|
FOLD UP WEATHER
<br />RESISTIVE BARRIER &
<br />WEATHER RESISTIVE
<br />BARRIER
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />TEMPORARILY SECURE
<br />WEATHER
<br />DOOR ROUGH OPENING
<br />SLOPE
<br />RESISITIVE
<br />0.3 in: 12.0 in
<br />R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />BARRIER
<br />TAPE EXTERIOR
<br />WOOD FRAME CONSTR.
<br />(0.6 cm : 30.5 cm)
<br />include flashing as described in Section R703.4.
<br />SELF -ADHERED FLASHING 3/4"-1" BEAD OF CONSTR.
<br />a SHEATHING
<br />BY LAPPING DOWN ADHESIVE TO BE APPLIED UNDER
<br />SELF -ADHERED FLASHING
<br />_.
<br />OVER RIM JOIST AND UP THRESHOLD OF DOOR AND
<br />-
<br />WALL BY 6 IN. RETURN UP JAMB 6". USE LIQUID
<br />R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of
<br />naseneLsown"oow - �=
<br />z
<br />NAIL BRAND OR EQUAL WEATHER
<br />EXTERIOR
<br />CEMT. FIN.
<br />water within the wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means
<br />-
<br />PROOF CAULKING
<br />of draining to the exterior water that penetrates the exterior cladding.
<br />WEATHER
<br />SELF -ADHERED FLASHING
<br />BUILDING PAPER
<br />2 ' RESISITIVE
<br />BARRIER
<br />SEAL TOPS OF JOISTS
<br />WI RE LATH
<br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />UNDER DECKING SUBFLOOR
<br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied
<br />=' SELF -ADHERED FLASHING
<br />(SEE DETAIL WP07)
<br />-
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6
<br />r T -''-
<br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The
<br />HEAD FLASHING TIE-IN INSTRUXTIONS:
<br />No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and
<br />1. Cut, fold up & temporarily secure weather
<br />RIM JOIST
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />THESE DETAILS ARE GENERIC AND
<br />resistive barrier above header to allow for
<br />flashing installation
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />2. Self -adhered flashing plus head flashing under ,)
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />,I
<br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over
<br />wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade
<br />BE USED.
<br />2
<br />flashing and seal with tape
<br />2
<br />O
<br />D paper. The individual layers shall be installed independently such that each layer provides a separate continuous lane and an flashing
<br />P P Y P Y Y P P P Y g
<br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW 1
<br />SELF-ADHERED FLASHING
<br />1
<br />SELF -ADHERED FLASHING
<br />1
<br />Exception: Where the barrier that is has
<br />-
<br />EXTERIOR DOOR WITH DECK SECTION A
<br />MT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER
<br />water -resistive applied over wood -based sheathing a water resistance
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />substantially nonwater-absorbing layer or designed drainage space.
<br />EXTERIOR SHEATHING
<br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT
<br />RUBBERIZED
<br />EXTERIOR SHEATHING
<br />�t
<br />3/4"-V BEAD OF CONSTR. INSTALL SELF -ADHERED
<br />ADHESIVE TO BE APPLIED UNDER FLASHING JAMB & HEAD
<br />NEEDED IN CORNERS ADHESIVE
<br />ASPHALT ADHESIVE
<br />THROUGH SELF -ADHERED
<br />R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be
<br />3/8" CEMENT
<br />PLASTER
<br />THRESHOLD OF DOOR AND RETURN FLASHING, SEE
<br />FLASHING SELF -ADHERED FLASHING
<br />applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied
<br />12 MIL DRYLOK CMU -MASONRY BLOCK
<br />UP JAMB L USE LIQUID NAIL BRAND FLANGED (SEE DETAIL
<br />OR EQUAL WEATHER PROOF CAULKING
<br />membranes used as flashingshall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to
<br />PP � 9 PP
<br />EXTREME
<br />REFER TO TECHNICAL
<br />SCORED
<br />prevent the entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />WINDOW
<br />LETTER ON CHEMICAL - ,
<br />COMPATIBILITY
<br />RELEASE PAPER
<br />Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />FASTENER 1) SEALANT AT
<br />SELF -ADHERED FLASHING ° ° °
<br />°
<br />SELF -ADHERED FLASHING,
<br />�� (BEFORE FOLDING, SCORE
<br />PAPER TO
<br />READ
<br />the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />4) SEALANT JOINT � •. '• � ' WINDOW BUCK TO
<br />°
<br />EXTEND A MINIMUM 6"
<br />ESIIVEASSHOLEASE
<br />WN))sE
<br />contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />OUTSIDE EDGE OF '' ' ' : ,' • •' MASONRY
<br />°
<br />VERTICALLY
<br />BOTTOM OF FROM
<br />flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />WINDOW BUCK : e•
<br />2) SEALANT JOINT
<br />•
<br />a ° °
<br />HRESHOLD
<br />' T
<br />n
<br />shall be Installed at the following locations:
<br />5) SEALANT FROM INSIDE EDGE OF
<br />2 •
<br />WINDOW FRAME WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />SECTION -A (SEE DETAIL WP02)
<br />1.1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />AND EXTEND TO WINDOW FRAME
<br />MASONRY ATTACHED
<br />PER CODE
<br />SELF -ADHERED FLASHING
<br />0
<br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />°
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />6) TOOLED SEALANT REQUIREMENTS
<br />BEAD BRIDGING
<br />•
<br />2
<br />following:
<br />CLADDING AND WINDOW
<br />FRAME
<br />z ;:;.
<br />°
<br />SELF -ADHERED FLASHING
<br />5
<br />1.1 The fenestration manufacturer's Installation and flashing instructions, or for applications not addressed in the fenestration
<br />3) SEALANT WINDOW FRAME T
<br />WINDOW BUCK ALL THE WAY
<br />NAILING FLANGE
<br />1
<br />14
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details
<br />AROUND, INCLUDING SILL.
<br />2
<br />SEAL TOPS OF JOISTS
<br />6
<br />are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING 8
<br />UNDER DECKING
<br />2
<br />7
<br />subsequent drainage. Openings usin an flashing shall incorporate flashing or protection at the head and sides.
<br />q 99 P 9 P 9
<br />FLANGE
<br />(SEE DETAIL WP07)
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />1.3 1.3. In accordance with other approved methods.
<br />SCS 06 05 CMU INSTALLATION 6 POINT BUCK AND
<br />SELF -ADHERED FLASHING
<br />1
<br />SELF -ADHERED FLASHING
<br />SELF -ADHERED FLASHING
<br />,
<br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />HALF ROUND WINDOW
<br />EXTERIOR DOOR WITH DECK
<br />INSIDE CORNER
<br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />--,Ground
<br />3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />4.4.Continuously above all projecting wood trim.
<br />SHEATHING
<br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />71- -- - -
<br />1
<br />6.6.At wall and roof intersections.
<br />-_
<br />Water Resistant Barrier
<br />7. 7. t built-in gutters.
<br />JAMB, SILL AND HEAD DETAIL
<br />Lath
<br />APPROVED
<br />ELF-PATCDHEREDFLASHING
<br />SELF-ADHERED
<br />Sheathing
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />APPROVED
<br />HOUSEWRAPSTRUCTALATH
<br />TWIN TRACK 2.5 -
<br />stucco
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />3/4" CEMENT PLASTER
<br />° ° d
<br />°
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />DOUBLE
<br />°
<br />7/8" Cement Plaster
<br />"V" SEALANT SOCKET WITH
<br />JOIST
<br />°a
<br />°
<br />TOOLED APPROVED SEALANT
<br />SINGLE WOOD BEAM
<br />° °
<br />in accordance with 7/8" Cement Plaster
<br />JOIST BELOW
<br />1 SELF -ADHERED FLASHING
<br />Foundation Wall ° °in
<br />ASTMC926 ce with
<br />SELF -ADHERED FLASHING
<br />a ° a n
<br />ASTMC926
<br />2
<br />Felt backed metal
<br />3" MIN
<br />lathe in accordance Felt backed metal
<br />SELF -ADHERED SELF -ADHERED
<br />4with
<br />ASTMC1063 lathe in accordance
<br />FLASHING FLASHING
<br />O
<br />5
<br />, Building Paper with ASTMC1063
<br />,';� Building Paper
<br />7/16" O.S.B.
<br />7/16" O.S.B.
<br />' sheathing
<br />SCS 0602 WINDOW FIN INTERFACE WITH
<br />SELF -ADHERED FLASHING '
<br />SELF -ADHERED FLASHING
<br />j
<br />FOUNDATION WEEP SCREED
<br />,%
<br />sheathing
<br />Metal ,. sheathing
<br />EXTRUDED SHOULDER
<br />DECK JOIST
<br />OUTSIDE CORNER
<br />Flashing
<br />Weep Screed
<br />SELF -ADHERED FLASHING
<br />2x FRAMEWALL
<br />s Per
<br />Matnulf ct SSpecs.
<br />PRODUCTS DETAILS
<br />> STRIP OF SAF LEGEND
<br />SELF ADHERED FLASHING (SAF)
<br />Maintain Stampede or similar
<br />Bottom of cauk bottom
<br />TILE FINISH
<br />Q
<br />DRAINAGE PLANE WRB DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />Weep Screed joint orllj/
<br />W
<br />BARRIER (WRB) - -
<br />1 1 /2" to 2"
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />1/2" DUROCK
<br />>
<br />BOND BREAK WEATHER RESISTANT BARRIER-
<br />BOND BREAK WRB SELF FURRING (SF) LATH
<br />Weep Screed
<br />Above Roof P
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />¢
<br />I PLASTER ACCESSORY - - - ----
<br />Sheathing Installed As Per
<br />SF LATH SHEATHING,'OSB', PLYWOOD, DENSGLASS
<br />Manufact. Specs.
<br />V-4" PER PLAN
<br />Detail Instructions
<br />Refer to the number marked as # in each detail that corresponds to the
<br />P
<br />numbered items in the list o Ii1StfUCtlOnS belOW:
<br />1'-0"PER PLAN
<br />I WRAP DP WRB ONTO
<br />I THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />1/2" Cementitious
<br />Cement Plaster Decorative Finish
<br />in accordance
<br />BARRIER
<br />with ASTMC926
<br />°'�•o All inside and
<br />1. Install self -adhered flashing in order as shown by numbers
<br />SLOPE
<br />8" CMU
<br />-- -
<br />\\ I 3-1/2" INCH FLANGE
<br />over wood 2nd •0•�'0
<br />°o ,.o , outside corner will
<br />floor •'�•o,o� need to be miter
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />4" OR 8" CMU - ° ° a °
<br />- - - - - -
<br />' ° cut and caulked all
<br />3. Self -adhered flashingcan be substituted for building paper
<br />g p p
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />-
<br />(PER SEAT DEPTH) °
<br />-.--- °=-
<br />FILL WITH GROUT - °
<br />8°
<br />Z Z
<br />a. I a
<br />�� \��.�✓^�.�/�/�/��� � � STRUCTURAL FRAMING
<br />�_� _ _ __ ___ 1
<br />T
<br />�I
<br />'°•o,o, o,••. butt •oints need to
<br />�
<br />•�'• becaulked using
<br />'' • '
<br />' ° ' Stampede
<br />in the layer) ease of installation and to
<br />°
<br />:,, `td STRUCTURAL SHEATHING
<br />• or sim.
<br />embedded adhesive -for
<br />- - °
<br />THIS GAP IS A RESULT OF
<br />caulk for all
<br />minimize scoring cuts
<br />n °
<br />W W
<br />a t1
<br />PLASTER STOP NATURAL SHRINKAGE. STRIP OF SAF
<br />5. Remove all release paper per standard installation instructions and
<br />a ,°
<br />~
<br />_ cn
<br />CONTINUOUS BACKER DO NOT SEAL.
<br />DRAINAGE PLANE WRB
<br />adhere to substrate using a square piece of flashing material (6" X 6"
<br />_
<br />�% U
<br />ROD & SEALANT DRIP SCREED PLASTIC
<br />Minimum)
<br />°
<br />SLOPED MUD BED
<br />W W
<br />= Cr
<br />ACCESSORY I I BOND BREAK WRB
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />- 4
<br />-
<br />¢ W
<br />Lu
<br />(n 3:
<br />SF LATH
<br />fit tight to
<br />VINYL SHOWER PAN _ °
<br />A
<br />corner
<br />° °
<br />a a
<br />U)
<br />II
<br />Note:
<br />8. Mechanically fasten as necessary
<br />Sl-OpE _ _.� °
<br />_ __ a °
<br />The building paper and metal lath must be
<br />Cement installed over the top of the weep screed.
<br />° -
<br />PLASTER STOP A
<br />Plaster
<br />o
<br />over ck
<br />CONTINUOUS BACKER ROD
<br />& S
<br />1 st floor
<br />4
<br />CEMENTITIOUS FINISH
<br />WEEP SCREED DETAIL
<br />SHOWER SEAT
<br />SOFFIT/CANTILEVER '
<br />SCALE: NOT TO SCALE
<br />c-1
<br />C_
<br />N
<br />c
<br />0
<br />d
<br />O �.G
<br />+s
<br />u
<br />x
<br />++ � a
<br />a A O
<br />fl O 1
<br />oCa u s m
<br />to °'
<br />s � �
<br />ia- P
<br />0
<br />N
<br />M
<br />0
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2020 Florida Building Code
<br />-
<br />Residential
<br />7th Edition. Engineer's signature and seal
<br />Is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineers signature and seal.
<br />N
<br />N 0
<br />V ao a R
<br />�NO'�
<br />ry
<br />LL LL M
<br />J U.
<br />Z t ro4 °
<br />� a 0
<br />W NrD
<br />W
<br />W�pm
<br />Z N Cl)z ¢ 0
<br />z OU
<br />W pp
<br />C !
<br />Z N
<br />z
<br />Z � �
<br />w
<br />a
<br />z
<br />V c/ LL
<br />w �
<br />'U W
<br />O LU-�
<br />U
<br />w
<br />'
<br />c)
<br />Q Y
<br />Qc �
<br />o
<br />M
<br />M
<br />=
<br />w
<br />o
<br />sgR
<br />au"
<br />tV l)
<br />C
<br />U�U
<br />O
<br />U O
<br />0
<br />O
<br />Z
<br />g
<br />G
<br />�O
<br />Y
<br />K�
<br />t
<br />rp
<br />NC
<br />O
<br />ZLL
<br />Z
<br />C J
<br />a ^
<br /><w
<br />7W
<br />o�
<br />a�
<br />�o
<br />o
<br />z�
<br />3
<br />0
<br />�
<br />11'
<br />O
<br />C
<br />Co
<br />�
<br />L
<br />T--
<br />� M
<br />j
<br />Y
<br />U)
<br />CV
<br />¢I
<br />04
<br />0
<br />N
<br />o
<br />O
<br />N
<br />�
<br />LO
<br />M
<br />Q
<br />iG
<br />r
<br />o
<br />Z
<br />Z
<br />E �-- �'
<br />�'
<br />o
<br />c
<br />a.
<br />to _J ¢ o
<br />JOB
<br />NO: 22-06464
<br />SCALE : AS NOTED
<br />SHEET NO.
<br />W P
<br />
|