|
NEW PANEL "A" SCHEDULE
<br />PANEL RATING:
<br />200
<br />LOCATION:
<br />BREAK VOLTS: 208
<br />PHASE: 3
<br />WIRE: 4
<br />HZ:
<br />60
<br />MLO:
<br />200
<br />MAIN AIC:
<br />22,000 BR.AIC: 10,000
<br />ENCL: NEMA 1
<br />MTG.: SURFACE
<br />DESCRIP. OF
<br />BRANCH
<br />BREAKER
<br />VA/PHASE
<br />CKT
<br />PHASE
<br />CKT
<br />VA/PHASE
<br />BREAKER
<br />BRANCH
<br />DESCRIP. OF
<br />W
<br />G
<br />C
<br />A
<br />P
<br />A
<br />B
<br />C
<br />A
<br />B
<br />C
<br />A
<br />P
<br />W
<br />G
<br />C
<br />LOAD SERVED
<br />NO.
<br />A B C
<br />NO.
<br />LOAD SERVED
<br />EXISTING RTU (4T)
<br />10
<br />10
<br />3/4" 35 3
<br />4,203 1
<br />2 1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 1
<br />- - -
<br />- - -
<br />-- - --
<br />4,203 3
<br />4
<br />1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 2
<br />- - -
<br />- - -
<br />- - -
<br />- - - - - - - - -
<br />4,203 5
<br />6
<br />1,200 20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 3
<br />EXISTING RTU (5T)
<br />8
<br />10
<br />3/4" 45 3
<br />4,803 7
<br />8 1,200
<br />1 20 1
<br />1 12
<br />12
<br />3/4"
<br />XRAY 4
<br />- - -
<br />- - -
<br />- - -
<br />- - - - - - - - -
<br />4,803 9
<br />10
<br />1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 5
<br />---
<br />---
<br />-
<br />- - - - - - -
<br />4,803 11
<br />12
<br />1,200 20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 6
<br />AIR COMPRESSOR
<br />12
<br />12
<br />3/4" 20 2
<br />874 1 13
<br />14 1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 7
<br />- - -
<br />- - -
<br />--
<br />- - - - - -
<br />874 15
<br />16
<br />1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 8
<br />VACUUM PUMP
<br />12
<br />12
<br />3/4" 20 2
<br />697 17
<br />18
<br />1,200 20 1
<br />12
<br />12
<br />3/4"
<br />UC-1,2,3
<br />- - -
<br />---
<br />- - -
<br />- - - - - - - - -
<br />697 19
<br />20 1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />UC-6,7,8
<br />WATER HEATER
<br />10
<br />10
<br />3/4" 30 2
<br />2,250 21
<br />22
<br />800
<br />20 1
<br />12
<br />12
<br />3/4"
<br />UC-4,5
<br />- - -
<br />- - -
<br />- - -
<br />- -- - - -
<br />2,250 23
<br />24
<br />1,200 20 1
<br />12
<br />12
<br />3/4"
<br />XRAY 9
<br />STERILIZER
<br />12
<br />12
<br />3/4" 20 1
<br />1,200 25
<br />26 1,200
<br />20 1
<br />12
<br />12
<br />3/4"
<br />TRIMMER
<br />AUTOCLAVE
<br />12
<br />12
<br />3/4" 20 1
<br />1,2001 27
<br />28
<br />600
<br />20 1
<br />12
<br />12
<br />3/4"
<br />WATER FILTER
<br />ULTRASONIC
<br />12
<br />12
<br />3/4" 20 1 1
<br />1,200 29
<br />30
<br />SPACE
<br />TOTAL VA/PHASE
<br />11,777 13,330 13,153
<br />6,000
<br />5,000
<br />4,800 TOTAL VA/PHASE
<br />17,777
<br />Oil
<br />17,953 TOTAL VA
<br />NOTES:
<br />1.
<br />AIC RATINGS ARE
<br />MINIMUM SYMMETRICAL AMOUNTS. REVERIFY AVAILABLE SHORT CIRCUIT
<br />WITH LOCAL
<br />UTILITY
<br />PRIOR TO PREPARING
<br />SUBMITTALS AND INCREASE CAPACITY AS NECESSARY.
<br />2.
<br />PROVIDE HACR TYPE
<br />CIRCUIT BREAKERS FOR ALL ITEMS IN THIS PANEL.
<br />3.
<br />NOTE THAT THIS SCHEDULE INDICATES NEW LOADS ONLY. OTHER EXISTING ITEMS
<br />MAY BE PRESENT -
<br />FIELD VERIFY.
<br />4.
<br />ALL OUTLETS IN KITCHEN AREAS SHALL BE GFCI PROTECTED
<br />PER NEC.
<br />5.
<br />* INDICATES EXISTING
<br />BRANCH CIRCUIT TO REMAIN.
<br />6.
<br />DEMAND LOAD CALCULATION: ITEM
<br />LOAD
<br />FACTOR
<br />DEMAND
<br />LIGHTING
<br />0 x
<br />125%
<br />= 0.0
<br />RECEPTS < 10,000 VA
<br />0 x
<br />100%
<br />= 0.0
<br />RECEPTS > 10,000 VA
<br />0 x
<br />50%
<br />= 0.0
<br />EQUIPMENT
<br />27,D42 x
<br />100%
<br />= 27,042.0
<br />HVAC (GREATER)
<br />27,018 x
<br />100%
<br />= 27,018.0
<br />TOTAL DEMAND LOAD (VA)
<br />= 54,060.0
<br />TOTAL DEMAND AMPERES
<br />= 150.1
<br />TOTAL CONNECTED AMPERES
<br />= 150.1
<br />NEW PANEL "B" SCHEDULE
<br />PANEL
<br />RATING:
<br />200
<br />LOCATION:
<br />BREAK VOLTS: 208
<br />PHASE: 3
<br />WIRE: 4
<br />HZ:
<br />60
<br />MLO:
<br />200
<br />MAIN AIC:
<br />22,000 BR.AIC: 10,000
<br />ENCL: NEMA 1
<br />MTG.: SURFACE
<br />DESCRIP.
<br />OF
<br />BRANCH
<br />BREAKER
<br />VA/PHASE
<br />CKT
<br />PHASE
<br />CKT
<br />VA/PHASE
<br />BREAKER
<br />BRANCH
<br />DESCRIP. OF
<br />W
<br />G
<br />C
<br />A
<br />P
<br />A
<br />B
<br />C
<br />A
<br />B
<br />C
<br />A
<br />P
<br />W
<br />G
<br />C
<br />LOAD SERVED
<br />NO.
<br />A B C
<br />NO.
<br />LOAD SERVED
<br />REC. -
<br />TRIAGE 1
<br />& 2
<br />12
<br />12
<br />3/4" 20 1
<br />1,080 1
<br />2 1,500
<br />20 1
<br />10
<br />10
<br />3/4"
<br />MICROWAVE
<br />REC. -
<br />TRIAGE 3
<br />& 4
<br />12
<br />12
<br />3/4" 20 1
<br />1,080 3
<br />4 1,000
<br />20 1
<br />12
<br />12
<br />3/4"
<br />DISPOSER
<br />REC. -
<br />TRIAGE 5
<br />& 6
<br />12
<br />12
<br />3/4" 20 1
<br />1,080 5
<br />6
<br />600 20 1
<br />12
<br />12
<br />3/4"
<br />WATER COOLER
<br />REC. -
<br />TRIAGE 7
<br />& 8
<br />12
<br />12
<br />3/4" 20 1
<br />1,080 7
<br />8 1,200
<br />20 1
<br />12 1
<br />12
<br />3/4"
<br />REFRIGERATOR
<br />REC. -
<br />WAITING
<br />12
<br />12
<br />3/4" 20 1
<br />900 9
<br />10 1,165
<br />20 1
<br />12
<br />12
<br />3/4"
<br />LTG. - LEFT
<br />REC. -
<br />BUSINESS
<br />OFF
<br />12
<br />12
<br />3/4" 20 1
<br />720 11
<br />12
<br />1,200 20 1
<br />12
<br />12
<br />3/4"
<br />1 LTG. - SIGN
<br />REC. -
<br />BATHROOMS
<br />12
<br />12
<br />3/4" 20 1
<br />5401 13
<br />14 990
<br />20 1
<br />12
<br />12
<br />3/4"
<br />LTG. - RIGHT
<br />REC. -
<br />ADMIN
<br />12
<br />12
<br />3/4" 20 1
<br />720 15
<br />16 1,790
<br />20 1
<br />12
<br />12
<br />3/4"
<br />LTG. - FRONT
<br />REC. -
<br />LAB
<br />12
<br />12
<br />3/4" 20 1
<br />720 17
<br />18
<br />1,440 20 1
<br />12
<br />12
<br />3/4"
<br />REC. - CORRIDOR
<br />REC. -
<br />OFFICE
<br />12
<br />12
<br />3/4" 20 1
<br />540 19
<br />20
<br />20 1
<br />- - -
<br />- - -
<br />- - -
<br />SPARE
<br />REC. -
<br />BREAK ROOM
<br />12
<br />12
<br />3/4" 20 1
<br />540 21
<br />22
<br />20 1
<br />- - -
<br />- - -
<br />- - -
<br />SPARE
<br />REC. -
<br />STERIL 1
<br />12
<br />12
<br />3/4" 20 1
<br />540 23
<br />24
<br />SPACE
<br />REC. -
<br />NETWORK
<br />1
<br />12
<br />12
<br />3/4" 20 1
<br />360 1 25
<br />26
<br />SPACE
<br />REC. -
<br />STERIL 2
<br />12
<br />12
<br />3/4" 20 1
<br />720 27
<br />28
<br />SPACE
<br />REC. -
<br />NETWORK
<br />2
<br />12
<br />12
<br />3/4" 20 1 1
<br />1 360 29
<br />30
<br />SPACE
<br />TOTAL VA/PHASE
<br />1 3,600 3,960 3,420
<br />3,690 3,955
<br />3,240 TOTAL VA/PHASE
<br />7,290 7,915
<br />6,660 TOTAL VA
<br />NOTES:
<br />1.
<br />AIC RATINGS ARE
<br />MINIMUM SYMMETRICAL AMOUNTS. REVERIFY AVAILABLE SHORT CIRCUIT
<br />WITH LOCAL
<br />UTILITY
<br />PRIOR TO PREPARING
<br />SUBMITTALS AND INCREASE CAPACITY AS NECESSARY.
<br />2.
<br />PROVIDE HACR TYPE
<br />CIRCUIT BREAKERS FOR ALL ITEMS IN THIS
<br />PANEL.
<br />3.
<br />NOTE THAT THIS SCHEDULE INDICATES NEW LOADS ONLY. OTHER
<br />EXISTING ITEMS MAY BE PRESENT -
<br />FIELD VERIFY.
<br />4.
<br />ALL OUTLETS IN KITCHEN AREAS SHALL BE GFCI PROTECTED
<br />PER NEC.
<br />5.
<br />* INDICATES EXISTING BRANCH CIRCUIT TO REMAIN.
<br />6.
<br />DEMAND LOAD CALCULATION: ITEM
<br />LOAD FACTOR
<br />DEMAND
<br />LIGHTING
<br />5,145 x 125%
<br />= 6,431.3
<br />RECEPTS < 10,000 VA
<br />10,000 x 100%
<br />= 10,000.0
<br />RECEPTS > 10,000 VA
<br />2,420 x 50%
<br />= 1,210.0
<br />EQUIPMENT
<br />4,300 x 100%
<br />= 4,300.0
<br />HVAC (GREATER)
<br />0 x 100%
<br />= 0.0
<br />TOTAL DEMAND LOAD (VA)
<br />= 21,941.3
<br />TOTAL DEMAND AMPERES
<br />= 60.9
<br />TOTAL CONNECTED AMPERES
<br />= 60.7
<br />ELECTRICAL SPECIFICATIONS:
<br />1. GENERAL
<br />A. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT REQUIRED FOR A COMPLETE SYSTEM AS OUTLINED IN THE
<br />CONTRACT DRAWINGS AND THESE SPECIFICATIONS.
<br />B. NOTE THAT DRAWINGS ARE DIAGRAMMATIC ONLY AND INTENDED TO SHOW THE GENERAL ARRANGEMENT OF
<br />SYSTEMS, NOT EVERY MINUTE DETAIL.
<br />C. DO NOT SCALE PLANS.
<br />D. PROVIDE ALL NECESSARY FITTINGS, BOXES, TRANSITIONS, CONNECTORS, ETC. WHETHER SHOWN OR NOT ON
<br />PLANS.
<br />E. ALL WORK IS NEW UNLESS OTHERWISE NOTED.
<br />F. THESE PLANS REPRESENT THE DESIGN INTENT BASED ON INFORMATION AVAILABLE AT THE TIME OF DESIGN. ANY
<br />SUBSTANTIAL MODIFICATIONS OR ALTERATIONS MADE DURING THE CONSTRUCTION PHASE SHALL BE REPORTED TO
<br />THE ENGINEER PRIOR TO WORK. MODIFICATIONS MADE WITHOUT THE ENGINEER'S WRITTEN APPROVAL SHALL REMAIN
<br />THE RESPONSIBILITY OF THE CONTRACTOR.
<br />G. IN CASE OF ANY DISCREPANCIES BETWEEN THE DRAWINGS, SPECIFICATIONS, FIELD CONDITIONS, CODES, ETC. IT
<br />IS THE RESPONSIBILITY OF THE CONTRACTOR TO REFER ALL SUCH MATTERS TO THE ENGINEER IN WRITING
<br />IMMEDIATELY FOR RESOLUTION PRIOR TO EXECUTING ANY WORK. ANY WORK PERFORMED WITHOUT THE WRITTEN
<br />AUTHORIZATION OF THE ENGINEER SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR.
<br />H. ALL WORK SHALL CONFORM TO THE FOLLOWING CODES (AS APPLICABLE) AS WELL AS ALL LOCAL REGULATIONS,
<br />ORDINANCES, AND AMENDMENTS :
<br />2007 FLORIDA BUILDING CODE W/ 2009 SUPPLEMENT
<br />2008 NFPA-70 NATIONAL ELECTRICAL CODE
<br />2005 NFPA-72 NATIONAL FIRE ALARM CODE
<br />2. SCOPE OF WORK
<br />PROVIDE A COMPLETE NEW ELECTRICAL SYSTEM, INCLUDING ELECTRICAL SERVICE, POWER, LIGHTING, SITE LIGHTING,
<br />ETC.
<br />3. ITEMS FURNISHED BY CONTRACTOR
<br />IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO PROVIDE ALL MATERIALS, EQUIPMENT, AND
<br />ACCESSORIES NECESSARY TO MAKE A COMPLETE INSTALLATION. ALL EQUIPMENT SHALL BE STORED IN A SAFE, DRY
<br />PLACE IN THE MANUFACTURER'S ORIGINAL PACKAGING UNTIL READY FOR USE. THE OWNER SHALL NOT BE
<br />RESPONSIBLE FOR PROVIDING ANY PART OF THE PROJECT, UNLESS SPECIFICALLY NOTED. THE CONTRACTOR SHALL
<br />ALSO BE RESPONSIBLE FOR PAYING ALL REQUIRED FEES, OBTAINING ALL PERMITS, AND ARRANGING FOR ALL
<br />INSPECTIONS, INCLUDING COORDINATION WITH AND SATISFYING ALL REQUIREMENTS OF THE ELECTRICAL UTILITY
<br />COMPANY(IES) AS MAY BE REQUIRED TO EXECUTE THIS SCOPE OF WORK.
<br />4. WORK IN EXISTING BUILDINGS
<br />A. DO NOT USE POWDER DRIVEN FASTENERS OF ANY TYPE.
<br />B. ALL ITEMS REMOVED AND NOT RE -USED SHALL BE TURNED OVER TO THE OWNER. CONTRACTOR SHALL REMOVE
<br />ANY UNSATISFACTORY ITEMS FROM THE PROJECT SITE.
<br />C. SOME EXISTING ITEMS TO REMAIN WITHOUT WORK ARE SHOWN FOR CLARITY OR REFERENCE ONLY. NOTE THAT
<br />ADDITIONAL ITEMS WITHOUT WORK MAY ALSO BE PRESENT.
<br />D. DRAWINGS OF EXISTING SYSTEMS ARE BASED ON EXISTING DOCUMENTS AND FIELD CONDITIONS, SOME OF
<br />WHICH MAY BE UNVERIFIED. PRIOR TO SUBMITTING A BID, CONTRACTOR SHALL STUDY THE PLANS AND VISIT THE
<br />PROJECT SITE IN ORDER TO BECOME FAMILIAR WITH EXISTING CONDITIONS. ANY DISCREPANCIES IN THE CONTRACT
<br />DOCUMENTS WHICH COULD SIGNIFICANTLY IMPACT THE PROJECT BUDGET OR SCHEDULE MUST BE REPORTED TO
<br />THE ENGINEER IN WRITING IMMEDIATELY. FAILURE TO DO SO WILL NOT BE SUFFICIENT CAUSE FOR DELAYS OR
<br />CHANGES LATER IN THE PROJECT.. CHANGE ORDERS RESULTING FROM FAILURE TO PROPERLY INVESTIGATE EXISTING
<br />FIELD CONDITIONS WILL NOT BE ACCEPTED. ALL WORK IS NEW UNLESS OTHERWISE NOTED.
<br />E. MODIFICATIONS TO EXISTING SYSTEMS NECESSARY TO CONNECT TO NEW WORK SHALL BE CONSIDERED TO BE
<br />PART OF THE BASIC WORK OF THIS CONTRACT.
<br />F. COORDINATE ALL WORK SCHEDULES WITH THE OWNER TO MINIMIZE DISRUPTIONS TO EXISTING SYSTEMS OUTSIDE
<br />THIS SCOPE OF WORK.
<br />5. COORDINATION
<br />ALL WORK ON THIS PROJECT SHALL BE COORDINATED WITH THE OWNER AND ALL OTHER TRADES PRIOR TO
<br />BEGINNING AY WORK OR ORDERING ANY MATERIALS. CONTRACTOR SHALL REVIEW PLANS OF ALL DISCIPLINES
<br />INVOLVED AND ADVISE THE ARCHITECT IN WRITING OF ANY CONFLICTS, CODE OR SAFETY ISSUES THAT MAY EXIST
<br />PRIOR TO ANY FABRICATION OR ORDERING OF EQUIPMENT. RESOLUTION OF SUCH CONFLICTS WHICH ARE NOT
<br />REPORTED PRIOR TO CONSTRUCTION SHALL REMAIN THE RESPONSIBILITY OF THE CONTRACTOR AND CHANGE ORDER
<br />PROPOSALS FOR SUCH WORK WILL NOT BE ACCEPTED. PROVIDE ROUTING AND OFFSETS NECESSARY TO AVOID
<br />CONFLICTS WITH STRUCTURE, FINISHES, AND WORK OF OTHERS. CONTRACTOR SHALL PROVIDE ALL CORE
<br />PENETRATIONS AND PATCHING FOR FLOOR PENETRATIONS.
<br />6. DEVICE LOCATIONS
<br />A. INSTALL ALL DEVICES IN ACCESSIBLE LOCATIONS, EXCEPT AS SPECIFICALLY NOTED OR PROHIBITED BY NEC.
<br />B, PROVIDE MIN. 18x18 INCH PAINTED ALUMINUM ACCESS DOORS WITH FULL HINGE AND KEY, FOR ACCESS TO
<br />ALL ELECTRICAL DEVICES, PULL BOXES, JUNCTION BOXES, AND ACCESSORIES IN PLASTER, DRYWALL, OR
<br />INACCESSIBLE CEILINGS, OR IN WALLS. GROUP DEVICES AT A SINGLE LOCATION, AS AVAILABLE.
<br />C. ACCESS DOORS IN RATED WALLS OR CEILINGS SHALL HAVE A RATING AT LEAST EQUAL TO THE RATING OF THE
<br />WALL OR CEILING.
<br />D. ALL DEVICES, RACEWAYS, ETC. WHICH ARE EXPOSED SHALL BE PAINTED TO MATCH THE ADJACENT SURFACE OR
<br />AS DIRECTED BY THE ARCHITECT.
<br />E. ALL ELECTRICAL EQUIPMENT SHALL BE INSTALLED A MINIMUM OF 1'-O" ABOVE THE BASE FLOOD ELEVATION.
<br />7. EQUIPMENT GENERAL
<br />ALL EQUIPMENT OF EACH TYPE SHALL BE BY ONE MANUFACTURER AND SHALL HAVE CHARACTERISTICS AS LISTED
<br />IN THE EQUIPMENT SCHEDULES. ALL EQUIPMENT SHALL BE UL LISTED, NO EXCEPTIONS ! SUBSTITUTIONS ARE
<br />ACCEPTABLE PROVIDED THAT THE SUBSTITUTED EQUIPMENT HAS EQUIVALENT CHARACTERISTICS AS THAT SCHEDULED
<br />AND IS PROVIDED BY AN ACCEPTABLE MANUFACTURER AS LISTED FOR THAT EQUIPMENT TYPE. CONTRACTOR SHALL
<br />SUBMIT PRODUCT DATA FOR ALL EQUIPMENT TO THE ENGINEER FOR APPROVAL PRIOR TO ORDERING. SUBMITTALS
<br />SHALL INCLUDE DIMENSIONS, WEIGHT, VOLTAGE, AMPERAGE, HORSEPOWER, POWER FACTOR, INTERRUPTING CAPACITY,
<br />ETC.
<br />8. CONDUCTORS
<br />A. PROVIDE ONLY DUAL RATED THWN-2/THHN-2 COPPER CONDUCTORS. MINIMUM SIZE IS NUMBER 12 AWG
<br />B. CONDUCTORS SHALL HAVE COLORED INSULATION FOR IDENTIFICATION PURPOSES AS FOLLOWS:
<br />240/208/120V 480 277V
<br />PHASE A BLACK BROWN
<br />PHASE B RED ORANGE
<br />PHASE C BLUE YELLOW
<br />NEUTRAL WHITE NATURAL GREY
<br />GROUND GREEN GREEN W/ YELLOW STRIPE
<br />C. GROUNDED CONDUCTORS WHICH CARRY OVER 250V TO GROUND SHALL BE TAGGED WITH VOLTAGE AT EACH
<br />TERMINATION POINT.
<br />D. DO NOT INSTALL MORE THAN THREE CURRENT CARRYING CONDUCTORS IN SINGLE RACEWAY (NOT INCLUDING
<br />NEUTRAL) WHICH WILL REQUIRE NEC TABLE 310-16 NOTE 8 DERATING.
<br />E. PHASE AND GROUNDING CONDUCTOR SIZES SHALL BE INCREASED AS NECESSARY TO ACCOUNT FOR VOLTAGE
<br />DROP.
<br />LIGHTING FIXTURE SCHEDULE
<br />TAG
<br />LAMPS
<br />FIXTURE
<br />NOTES
<br />QTY
<br />TYPE
<br />DESC.
<br />MOUNTING
<br />VOLTS/O/Hz
<br />VA
<br />2x4 LENSED TROFFER
<br />A
<br />2
<br />FLUOR.
<br />32W, T-8
<br />GRID
<br />120/1 /60
<br />70
<br />GRID MOUNTED
<br />HIGH EFF. ELEC. BALLAST
<br />DECORATIVE PENDENT
<br />B
<br />1
<br />CF
<br />30W MR16
<br />PENDENT
<br />120/1/60
<br />30
<br />OVER DESK BY
<br />OWNER
<br />6" RECESSED CAN WITH
<br />C
<br />1
<br />CIF
<br />32W, TRT
<br />RECESSED
<br />120/1/60
<br />40
<br />BAFFLE & DIFFUSE REFLECTOR
<br />HIGH EFF. EELC. BALLAST
<br />ROUND LENSED UTILITY
<br />D
<br />1
<br />INCAND.
<br />60W A-19
<br />SURFACE
<br />120/1/60
<br />60
<br />LIGHT FOR MECH
<br />ROOM.
<br />COMBO EGRESS/EXIT SIGN
<br />X
<br />1
<br />LED
<br />5W LED
<br />SURFACE
<br />120/1/60
<br />5
<br />W/ RED LETTERS
<br />AND 90 MIN. BATTERY PACK
<br />1. PROVIDE NORTH FACING PHOTOCELL AND LIGHTING CONTACTORS AS NECESSARY TO OPERATE
<br />L COMMON EXTERIOR LIGHT FIXTURES SIMULTANEOUSLY EXCEPT EXIT AND EGRESS LIGHTI G AL L ( LIGHTING).
<br />2. EXIT SIGNS AND EGRESS LIGHTING SHALL HAVE 90 MINUTE BATTERY BACKUP AND SHALL NOT BE SWITCHED.
<br />3. PROVIDE OCCUPANCY SENSORS OR TIME CLOCK FOR AUTOMATIC CONTROL IN ALL SPACES.
<br />PROVIDE NECESSARY ACCESSORIES SUCH AS RELAYS, CONTACTORS, SENSORS, OVERRIDES, ETC.
<br />4. ALL EXTERIOR LIGHT FIXTURES SHALL BE DAMP OR WET LOCATION LISTED.
<br />9. RACEWAYS
<br />A. INSTALL ALL WIRING ABOVE GROUND IN METALLIC CONDUIT (EMT INDOORS, RGS OUTDOORS OR IN EXPOSED
<br />LOCATIONS).
<br />B. ALL EXPOSED RACEWAYS SHALL BE RUN PARALLEL TO WALLS OR CEILINGS AND SHALL BE PAINTED TO
<br />MATCH ADJACENT SURFACES OR AS DIRECTED BY THE OWNER.
<br />C. WHERE MULTIPLE RACEWAYS ARE RUN EXPOSED, RUN ALL RACEWAYS SQUARE AND PARALLEL IN A NEAT
<br />AND ORDERLY MANNER.
<br />D. MAKE FINAL CONNECTIONS (NOT MORE THAN 6'-0" LONG) TO ALL EQUIPMENT WITH FLEXIBLE METALLIC
<br />CONDUIT (DRY LOCATIONS) OR LIQUID TIGHT FLEXIBLE METALLIC CONDUIT (DAMP OR WET LOCATIONS).
<br />E. INSTALL ALL WIRING BELOW GROUND IN RIGID NON-METALLIC CONDUIT (SCHEDULE 40 PVC). ALL EXTERIOR
<br />NONMETALLIC CONDUITS SHALL BE UV RESISTANT. ALL CONDUITS RUN BELOW GROUND SHALL BE INSTALLED
<br />ACCORDING TO NEC300-5.
<br />F. TYPE MC CABLE MAY BE USED AS AN ALTERNATIVE TO CONDUCTORS IN METAL RACEWAY IN DRY INDOOR
<br />LOCATIONS, PROVIDED IT IS INSTALLED PER NEC AND APPROVED BY THE AUTHORITY HAVING JURISDICTION.
<br />G. METALLIC CONDUITS SHALL NOT BE USED AS GROUNDING CONDUCTORS. PROVIDE A SEPARATE GROUNDING
<br />CONDUCTOR IN ALL METALLIC CONDUITS, BONDED AT BOTH ENDS PER NEC.
<br />10. GROUNDING
<br />A. ALL ELECTRICAL SYSTEMS SHALL BE PROPERLY GROUNDED PER NEC 250,
<br />B. EXPOSED GROUNDING ELECTRODE CONDUCTORS SHALL BE PROTECTED BY RIGID NONMETALLIC CONDUITS,
<br />MIN SIZE = J".
<br />C. PROVIDE GROUNDING ELECTRODE CONDUCTORS TO DRIVEN GROUND RODS AT THE BASE OF ALL LIGHT
<br />POLES, REMOTE BUILDINGS, OR REMOTE EQUIPMENT.
<br />D. ALL METAL ITEMS OF THE ELECTRICAL SYSTEM INCLUDING RACEWAYS, BOXES, FIXTURES, ETC. SHALL BE
<br />BONDED AND PROPERLY GROUNDED.
<br />11. SWITCHBOARDS AND PANEL BOARDS
<br />A. PROVIDE SWITCHBOARDS AND PANEL BOARDS, SIZE AND ARRANGEMENT AS INDICATED ON PLANS AND
<br />SCHEDULES.
<br />B. MOUNT PANEL BOARDS NOT MORE THAN 48" A.F.F. TO CENTER.
<br />C. ENCLOSURES SHALL BE SUITABLE FOR THE ENVIRONMENT IN WHICH THEY ARE INSTALLED (NEMA 1
<br />INDOORS, NEMA 3R OUTDOORS, ETC.)
<br />D. PROVIDE A TYPEWRITTEN PANEL SCHEDULE IDENTIFYING THE FUNCTION OF ALL CIRCUIT BREAKERS IN A
<br />CLEAR PLASTIC SLEEVE PERMANENTLY ATTACHED TO THE PANEL BOARD COVER.
<br />E. ALL SWITCHBOARDS AND PANEL BOARDS SHALL HAVE A THERMOPLASTIC IDENTIFYING NAMEPLATE
<br />PERMANENTLY AFFIXED TO THE FRONT OR COVER.
<br />F. PROVIDE ONE 1" EMPTY CONDUIT FROM PANEL TO 6" ABOVE CEILING FOR EVERY (3) SPARES OR SPACES.
<br />G. PANEL BOARDS AND SWITCHBOARDS BY: SQUARE D, CUTLER HAMMER, OR GE.
<br />12. CIRCUIT BREAKERS
<br />A. ALL CIRCUIT BREAKERS SHALL BE BY A SINGLE MANUFACTURER, WITH SAME STYLE AND WITHSTAND RATING
<br />TO MATCH THE PANEL IN WHICH THEY ARE INSTALLED.
<br />B. PROVIDE MULTIPLE POLE CIRCUIT BREAKERS FOR MULTIPLE POLE CIRCUITS. HANDLE TIES ARE NOT
<br />PERMITTED.
<br />C. PROVIDE HACR TYPE CIRCUIT BREAKERS FOR ALL HVAC EQUIPMENT AND WATER HEATERS.
<br />D. PROVIDE GROUND FAULT CIRCUIT INTERRUPTER BREAKERS FOR ALL OUTDOOR, BATHROOM, AND KITCHEN
<br />BRANCH CIRCUITS WHICH DO NOT UTILIZE GFCI RECEPTACLES, OR AS OTHERWISE REQUIRED BY THE
<br />AUTHORITY HAVING JURISDICTION.
<br />E. NOT USED.
<br />F. NOT USED.
<br />G. PROVIDE INVERSE TIME CIRCUIT BREAKERS FOR MOTORS UNLESS SPECIFIED OTHERWISE.
<br />H. CIRCUIT BREAKERS SHALL BE PROVIDED WITH INDICATING ON/OFF HANDLES.
<br />J. CIRCUIT BREAKERS FOR FIRE ALARMS SHALL BE LOCKABLE.
<br />K. CIRCUIT BREAKERS BY: SQUARE D, CUTLER HAMMER, OR GE.
<br />13. DEVICES
<br />A. PROVIDE GALVANIZED STEEL BOXES FOR ALL DEVICES IN EXPOSED LOCATIONS OR RECESSED INTO RATED
<br />WALLS.
<br />B. PROVIDE THERMOPLASTIC OR GALVANIZED STEEL BOXES FOR ALL DEVICES TO BE RECESSED INTO
<br />NON -RATED WALLS.
<br />C. FINISH OF ALL DEVICES AND COVER PLATES SHALL BE AS DIRECTED BY THE OWNER IN WRITING PRIOR TO
<br />ORDERING.
<br />D. ALL RECEPTACLES SHALL BE OF THE GROUNDING TYPE.
<br />E. ALL RECEPTACLES SHALL BE 20 AMP, 120 VOLT RATED, COMMERCIAL GRADE.
<br />F. PROVIDE DISCONNECT SWITCHES (WITH OR WITHOUT FUSES AS SPECIFIED) IN ENCLOSURES SUITABLE FOR
<br />THE ENVIRONMENT IN WHICH THEY ARE INSTALLED (NEMA 1 INDOORS, NEMA 3R OUTDOORS & AT WATER
<br />HEATER, ETC.)
<br />G. ALL SWITCHES AND RECEPTACLES BY LEVITON, GE, OR EQUIVALENT.
<br />H. PROVIDE GFCI RECEPTACLES IN ALL KITCHENS, BATHROOMS, GARAGES, OUTSIDE, OR WHEREVER ELSE
<br />SHOWN ON DRAWINGS. LABEL ALL DEVICES DOWNSTREAM OF GFCI DEVICE AS "GFCI PROTECTED". PROVIDE AT
<br />LEAST ONE DUPLEX GFCI PROTECTED RECEPTACLE IN A WEATHERPROOF ENCLOSURE WITHIN TWENTY FIVE (25)
<br />FEET OF ALL ROOF OR GRADE MOUNTED EXTERIOR HVAC EQUIPMENT.
<br />J. FOR GFCI RECEPTACLES NOT ON A DEDICATED BRANCH CIRCUIT (SUCH AS OUTDOOR RECEPTACLES
<br />CONNECTED TO THE NEAREST INTERIOR CIRCUIT), MAKE EVERY ATTEMPT TO LOCATE THE GFCI RECEPTACLE AT
<br />THE END OF THE CIRCUIT RUN SO AS TO MINIMIZE THE POSSIBILITY OF CAUSING NUISANCE POWER LOSS TO
<br />OTHER DEVICES WHEN THE GFCI DEVICE TRIPS.
<br />14. LIGHTING
<br />A. ALL LIGHT FIXTURES SHALL BE THOSE DESCRIBED IN THE LIGHTING FIXTURE SCHEDULE OR THEIR
<br />EQUIVALENT AS APPROVED BY THE ENGINEER PRIOR TO ORDERING. IF ALTERNATE FIXTURES ARE USED, IT
<br />SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO COORDINATE THEIR INSTALLATION DETAILS WITH ALL
<br />OTHER TRADES WITH REGARD TO SPACE REQUIRED, WIRING, POWER CONSUMPTION, ETC.
<br />B. LIGHTING BRANCH CIRCUITS SHALL NOT BE LOADED TO MORE THAN 80% OF THE CIRCUIT BREAKER
<br />AM PAC ITY.
<br />C. ALL LIGHT FIXTURES INSTALLED IN DAMP, WET, OR HAZARDOUS (CLASSIFIED) LOCATIONS SHALL BE LISTED
<br />FOR SUCH USE.
<br />D. INCANDESCENT LAMPS SHALL NOT BE USED EXCEPT FOR DIMMING PURPOSES OR AS OTHERWISE STATED
<br />ON PLANS OR PERMITTED BY THE AUTHORITY HAVING JURISDICTION.
<br />E. ALL FLUORESCENT OR HID LIGHT FIXTURES SHALL BE FUSED WITH ELECTRONIC BALLAST AS REQUIRED TO
<br />MEET THE SWITCHING REQUIREMENTS DESCRIBED ELSEWHERE IN THESE DOCUMENTS OR THE AUTHORITY HAVING
<br />JURISDICTION. PROVIDE MULTIPLE BALLASTS WHERE REQUIRED TO PROVIDE MULTIPLE LIGHTING LEVELS TO
<br />COMPLY WITH APPLICABLE ENERGY CODES.
<br />F. INTERIOR LIGHTING IN ALL BUILDINGS LARGER THAN 5,000 SQUARE FEET SHALL BE PROVIDED WITH
<br />AUTOMATIC CONTROLS. CONTROLS SHALL CONSIST OF A CENTRAL TIME -OF -DAY SCHEDULING CONTROLLER OR
<br />OCCUPANCY SENSORS LOCATED IN EACH SPACE. OCCUPANCY SENSORS SHALL BE LOCATED SO THE OCCUPANT
<br />CAN SEE THE CONTROLLED LIGHTING AND SHALL BE CAPABLE OF A 4 HOUR OVERRIDE. LIGHTING CONTROL
<br />ZONES SHALL NOT EXCEED 2,500 SQUARE FEET.
<br />G. PROVIDE TIME CLOCKS OR NORTH FACING PHOTOCELLS TO CONTROL ALL EXTERIOR LIGHTING CIRCUITS
<br />AUTOMATICALLY. PROVIDE LIGHTING CONTACTORS AS REQUIRED.
<br />H. ALL EXIT SIGNS AND EMERGENCY EGRESS LIGHTING SHALL NOT BE SWITCHED AND SHALL HAVE BATTERY
<br />BACKUP OR BE CONNECTED TO THE EMERGENCY POWER SYSTEM.
<br />15. WARRANTIES AND MAINTENANCE
<br />A. ALL EQUIPMENT SHALL BE STARTED, TESTED, ADJUSTED, LUBRICATED, CLEANED, AND PLACED IN GOOD
<br />Of
<br />OPERATING CONDITION BY THE CONTRACTOR. CONTRACTOR SHALL GUARANTEE ALL EQUIPMENT, MATERIALS, AND
<br /><
<br />WORKMANSHIP TO BE FREE OF DEFECTS FOR A PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE BY
<br />Z
<br />THE OWNER AND THE CONTRACTOR SHALL REPAIR ANY SUCH DEFECTS AT NO COST TO THE OWNER. ALL
<br />EQUIPMENT INCLUDED IN THE PROJECT SHALL BE COVERED BY THE MANUFACTURER'S WARRANTY FOR THE
<br />DURATION OF THAT WARRANTY. COPIES OF ALL MANUFACTURER'S WARRANTIES AND CONTRACTOR WARRANTIES
<br />N
<br />SHALL BE PROVIDED TO THE OWNER AT FINAL ACCEPTANCE.
<br /><
<br />B. CONTRACTOR SHALL MEET WITH THE OWNER'S REPRESENTATIVE AND REVIEW ALL OPERATIONS AND
<br />MAINTENANCE OF ALL SYSTEMS. CONTRACTOR SHALL PROVIDE THE OWNER WITH BOUND COPIES OF ALL
<br />Z
<br />OPERATION AND MAINTENANCE MANUALS INCLUDING PARTS LISTS, MAINTENANCE SCHEDULES, ETC.
<br /><
<br />C. THE CONTRACTOR SHALL CONTINUALLY RECORD ANY AND ALL DEVIATIONS TO THE CONTRACT DOCUMENTS
<br />MADE DURING CONSTRUCTION AND PROVIDE A COMPLETE SET OF THESE RECORD DRAWINGS TO THE OWNER
<br />WITHIN 30 DAYS OF COMPLETION OF CONSTRUCTION. IF REQUIRED BY THE AUTHORITY HAVING JURISDICTION, IT
<br />SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO SECURE THE SERVICES OF A LICENSED PROFESSIONAL
<br />z_
<br />ENGINEER TO PROVIDE SIGNED AND SEALED RECORD DRAWINGS.
<br />z
<br />16. TESTING
<br />w
<br />A. AT THE COMPLETION OF THE PROJECT, TEST ALL ELECTRICAL EQUIPMENT AND DEVICES FOR PROPER
<br />o
<br />OPERATION. TEST FOR GROUNDS AND SHORTS. REPORT ALL RESULTS TO THE ARCHITECT IN WRITING. REPLACE
<br />N
<br />ANY DEFECTIVE DEVICES OR EQUIPMENT.
<br /><
<br />B. TEST ALL FIRE ALARMS, GENERATORS, AND OTHER LIFE SAFETY EQUIPMENT IN THE PRESENCE OF THE
<br />ENGINEER AND THE FIRE OFFICIAL TO DEMONSTRATE OPERATION. MAKE ANY MODIFICATIONS NECESSARY AS
<br />o
<br />REQUIRED BY THE FIRE OFFICIAL AND REPAIR OR REPLACE ANY DEFECTIVE ITEMS AS NECESSARY.
<br />o
<br />N
<br />LD
<br />o
<br />U
<br />DCH PROJECT NUMBER: 11-002
<br />ISSUE
<br />DATE
<br />REVIEW
<br />1 /27/11
<br />PERMIT
<br />1 /27/11
<br />REV.
<br />REV.
<br />REV.
<br />REV.
<br />THESE DOCUMENTS, DESIGNS, NOTES, DETAILS AND
<br />SPECIFICATIONS AND CONCEPTS ARE THE SOLE
<br />PROPERTY OF FRAZE DESIGN, INC. AND SHALL NOT BE
<br />REPRODUCED, RE -USED OR COPIED FOR OTHER
<br />PROJECTS, IN WHOLE OR PART WITHOUT THE WRITTEN
<br />CONSENT OF FRANK FRAZE, ARCHITECT, AIA.
<br />ALL RIGHTS ARE RESERVED BY THE ARCHITECT IN
<br />ACCORDANCE WITH U.S. COPYRIGHT AND PATENT
<br />LAWS. UNAUTHORIZED REPRODUCTION WILL BE
<br />PROSECUTED TO THE FULL EXTENT OF THE LAW.
<br />PROFESSIONAL SEAL
<br />1L.EO/V ®®
<br />:® •®® c' SF ®R®• ®��
<br />• 0�
<br />4�.;s'fi 1 '�":,. sue•
<br />VINCEiNi6E)Jif NARDO
<br />FLORIDA P.E. #58009
<br />\\ \ \MvONO
<br />'✓
<br />0 •
<br />•
<br />1'rn
<br />I
<br />••
<br />04,
<br />0
<br />00
<br />rq
<br />•
<br />SHEET TITLE
<br />ELECTRICAL
<br />SPECIFICATIONS
<br />SHEET
<br />NUMBER
<br />
|