOP OF CONCRETE
<br />1. REQUIRED ACCESSIBLE ELEMENTS SHALL BE IDENTIFIED BY THE INTERNATIONAL SYMBOL OF ACCESSIBILITY AT THE TOF TOP OF FOOTING
<br />FOLLOWING LOCATIONS: TOGB TOP OF GRADE BEAM
<br />A. ACCESSIBLE ENTRANCES WHERE NOT ALL ENTRANCES ARE ACCESSIBLE TOM TOP OF MASONRY
<br />B. ACCESSIBLE ROOMS WHERE MULTIPLE SINGLE -USER TOILETS ARE CLUSTERED AT A SINGLE LOCATION TOP/TP TOP OF PAVING
<br />C. ACCESSIBLE CHECK-OUT AISLES WHERE NOT ALL AISLES ARE ACCESSIBLE. THE SIGN, WHERE PROVIDED, SHALL BE ABOVE TOS TOP OF STEEL
<br />THE CHECK-OUT AISLE IN THE SAME LOCATION AS THE CHECK-OUT AISLE NUMBER OR TYPE OF CHECK-OUT TRANS TRANSVERSE
<br />IDENTIFICATION TYP TYPICAL
<br />D. UNISEX TOILET AND BATHING ROOMS UNO UNLESS NOTED OTHERWISE
<br />E. ACCESSIBLE DRESSING, FITTING AND LOCKER ROOMS WHERE NOT ALL SUCH ROOMS ARE ACCESSIBLE VCPFC VISION CENTER PAINT FIX CLEAN
<br />2. DIRECTIONAL SIGNAGE INDICATING THE ROUTE TO THE NEAREST LIKE ACCESSIBLE ELEMENT SHALL BE PROVIDED AT THE VERT VERTICAL
<br />FOLLOWING LOCATIONS. THESE DIRECTIONAL SIGNS SHALL INCLUDE THE INTERNATIONAL SYMBOL OF ACCESSIBILITY: W WIDTH
<br />A. AT EACH SEPARATE -SEX TOILET INDICATING THE LOCATION OF THE NEAREST UNISEX TOILET WM WALMART
<br />3 TACTILE
<br />URE FS ROM THE BASE OF THE D48 INCHES ( 1220 MM) MINIMUM ABOVE THE ( LOW T TACIHEINCHESLE ARAC R AND 60 CHES 115 5 MM MAX MUMSH FLOOR OR O UND SURFACE,
<br />M ASABOVE HE FINISH DEFINITION LEGEND
<br />FLOOR OR GROUND SURFACE, MEASURED FROM THE BASELINE OF THE HIGHEST TACTILE CHARACTER. WHERE A TACTILE
<br />SIGN IS PROVIDED AT A DOOR, THE SIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE A TACTILE
<br />SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGN SHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A FINAL MERCHANDISE PLAN - FINALIZED MERCHANDISE PRINT FROM WM
<br />TACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TO THE RIGHT OF THE ALSO REFERRED TO AS THE DEAL BOX COPY
<br />RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THE LATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF
<br />DOUBLE DOORS, SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNS CONTAINING TACTILE CHARACTERS
<br />SHALL BE LOCATED SO THAT A CLEAR FLOOR SPACE OF 18 INCHES (455 MM) MINIMUM BY 18 INCHES (455 MM) MINIMUM,
<br />CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OF ANY DOOR SWING BETWEEN THE CLOSED
<br />POSITION AND 45 DEGREE OPEN POSITION. EXCEPTION: SIGNS WITH TACTILE CHARACTERS SHALL BE PERMITTED ON THE
<br />PUSH SIDE OF DOORS WITH CLOSERS AND WITHOUT HOLD -OPEN DEVICES.
<br />4. CHARACTER AND SYMBOLS OF SIGNS SHALL BE IN CONTRAST WITH THEIR BACKGROUND AND SHALL BE EGGSHELL, MATTE, OR
<br />OTHER NON -GLARE MATERIALS OR FINISHES.
<br />5. ACCESSIBLE SIGNAGE SHALL USE GRADE 2 BRAILLE AND MUST COMPLY WITH [CC A117.1 SECTION 703.4 OR ADA SECTION 703.3.
<br />aw
<br />c6 5 O Q W m 2 Q
<br />fnOWPt-W�
<br />LL
<br />w
<br />¢° �wozoWxoaN
<br />aN��W-wU)U
<br />tzOwow ¢
<br />O
<br />IL
<br />it "� ain¢ax¢�
<br />0<U)-I-x2~ .Lu =
<br />aaxcn
<br />0
<br />�E;,WNaFW,9D�walw.o°
<br />~
<br />zLLgaoaLLOW-1�XO �
<br />J�VO�ZW
<br />Vd'}U3LL�<
<br />awmD 2zwa)
<br />woUwZzUzz
<br />!�-p T¢z0WL.0Oa ou
<br />(n
<br />HOWdOa F-liwdmF
<br />m
<br />a
<br />rn
<br />00
<br />L
<br />It
<br />04
<br />rn
<br />Lo
<br />C=) J c�
<br />co
<br />0 O
<br />`L �
<br />1_J
<br />^ C
<br />C! ) N
<br />O
<br />=
<br />0
<br />ry
<br />Gig�_=O
<br />d
<br />11 C)can
<br />NO
<br />Z
<br />S
<br />N
<br />W
<br />iY
<br />0
<br />=m0
<br />W
<br />NM
<br />r�
<br />ti
<br />w
<br />m
<br />z
<br />m
<br />0
<br />ISSUE BLOCK
<br />CHECKED BY:
<br />RD
<br />DRAWN BY:
<br />AJB
<br />PROTO CYCLE:
<br />09/25/20
<br />DOCUMENT DATE:
<br />11/06/20
<br />GENERAL
<br />INFORMATION
<br />SHEET:
<br />Nl
<br />
|