Laserfiche WebLink
- — - <br />12 <br />5 <br />FIBERGLASS SHINGLE INSTALLED AS PER <br />MANUFACTURER SPECIFICATIONS <br />T.O.P. <br />HDR. HGT. <br />EXTERIOR PLASTER 1 DECO FLASHING <br />ON FRAME 1/2 33 SH SHUTTER <br />DETAIL <br />�� \ 12 <br />12 <br />5� <br />TEXTURED -0 0 <br />CEMENTITIOUS <br />FINISH ON CM <br />SCORED STUCCO <br />BANDS <br />Fal Fol <br />�5 <br />25 SH ��� �� 25SH <br />_ --- — — --- <br />2NDFIN. FLR. <br />-- <br />---------- -- — <br />T.O.M. <br />___ <br />T.O.M. @GAR <br />CJ / WEEP <br />/ ENTRY <br />HDR. HGT. <br />SCORED <br />M r=1 r7l r7l��7� <br />Ind <br />1 l� <br />STUCCO BANDS <br />v <br />u <br />E-1 <br />El <br />El <br />El <br />El <br />El <br />111 <br />iio <br />� <br />El E:1 F-1 El L] El El <br />16070 OVERHEAD DOOR <br />FRONT ELEVATION — A <br />SCALE: 1/4" = V-0" <br />FIBERGLASS SHINGLE INSTALLED AS PER <br />MANUFACTURER SPECIFICATIONS <br />SCORED <br />STUCCO <br />BANDS <br />ri <br />SILL DETAIL <br />SCALE: 3/4" = V-0" <br />SCORED <br />STUCCO <br />BANDS <br />HEAD DETAIL <br />SCALE: 3/4" = V-0" <br />SCORED <br />STUCCf <br />BANDS <br />t. 1'-6" L. <br />DECO SHUTTER <br />SCALE: 3/4" = V-0" <br />---- <br />HDR_ <br />EXTERIOR <br />PLASTER ON CJ CJ <br />FRAME <br />25 SH <br />- — — — — — <br />— — — — — — — — — — — — — <br />--------- <br />FLASHING � <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON CMU <br />--—— --T--- <br />F, <br />CJ / WEEP <br />------------------------------ <br />25 SH <br />35 SH <br />------ ----- 1 _2ND F <br />_ —T.O.M <br />------------------- <br />---- ------------------ <br />_T.00.M <br />/ ENTF <br />_HDR_ <br />SCORED STUCCO <br />BANDS <br />LEFT ELEVATION — A <br />SCALE: 1/4" = V-0" <br />_FIN. FI <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4%1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />00 <br />N o <br />� W <br />O o w o <br />V aR O <br />C /9 fJ N <br />-c <br />y O t4 <br />�d <br />•d <br />��e <br />� 3 � <br />i <br />� c o <br />7 a' ' T <br />y E <br />Cc <br />a� <br />O\N <br />R O F•E S' <br />•" f�`l;�,rf1ltlttlllt",�.�\ <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineers signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal. <br />fA <br />W <br />F O M 3 <br />a <br />R N Na S <br />0 a,D $ �2 n <br />N in C, <br />N <br />'7 <br />Q C J LL W <br />Cc u_lL I d <br />J <br />Z_ z'0o <br />W $'�N(p <br />00 <br />W Wo 2 OR <br />ILZ�M <br />Z N OU ofv <br />W ❑ El <br />0 <br />Z N <br />Z § �18 <br />z o <br />v <br />z <br />CZ <br />�-J <br />0 s <br />�N <br />W <br />� a <br />V <br />0 w g <br />V J Ly N <br />U <br />r— E <br />i W t $ <br />I <br />= d <br />U °� <br />Q 00 0 <br />m <br />• <br />S� <br />�w <br />Mz <br />o <br />Z <br />14�_ <br />C6_ E <br />a <br />�o <br />p0 <br />>p <br />QN <br />=_® <br />°a <br />O <br />x° <br />�¢ <br />z <br />_° <br />°a <br />Z <br />N <br />W <br />W z <br />� � <br />•..-.. f�6 <br />C <br />¢zz p <br />OY <br />m p <br />°Z <br />Z <br />in <br />>Z <br /><Z <br />d <br /><ti <br />0 <br />Z <br />go <br />a 3 <br />LL <br />0. <br />W <br />o� <br />a � <br />o <br />w= <br />w <br />�o <br />mill� <br />f0 <br />� <br />z °d <br />d r <br />°° 3 <br />0 <br />c 0 <br />> M <br />0 <br />rn <br />m <br />C9 <br />L <br />00 <br />co A <br />_ <br />0 <br />f� <br />37 <br />V Y — <br />O <br />U) m � <br />N <br />C <br />L0 <br />ate-+ <br />CD N <br />O <br />N <br />00 0 <br />00 04 <br />U <br />Q <br />to `O <br />T <br />a� <br />m <br />M \ <br />co v; 00 <br />c <br />Z <br />Z <br />:3 <br />E T <br />E <br />c <br />0 <br />U Q p <br />_J <br />JOB <br />NO: 22-09406 <br />SCALE : AS NOTED <br />SHEET NO. <br />2.1 <br />