Laserfiche WebLink
a <br />a <br />80 <br />60 <br />12 <br />5.01 <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />c— HDR, - — <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />FLASHING \k <br />--..... - ....___2S-SH <br />--------- <br />N <br />— — — — — — — — 25_SH_ <br />RAISED BANDS OR FOAM <br />PER COMMUNITY <br />SPECIFICATIONS <br />2ND�.�. _ _— — — — — — — — — — <br />FIN FLR <br />T.O.M. _ _ _. ��. _ :Z _.C. -T_. _ c•, <br />- — — CJ %WEEP c N <br />HDR. - <br />TEXTURED �i0000aaao ��/ oo N <br />/ <br />� u SCORED <br />CEMENTITIOUS El <br />- <br />f 1 STUCCO <br />FINISH ONI �__] F <br />E-7.1 <br />CMU (TYP) �1 J ----J <br />4" N <br />FBI N FLR <br />3 68 <br />FRONT ELEVATION - A <br />SCALE: 1/4" = V-0" <br />9'-0" RIDGE VENT <br />12-- <br />FIBEREGLASS SHINLGE INSTALLED 5.01 <br />AS PER MANUFACTURER-7 -Z <br />SPECIFICATIONS <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />I. <br />12 CJ 25-SH CJ <br />4.01 000007 <br />CJ/WEEP <br />------------------------- <br />r <br />25-SH 25-SH <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />12 <br />— 14.0 <br />RIGHT ELEVATION - A <br />SCALE: 1/4" = V-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.xl-1/2" long (3/4"A" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturers <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water Into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />M <br />N <br />�= <br />O <br />N <br />o <br />'= <br />u� <br />>.0 <br />N <br />cti o <br />V sz cn <br />m <br />i <br />V- ca- <br />y IC O w <br />d o Zi <br />t O <br />Cc <br />E <br />a <br />C, <br />0 <br />w <br />v gR0 W/V <br />­J <br />56CPS <br />SS <br />i. •�i�1 <br />�ll1111111't\\\\\\\\\ <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />0 <br />I- <br />st <br />a e <br />M 8 <br />o 0 V <br />L <br />$'d0Ze� <br />N <br />G <br />S <br />" <br />LL <br />_ <br />LJL I a <br />— a, a x <br />A 0 <br />OL <br />W <br />C w <br />cr <br />t <br />CL0 <br />cc Ci m Lu <br />LO MZ a <br />ZN <br />o t, 0 00 <br />W <br />El 0 <br />U <br />z M <br />z <br />V I <br />n <br />U <br />C5 <br />(3) <br />4- <br />•U <br />N <br />O <br />V) <br />c <br />U % <br />w <br />r <br />i <br />r <br />S� <br />yz <br />g�z <br />Q <br />`_ E <br />O <br />ag <br />1z <br />2a <br />Z <br />C:, <br />t$ <br />az <br />ms <br />z <br />Z <br />7' <br />r <br />20 <br />Z Z <br />o <br />W <br />¢ <br />g0 <br />j <br />0. <br />w <br />&5 <br />�a <br />Qo <br />cl�w <br />k <br />°O <br />= <br />�L <br />J <br />O <br />rn <br />L° <br />M <br />c� <br />L <br />:0 <br />N <br />Cr <br />o. <br />LO <br />Q <br />0 <br />8 <br />cv <br />o <br />LO <br />cn tV <br />a) <br />m <br />O N <br />Lo <br />r <br />Q <br />04 <br />r <br />E <br />M <br />° CO <br />O <br />0 <br />E (� <br />E <br />m <br />Q. <br />U <br />Q p <br />.i <br />JOB <br />NO: <br />23-00515 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.1 <br />