Laserfiche WebLink
REFLECTED GEILINC� PLAN <br />SCALE: 1/8" = 1'-0" <br />REFLECTED CEILIN4 PLAN LINREFERENCED NOTES <br />I. ALL GYPSUM BOARD CEILINGS AND SOFFITS ARE TO BE <br />TAPED, BEDDED AND SANDED TO RECEIVE TENANT FINISH. <br />2. DO NOT SCALE DRAWINGS. WRITTEN DIMENSIONS SHALL <br />GOVERN. LARGE SCALE DRAWINGS SHALL GOVERN OVER <br />SMALLER SCALE DRAWINGS. INFORM ARCHITECT OF ALL <br />DISCREPANCIES PRIOR TO CONSTRUCTION. <br />3. ALL DIMENSIONS ARE FROM FACE OF FINISH / GYP. <br />BOARD FINISH TO FACE OF FINISH / GYP. BOARD FINISH <br />AND / OR FROM FINISHED FLOOR TO FACE OF FINISH / <br />GYP. BOARD -CEILING FINISH UNLESS OTHERWISE NOTED. <br />4. CONTRACTOR TO PATCH AND REPAIR ALL DAMAGED <br />AREAS OF EXISTING GYP. BD. CEILINGS. <br />5. EXISTING LIGHTING SHOWN FOR REFERENCE ONLY. <br />CONTRACTOR TO VERIFY EXISTING CONDITIONS PRIOR TO <br />CONSTRUCTION. <br />6. THE REFLECTED CEILING PLAN IS INTENDED TO SHOW THE <br />EXTENT OF CEILING MATERIALS, SUCH AS LAY -IN TILE OR <br />GYPSUM BOARD, AND THE LOCATION OF SPECIFIED LIGHT <br />FIXTURES ONLY. REFERENCE MECHANICAL AND ELECTRICAL <br />ENGINEERING CONSTRUCTION DOCUMENTS FOR ALL OTHER <br />REQUIREMENTS. <br />REFLECTED CEILINC4 PLAN LEGEND <br />7. ALL MATERIALS LOCATED ABOVE THE CEILING GRID TO NEW 2X2 ACOUSTICAL LAY -IN CEILING TILE <br />BE NON-COMBUSTIBLE. NO LOOSE OR UNFACED INSULATION AND GRID <br />IN THE RETURN AIR PLENUM. <br />8. LOW VOLTAGE WIRING ABOVE THE CEILING SHALL BE NEW 2X4 LIGHT FIXTURES <br />INDEPENDENTLY SUPPORTED FROM STRUCTURE. <br />9. SUSPENDED ACOUSTICAL CEILING SYSTEMS SHALL BE NEW 2X2 LIGHT FIXTURES <br />INSTALLED IN ACCORDANCE WITH THE PROVISIONS OF <br />ASTM C 635 AND ASTM C 636. <br />HANGER CEILING WIRES TO BE 12 GA MIN. AT 4'-0" O.C. 0 NEW RECESSED CAN LIGHT FIXTURES <br />MAX. ATTACH HILTI XCW U22 (OR EQUAL) W/ CEILING WIRE <br />TO UNDERSIDE OF ROOF DECK. <br />ATTACH WALL ANGLE MOLDING TO GYP. BOARD WALL WITH NEW COVE LIGHTING <br />1-1/4" SCREW AT 16" O.C. MAX. <br />10. ALL LIGHTS SHALL BE SUPPORTED WITH U12 GA WIRE EXISTING EXIT LIGHT FIXTURE TO REMAIN <br />FROM BUILDING STRUCTURE AND NOT FROM CEILING GRID <br />OR OTHER NON-STRUCTURAL ITEMS. SECURE A MINIMUM OF <br />2 CORNERS (OPPOSITES) TO STRUCTURE ABOVE WITH EXISTING WALL MOUNTED EMERGENCY <br />CHAIN OR WIRE AND FASTEN TO CEILING GRID PER NEC LIGHT FIXTURE TO REMAIN <br />410.36. <br />ElNEW 2X2 EMERGENCY LIGHT FIXTURE WITH <br />BATTERY BACK-UP <br />NEW 2X4 EMERGENCY LIGHT FIXTURE WITH <br />BATTERY BACK-UP <br />0 NEW RECESSED CAN EMERGENCY LIGHT <br />FIXTURE WITH BATTERY BACK-UP <br />NEIGH CEILING HEIGHT INDICATION FROM FINISHED <br />FLOOR <br />REFLECTED CEILIMC PLAN C4ENERAL NOTES <br />I. ALL LIGHTS THROUGHOUT SPACE TO BE REPLACED. <br />2. EXISTING 2X4 CEILING TILE/GRID TO BE SALVAGED AND <br />CONVERTED TO A 2X2 GRID. REPAIR AND REPLACE <br />TILE/GRID AS NEEDED. <br />REFLECTED CEILINC4 PLAN REFERENCED NOTES <br />❑1 TIE NEW CEILING GRID INTO EXISTING TO MAKE <br />CONTINUOUS GRID AT 9'-0" <br />NEW COVE LIGHTING THROUGHOUT SOFFIT. SAME <br />LOCATION AS EXISTING COVE LIGHTING. <br />FARMER <br />ARCH ITECTU .Daniel H. Farmer, AJA <br />License <br />.1 Lees Baldwin Lan <br />Orlando, FL 32814 <br />321,441.3320 <br />JUL 3 11 202 <br />D,,i uei H arrfie!-.,. Ay,. 3 _11151 ¥i_3 <br />0 <br />J LO <br />z <br />O <br />Lo <br />0 <br />p <br />_ <br />F_ <br />n <br />0 <br />Q <br />- <br />Q <br />O0 <br />w <br />LL <br />J <br />~ <br />J <br />Q <br />Q <br />Z <br />J_ <br />0� <br />m: <br />O <br />= <br />0 <br />U <br />flIf <br />>- <br />C'f0 <br />< <br />Ir- <br />_ <br />a <br />F_ <br />zJ <br />Ir- <br />o <br />W <br />mot- <br />N <br />REVISIONS <br />