Laserfiche WebLink
' ' 1 L I- 1 '11 l <br />IGT. <br />R. <br />c0 ` <br />00 <br />LEFT ELEVATION <br />SCALE: 3/16" = 1'-0" <br />RIGHT ELEVATION <br />SCALE: 3/16" = 1'-0" <br />General Notes <br />ROOF CRITERIA: <br />12" OVERHANG U.N.O. <br />PLUMB CUT FASCIA ROOF <br />PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />txterior luovering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />N O <br />U N <br />N S 4] �G <br />o LL <br />`? ,P <br />A-1 <br />t� <br />Z <br />— <br />�- (D r -, <br />c; <br />N a: �. <br />O O <br />C U <br />.4 <br />O W <br />N <br />O <br />N <br />0 <br />N <br />N <br />a��'tiiay��E•11tt1�taP�'1f <br />N0 F7 <br />fr <br />OF <br />•"io6..�t` <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />H� <br />CODQ ce)(Co <br />N <br />LL <br />N Ol rip <br />, 0 C J , <br />0 ao °� ve " <br />y rjnr�� LL W a <br />a - <br />a��v : x <br />�LLL. WaL <br />Z <br />Z5^ <br />O <br />Z 13 <br />10 <br />L M O v W <br />r6 A W O J <br />_ <br />W r°�°'°i a- C e <br />?' N Z K N O <br />ILL a <br />Z OU USN <br />M <br />V <br />z 04 <br />z � <br />z <br />^ M <br />W <br />z O <br />U <br />GN <br />N <br />.0 <br />g <br />�O <br />w <br />to c �, <br />�N r <br />' w � <br />t 8 <br />U <br />_ <br />0 <br />o <br />W <br />M <br />z � <br />o <br />Z <br />� <br />a E <br />0 <br />Wa <br />Q® <br />O <br />" <br />X U <br />4 <br />O <br />U <br />O ro <br />N t <br />z <br />o <br />ao <br />W z <br />• � <br />N C <br />_ C <br />." <br />�m <br />mi <br />o <br />o <br />Z� <br />Z <br />N J <br />cb <br />aw <br />M ZZ <br />r� 22 <br />o <br />a <br />2 <br />a <br />W <br />T <br />U <br />zg <br />�� <br />�LL <br />it <br />F� <br />FZ <br />p <br />Z <br />S2r <br />�0 <br />ax <br />F� <br />il�d <br />ov 3 <br />c <br />T <br />N <br />ai <br />rn <br />N <br />f.9 <br />CN <br />CM <br />co <br />O <br />W <br />GV <br />M <br />L6 <br />Ln <br />° <br />N <br />O <br />�- <br />f) m <br />O <br />00 <br />r <br />4= <br />"� M <br />N <br />F— <br />O <br />N <br />00 <br />04 <br />J L0 N <br />L0 <br />00 <br />T <br />N N <br />r <br />N <br />7 O i6 <br />O <br />Z <br />Z <br />E 0 d <br />C <br />a <br />G <br />U ¢ O <br />JOB <br />NO: 21-17091-17908 <br />SCALE : AS NOTED <br />SHEET NO. <br />9 <br />