Laserfiche WebLink
, <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />12 -} <br />- — <br />FIBEREGLASS SHINLGE INSTALLED 5.0 -1 <br />AS PER MANUFACTURER _ _-_ _`Jr 4' OFF RIDGE VENTS - <br />SPECIFICATIONS - -� - � � —`_ � <br />- — — <br />HEEL HGT. <br />A Go EXTERIOR <br />50 PLASTER ON <br />loor <br />FRAME <br />25-SH 25-SH CJ FLASHING <br />2ND <br />FLR , <br />35-SH <br />R... I -------------------------- L-1- <br />6068 SGD <br />12 <br />14.0 <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />REAR ELEVATION - B <br />SCALE: 1/4" = 1'-0" <br />9'-0" RIDGE VENT <br />12 <br />5.0�- <br />- - -� - -T - - <br />- , r I- - <br />T <br />I <br />l r j-A- <br />_. <br />- <br />-�,- <br />- - - 7- <br />r <br />. <br />r T A- -- - <br />T <br />_ <br />T <br />T — -- - -_7 - -- - <br />T- <br />T I <br />1 H3-SH <br />24 SH <br />FLASHING <br />12 CJ CJ 12 <br />---- 4_0E— 14.0 <br />CJ/WEEP 1Ci <br />---- -- ---- -------------------------------------------------------------------------------------------- ---- <br />2'-0" <br />1 H3-SH <br />----�--�-----------------------------------------------------------------------------------------------------I---FI <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />LEFT ELEVATION - B <br />SCALE: 1/4" = 1'-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-112" long, <br />16 gage staples, spaced in accordance with ASTM C1063 or <br />C1787, or as otherwise approved. (Refer to sheet SN1 for the <br />engineered method for Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, Gay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, fed shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applie <br />d <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shallcorrosion resistant. <br />Fluid-applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />r= <br />-o <br />21. W <br />J <br />ar o <br />e M C.,., <br />m <br />O L <br />N O CV t <br />H o� <br />N Y <br />3 °'• as <br />d u Q <br />� 3 � <br />-T �+ <br />N SO <br />= E <br />o <br />a 1r <br />`o <br />��� ��ttttl►���sire� <br />,.ti: <br />UJ <br />.p <br />I • 2 <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages beadng <br />Engineer's signature and seal. <br />fA <br />I.- <br />a <br />e} <br />O E S N <br />8 <br />(% <br />o N <br />N O C a, <br />0 <br />46 LL LL <br />NMa� <br />a <br />LL tL iL <br />ii ii C1 <br />Z <br />0 <br />LL z <br />2o, o <br />tr{�_a_ 0 9 <br />�7 N fD m J 6 <br />W <br />pj O1 r <br />Z <br />w <br />Z <br />N MQ !U <br />O U ❑�❑ <br />Z <br />CD <br />z (14 <br />z <br />z <br />a <br />- N <br />(n <br />z N <br />4--+ <br />O <br />—LJJ <br />�tn <br />� <br />w <br />Of <br />Of Y <br />¢ O <br />� Q <br />N D) <br />C <br />o <br />J� <br />w <br />Z <br />M <br />0 � <br />i <br />E <br />zo <br />>n <br />E V <br />t— rt) <br />o° <br />z <br />$ o <br />oa <br />00 <br />ZE <br />n3 <br />�Z <br />6pZ <br />� <br />C fL <br />p <br />W- Z <br />J <br />N Ca <br />a <br />m � <br />o0 <br />= <br />Z <br />m <br />S � <br />U <br />. 0 <br />aZ <br />2z <br />$ <br />ab <br />02 <br />go <br />NZ <br />Q <br />m <br />R F <br />.a <br />a� <br />S F <br />J <br />;Z <br />Q <br />_ <br />a <br />WZ1 <br />�_ <br />° <br />�C:) <br />LO <br />J <br />rn <br />R <br />cM <br />O <br />Co <br />e-- <br />Q <br />ca <br />Y <br />(n <br />C 4 <br />LO <br />N <br />C3i <br />(� <br />cM C) <br />L0 <br />T <br />cM N <br />T <br />T <br />CV)M <br />E <br />7 O <br />W U') <br />Z <br />Z <br />r_ <br />E r <br />E <br />m <br />m <br />m <br />a <br />v <br />JOB <br />NO: <br />23-06104 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.2 <br />