|
Wi .ICI i ,i ,. I JL IIL 1 ; L'LIllI&iA IL 1.: 1:1J
<br />Of NER.At MECHANICAL NOTES I OUfD00R 141R CALCULATIONS
<br />RVAC LOAD CALCULATION
<br />ISSUED FOR: REVIEW
<br />11.01.2021
<br />MECHANICAL NOTES:
<br />2020 F.M.C. SECTION 403.3.1.1
<br />IN GENERAL, PLANS AND DIAGRAMS ARE SCHEMATIC ONLY AND SHOULD NOT BE SCALED.
<br />ALL WALL MOUNTED THERMOSTATS AND/OR TEMPERATURE SENSORS SHALL BE INSTALLED AT AN ELEVATION OF 48" ABOVE FINISHED
<br />TENANT SPACE HAS:
<br />FLOOR TO THE TOP UNLESS OTHERWISE NOTED ON DRAWINGS. LOCATION OF THE WALL MOUNTED THERMOSTAT SHALL BE COORDINATED
<br />639 SQ. FT. OF SALES
<br />WITH OTHER TRADES FOR A NEAT APPEARANCE. FINAL LOCATION OF THERMOSTAT SHALL BE SUBJECT TO THE APPROVAL OF THE
<br />304 SQ. FT. OF STORAGE ROOM
<br />ENGINEER OR HIS REPRESENTATIVE IN THE FIELD.
<br />45 SQ. FT. OF TOILET ROOM
<br />ALL SUPPLY AIR DIFFUSERS SHALL BE 4-WAY THROW UNLESS OTHERWISE NOTED. CONTRACTOR SHALL PAINT INSIDE EACH RETURN
<br />GRILLE'S PLENUM AND DUCT CONNECTION FLAT BLACK TO CONCEAL CONNECTION. COORDINATE AIR DEVICE LOCATIONS WITH LIGHTING
<br />PER TABLE 403.3.1.1
<br />FIXTURES AND FIRE SPRINKLER HEADS. PRIOR TO INSTALLATION, THE CONTRACTOR IS TO REFER TO THE ARCHITECTURAL REFLECTED
<br />SALES OCCUPANT DENSITY IS (15 PERSON PER 1000 SQ. FT.)
<br />CEILING PLAN FOR ACTUAL FINAL LOCATIONS OF AIR DEVICES.
<br />STORAGE ROOM OCCUPANT DENSITY IS
<br />(0 PERSON PER 1000 SQ. FT.)
<br />CONTRACTOR SHALL PROVIDE A COPY OF THE TEST AND BALANCE REPORT BY AN AABC OR NEBB CERTIFIED AGENCY. ALL DUCTWORK
<br />TOILET ROOM OCCUPANT DENSITY IS (0
<br />PERSON PER 1000 SQ. FT.)
<br />MUST BE INSTALLED 6" AWAY FROM ANY FIRE RATED WALL TO FACILITATE INSPECTION.
<br />SALES CALCULATION
<br />THE GENERAL CONTRACTOR IS RESPONSIBLE FOR ALL TRADES INSTALLATION SCHEDULES. FIXED WORK SUCH AS DUCTWORK AND
<br />SQ. FT. = 639 15 x 639
<br />PLUMBING SHALL BE INSTALLED PRIOR TO ANY TRADE WORK THAT CAN BE EASILY RELOCATED OR OFFSET SUCH AS ELECTRICAL
<br />NUMBER OF OCCUPANT =------------- = 10 PERSON
<br />CONDUITS, SMALL WATER LINES ETC.
<br />1000
<br />PER EQUATION 4-1
<br />VbZ RpPz + RaAz
<br />PENETRATIONS THROUGH SMOKE OR FIRE -RATED ASSEMBLIES: PENETRATIONS FOR PIPES, CONDUITS OR OTHER PURPOSES THROUGH
<br />ASSEMBLIES (FLOORS, ROOF, WALLS, PARTITIONS, ETC.) WITH A REQUIRED FIRE RESISTANCE RATING SHALL BE SEALED TO THE
<br />Vbz = 7.5 X 10 + 0.12 X 639 = 152 CFM
<br />PENETRATING MEMBER IN AN APPROVED MANNER WHICH MAINTAINS THE REQUIRED FIRE RESISTANCE RATING OF THE ASSEMBLY AS
<br />Vbz
<br />FOLLOWS:
<br />PER EQUATION 4-2 SECTION 403.3.1.3
<br />V = ---
<br />WHERE HOLES FOR PENETRATIONS ARE FORMED CIRCULAR OR CORE -BORED, THE PENETRATION SHALL BE PROTECTED WITH
<br />°Z Ez
<br />FIRE -SEAL BRAND SMOKE AND FIRE STOP FITTINGS MFG. BY 0-Z GEDLEY, LINK SEAL BRAND BY THUNDER LINE OR AN EQUAL
<br />V0z = 152 / 0.8 = 190 CFM
<br />APPROVED BY ENGINEER.
<br />WHERE HOLES FOR PENETRATIONS ARE IRREGULAR (NON -CIRCULAR) IN SHAPE, THE PENETRATION SHALL BE PROTECTED WITH
<br />STORAGE ROOM CALCULATION
<br />DOW CORNING 3-6548, SILICONE RTV FOAM, 3M FIRE BARRIER PENETRATION SEAL SYSTEM OR AN EQUAL APPROVED BY THE
<br />SQ. FT. = 304
<br />ENGINEER.
<br />NUMBER OF OCCUPANT = -- 0 0--x 304- 304 =
<br />0 PERSON
<br />INTENT OF THESE NOTES AND MECHANICAL NOTES ON DRAWINGS IS TO CLARIFY THE SCOPE OF WORK AND ALERT CONTRACTOR OF
<br />1000
<br />EXISTING CONDITIONS. CONTRACTOR TO VISIT SITE AND VERIFY ALL CLEARANCES BEFORE FABRICATION OF DUCTWORK AND PROVIDE
<br />PER EQUATION 4-1
<br />VZ Rbp P + R A
<br />ADDITIONAL OFFSET AND/OR CHANGES IN DUCT SIZES TO MEET FIELD CONDITIONS AND COORDINATE WITH ELECTRICAL, PLUMBING AND
<br />z a z
<br />FIRE PROTECTION SUBCONTRACTOR BEFORE ANY CONSTRUCTION WORK.
<br />Vbz = 0 X 0 + 0.012 X 304 = 4 CFM
<br />FLEXIBLE AND RIGID ROUND DUCT TAKE -OFFS FOR DIFFUSERS SHALL BE THE SAME SIZE AS DIFFUSER NECK. MAXIMUM FLEXIBLE DUCT
<br />PER EQUATION 4-2 SECTION 403.3.1.3
<br />V =Vbz
<br />Oz
<br />LENGTH SHALL BE 8'- 0".
<br />Ez
<br />V°Z=0/0.8=5CFM
<br />UNLESS OTHERWISE NOTED, INSTALL DUCTWORK AS HIGH AS POSSIBLE, TIGHT TO BOTTOM OF STRUCTURE. COORDINATE DUCT ELEVATION
<br />WITH RAIN LEADERS, WATER PIPING, SANITARY DRAINS AND MAJOR ELECTRICAL CONDUITS.
<br />TOILET ROOM CALCULATION
<br />CONTRACTOR SHALL PROVIDE ALL SUPPLEMENTARY STEEL REQUIRED TO SUSPEND MECHANICAL EQUIPMENT AND MATERIALS. PROVIDE
<br />SQ. FT. = 45 0 x 45
<br />MANUAL OR AUTOMATIC DAMPERS IN ALL OUTSIDE AIR DUCTS.
<br />NUMBER OF OCCUPANT =------------- =
<br />1000
<br />0 PERSON
<br />PROVIDE A TRAP IN ALL CONDENSATE PIPING LOCATED AT THE AIR HANDLING UNIT. INSULATE ALL CONDENSATE LINES WITH 1/2" THICK
<br />PER EQUATION 4-1
<br />VbZ RpPz +RaAz
<br />CLOSED CELL FOAM INSULATION.
<br />Vbz=OXO+OX45 =OCFM
<br />PROVIDE A 4" HIGH CONCRETE HOUSEKEEPING PAD UNDER ALL MECHANICAL EQUIPMENT, UNLESS OTHERWISE NOTED. PADS SHALL BE 4"
<br />Vbz
<br />LARGER THAN THE EQUIPMENT ON ALL SIDES.
<br />PER EQUATION 4-2 SECTION 403.3.1.3
<br />VOZ ---
<br />Ez
<br />UNLESS OTHERWISE NOTED, ALL UNDERGROUND PIPING SHALL HAVE A MINIMUM OF 3'-0" OF COVER.
<br />V = 0 / 0.8 = 0 CFM
<br />ALL MECHANICAL WORK SHALL MEET ALL THE REQUIREMENTS OF THE "2007 FLORIDA MECHANICAL CODE" AND ALL UPDATED
<br />O2
<br />AMENDMENTS.
<br />TOTAL CFM REQUIRED FOR ALL AREAS =
<br />RECTANGULAR SUPPLY, RETURN, AND TRANSFER AIR DUCTS SHALL BE CONSTRUCTED OF 1.5" THICK DUCT BOARD AND CONFORM WITH UL
<br />190 + 5 = 195 CFM
<br />STANDARDS FOR SAFETY AIR DUCT, NO. 181, 1967 ESTABLISHED FOR CLASS 1 AIR DUCTS. CONSTRUCTION SHALL COMPLY WITH
<br />195 CFM OF OUTSIDE AIR IS REQUIRED
<br />RECOMMENDATIONS AND DETAILS IN SMACNA BULLETIN 15, LATEST REVISION AND MANUFACTURER'S RECOMMENDATIONS. ALL JOINTS
<br />200 CFM OF OUTSIDE AIR IS PROVIDED THRU RTU-1
<br />SHALL BE SECURELY TAPED WITH FASSON 0810 OR APPROVED EQUAL PRESSURE SENSITIVE TAPE. METAL TO FIBERGLASS CONNECTIONS
<br />TO BE MADE USING 3" WIDE GLASS FABRIC TAPE WITH FOSTER 30/35 MASTIC OR EQUAL. SUPPORT DUCTS WITH 1X2X1 22 GAUGE
<br />MINIMUM CHANNELS AND STRAP OR 12-GAUGE WIRE FROM BUILDING CONSTRUCTION. SUSPEND FROM JOISTS WITH BEAM CLAMPS. PROVIDE
<br />HOT DIPPED STEEL FASTENERS, ANCHORS, RODS, STRAPS, TRIM AND ANGLES FOR SUPPORT OF DUCTWORK.
<br />PROVIDE ADDITIONAL DUCTWORK AND PIPING SUPPORTS ON BOTH SIDES AND WITHIN 18" OF FIRE RATED WALL. DUCTWORK OR PIPING
<br />SHALL NOT BE SUPPORTED FROM ANY FIRE RATED WALL.
<br />TURNING VANES SHALL BE PROVIDED IN ALL SUPPLY DUCT RECTANGULAR ELBOWS WITH ANGLES BETWEEN 45 DEGREES AND LESS THAN
<br />90 DEGREES PER FIG. 2-5 OF THE SMACNA MANUAL.
<br />DUCT DIMENSIONS SHOWN ON DRAWINGS ARE CLEAR INSIDE DIMENSIONS.
<br />MECHANICAL CONTRACTOR SHALL SIZE AND INSTALL REFRIGERANT PIPING PER MANUFACTURER'S RECOMMENDATIONS. REFRIGERANT PIPING
<br />SHALL BE TYPE "K" COPPER WITH BRAZED JOINTS. APPLY 3'4" CLOSED CELL INSULATION ON COMPRESSOR SUCTION LINE.
<br />DUCTWORK, DIFFUSERS, REGISTERS, GRILLES, AND OTHER ITEMS OF THE AIR HANDLING SYSTEM SHALL NOT BE SUPPORTED BY THE
<br />CEILING OR CEILING SUSPENSION SYSTEM.
<br />O ROOF TOP UNI JI/i� M W0. KA! � FUC. CWU
<br />NOTE: ALL DUCT WRAP SHALL BE SEALED WITH GLASS
<br />FAB AND MASTIC.
<br />NET HEATING
<br />ENTERING COOLING CAPACITY ELECTRICAL
<br />MARK MFG/MODEL DISCHARGE TONS ESP CFM OUTSIDE AIR CAPACITY EER KW CRATED MCA/ UNIT WEIGHT
<br />SPIN -IN FITTING
<br />WITH VOLUME
<br />WRAPPED
<br />SHEETMETAL
<br />AIR CFM CONDITIONS (MBH) VOLTAGE VOLT / PH / Hi MOCP (LBS)
<br />EXTRACTOR AND
<br />\ DUCT SEE NOTE
<br />RTU-1 CARRIER SOHCA04 DOWNFLOW 3 1.0 1200 200 80°F DB 67°F WB 36 12.5 8.7 @ 208 208 / 3 / 60 33/35 458
<br />BALANCING
<br />#6 IN GENERAL
<br />OR EQ. 0 95 OF AMBIENTI
<br />DAMPER
<br />HAVC. SPECS.
<br />HARD DUCT
<br />ACCESSORIES PROVIDED AND INSTALLED BY TENANT CONTRACTOR:
<br />HORIZONTAL
<br />1. NEW ROOF CURB, CARRIERITHYBAR TC-05 14 GAUGE CURB CERTIFIED FOR LOCAL WIND LOAD (175 MPH) AND ATTACHMENT KIT WITH UNIT/PANEL WIND KIT.
<br />2. DRAIN PAN OVERFLOW SWITCH FOR UNIT SHUT DOWN.
<br />HARD ELBOWS
<br />ACCESSORIES PROVIDED BY TENANT FOR TENANT CONTRACTOR INSTALLATION:
<br />WHERE BEND
<br />DUCT CLAMP
<br />1. DIFFERENTIAL ENTHALPY ECONOMIZER WITH BAROMETRIC RELIEF.
<br />EXCEEDS 450
<br />2. INSTALL EMS CONTROLS PACKAGE.
<br />3. LOUVERED CONDENSER COIL GUARDS.
<br />DUCT
<br />INSULATED FLEXIBLE
<br />4. UNIT MOUNTED NON POWERED WEATHERPROOF GFCI OUTLET.
<br />CLAMP
<br />DUCT
<br />5. UNIT MOUNTED DISCONNECT SWITCH.
<br />/
<br />1-1/2" INSULATION WITH
<br />(VOTE:
<br />VAPOR BARRIER COVERING
<br />CONTRACTOR SHALL BE RESPONSIBLE FOR ALL STARTUP AND WARRANTY WORK. VERIFY ELECTRICAL POWER PRIOR TO
<br />TOP SIDE OF DIFFUSER
<br />INSTALLING UNITS. FAILURE TO DO SO SHALL RESULT IN CONTRACTOR FURNISHING CORRECT UNITS OR POWER AT NO
<br />FROM NECK TO CEILING
<br />AND SEALED TO DUCT
<br />ADDITIONAL COST TO TENANT.
<br />INSULATION. (R=6.0)
<br />G UMOOM WATUST FIN SCNEM
<br />FLEX DUCT INSTL. PETAIL
<br />MARK MANUFACTURER MODEL # TYPE CFM E.S.P. WATTS VOLTS/pf B.D.D. DRIVE REMARKS
<br />SCALE: NONE
<br />EF-1 GREENHECK SP-C CEILING 50 0.125 46 115/1 NO DIRECT 1,2
<br />1. PROVIDE WITH FACTORY SPEED CONTROLLER FOR BALANCING, AND FACTORY DISCONNECT.
<br />MECHANICAL LEGEND
<br />2. INTERLOCK WITH LIGHT SWITCH.
<br />SYMBOL
<br />DE'SCRIP
<br />AIR Ii��cc .1�/i SV�I pper�'� U
<br />NEW DUCTWORK, PIPING, OR EQUIPMENT
<br />MARK TYPE MATERIAL FINISH ACCESSORIES MANUFACTURER REMARKS
<br />AND MODEL
<br />EXISTING DUCTWORK, PIPING, OR EQUIPMENT TO REMAIN
<br />MOUNTED ALUMINUM ALUMINUM ASD TITUS
<br />SUPPLY OR OUTSIDE AIR DUCT SECTION
<br />ODUCT
<br />B SUPPLY S300FL X X 26 ASD
<br />DIFFUSER OR EQUAL
<br />RETURN OR EXHAUST DUCT SECTION
<br />SUPPLY ALUMINUM BAK. WHT. O OBD TfmS
<br />PAS 1 & 2
<br />DIFFUSER ENAMEL
<br />12X12
<br />DUCTWORK TRANSITION
<br />RETURN BAK. WHT. OBD TITUS
<br />D REGISTER ALUMINUM ENAMEL PAR 1
<br />MANUAL AIR VOLUME CONTROL DAMPER
<br />24X24
<br />AIR DEVICE NOTES: 1. CONTRACTOR TO COORDINATE AIR DEVICE FRAMES WITH CEILING AND/OR WALL TYPE.
<br />® m
<br />SUPPLY AIR DEVICE. CLEAR TRIANGLE SIDES INDICATE
<br />2. NECK SIZES AND CFM QUANTITIES SHOWN ON MECHANICAL FLOOR PLANS.
<br />AIR FLOW PATTERN
<br />z
<br />RETURN OR EXHAUST AIR DEVICE
<br />OUTSIDE AIR INTAKE ROOF CAP
<br />NEW CONNECTION TO EXISTING EQUIPMENT
<br />_-
<br />UNDERCUT DOOR 3/4" (MINIMUM)
<br />Q
<br />WALL MOUNTED THERMOSTAT
<br />SMOKE DETECTOR
<br />CD
<br />CEILING DIFFUSER
<br />RRC
<br />RETURN REGISTER AT CEILING
<br />BASIS OF DESIGN:
<br />SUMMER
<br />WINTER
<br />HEATING LOAD:
<br />OUTSIDE AIR
<br />ROOF
<br />GLASS
<br />WALLS
<br />COOLING LOAD:
<br />SENSIBLE LOAD:
<br />OUTSIDE AIR
<br />ROOF
<br />GLASS
<br />WALLS
<br />PEOPLE
<br />LIGHTING
<br />> ;Al2►i11[97_1f
<br />OUTSIDE
<br />PEOPLE
<br />OUTSIDE
<br />917 db, 777 wb
<br />40'F db
<br />INSIDE
<br />75-F db, 50% R.H.
<br />70'F Fdb
<br />200 CFM X 30' X
<br />1.08
<br />= 6480.00
<br />BTUH
<br />1010 SQ.FT. X 30' X
<br />0.031
<br />= 939.30
<br />BTUH
<br />148 SQ.FT. X 30' X
<br />1.16
<br />= 5150.40
<br />BTUH
<br />503 SQ.FT. X 30' X
<br />0.36
<br />= 5432.40
<br />BTUH
<br />TOTAL SPACE HEAT LOAD .... = 18002.10 BTUH
<br />200 CFM X 16' X
<br />1.08
<br />= 3456.00
<br />BTUH
<br />1010 SQ.FT. X
<br />16' X
<br />0.031
<br />= 500.96
<br />BTUH
<br />148 SQ.FT. X
<br />16' X
<br />1.16
<br />= 2746.88
<br />BTUH
<br />503 SQ.FT. X
<br />16' X
<br />0.36
<br />= 2897.28
<br />BTUH
<br />10 PEOPLE X
<br />250
<br />= 2500.00
<br />BTUH
<br />330 WATT X
<br />3.412
<br />= 1125.96
<br />BTUH
<br />SENSIBLE TOTAL ..................=
<br />13227.08
<br />BTUH
<br />200 CFM X 0.68 X 54 = 7344.00 BTUH
<br />10 PEOPLE X 250 = 2500.00 BTUH
<br />LATENT TOTAL .....................= 9844.00 BTUH
<br />GRAND TOTAL COOLING LOAD = 23071.08 BTUH
<br />2 TONS REQUIRED
<br />3 TONS PROVIDED
<br />glll � NEW UNIT
<br />GASKET
<br />NEW UNIT BASE
<br />RAIL
<br />EXIST.MANUFACTURED ,�1/4" x #28 x 6" TEK
<br />ROOF CURB HEX STEEL -ZINC
<br />P.T. NAILER FASTENER -ALL FOUR
<br />HARD INSULATION __ SIDES 16"
<br />MAXIMUU M SPACING
<br />CANT. G.C. VERIFY.
<br />EXIST. ROOFING TOP
<br />EXIST. 3/8" MIN THREADED ROD CAP & INSULATION.6.C. VERIFY
<br />WITH -IN 12" EA. CORNER THROUGH
<br />CURB STEEL AND BUILDING ----�--�---�-- -----------�--------
<br />STRUCTURE. G.C. VERIFY
<br />EXIST. WELDED STEEL L4X4
<br />EQUIPMENT FRAME BELOW oo" L
<br />DECK & RTU CURB STEEL TYPICAL METAL
<br />DECK PAN ROOF
<br />SUPPORT
<br />EXIST. 2"x2"4/4" STIFFENER -� STRUCTURAL
<br />MIN. @ EACH LOCATION OF L4X4
<br />STEEL ANGLE AT CROSSING STEEL JOIST
<br />POINT OF EXIST.ROOF TRUSSES.
<br />G.C. VERIFY
<br />EQUIPMENT ATTACHMENT TO EXIST
<br />ROOF CURB HOLD DOWN N.T.S.
<br />V I I MAX. 200
<br />TRANSITION
<br />0.25 D (4" MIN. PER SMACNA)
<br />RECTANGULAR DUCT
<br />o
<br />to 0
<br />N
<br />VOLUME DAMPER
<br />CONICAL FITTING WITH
<br />LOCKING TYPE VOLUME
<br />DAMPER. OR SIDE WALL
<br />TAKEOFF EQUAL TO
<br />FLEXMASTER STO.
<br />`FLEX DUCT OR ROUND
<br />SHEET METAL DUCT.
<br />FLEX DUCT MAX. 5'-0"
<br />Ld LONG, USE CLAMP TO
<br />ATTACH FLEX DUCTS
<br />AND SEAL. SUPPORT
<br />DUCT EVERY FOUR
<br />FEET FROM
<br />STRUCTURE
<br />6IA140H DUCT DETAILS
<br />NO SCALE
<br />EXI
<br />50 CFM 50 CFM
<br />O O
<br />00
<br />50 CFM 50 CFM
<br />CB)
<br />OB
<br />1000 CFM R/A 0
<br />1OX20 UP TO RTU-1 0
<br />O
<br />g3 1000
<br />CFM
<br />T R/A
<br />0 to
<br />�=
<br />CFM G
<br />RTU-1 XH'
<br />50
<br />0 CFM
<br />io
<br />100 CFM 100 CFM
<br />100 CFM 100 CFM
<br />100 C� 100 CFM
<br />O O
<br />O
<br />150 CF� 150 CFM
<br />O O
<br />EXIT
<br />0
<br />MECHANICAL PLAN
<br />SCALE: 1/4" = V-0"
<br />1200 CFM 16X12
<br />SUPPLY DUCT
<br />DOWN FROM RTU-1
<br />MECHANICAL PLAN NOTES
<br />OPROVIDE AND INSTALL RTU PER SCHEDULE & DETAIL.
<br />O2 PROVIDE & INSTALL FLEXIBLE DUCT DOWN TO SUPPLY DIFFUSER.
<br />O3 PROVIDE AND INSTALL ZONE SENSOR THERMOSTAT, COORDINATE
<br />LOCATION WITH OWNER
<br />OPROVIDE AND INSTALL RESTROOM EXHAUST FAN PER SCHEDULE. RUN 5"
<br />EXHAUST DUCT TO ROOF AND INSTALL ROOF CAP. 10'-0" MINIMUM
<br />SEPARATION IS REQUIRED BETWEEN EXHAUST OUTLET AND AIR -INTAKES
<br />BEFORE PERMITTING OR START OF CONSTRUCTION:
<br />1. TENANT TO ACQUIRE LANDLORD WRITTEN APPROVAL OF ALL PROPOSED ALTERATIONS.
<br />2. CONTRACTOR TO VERIFY ALL EXISTING DIMENSIONS AND ELEVATIONS.
<br />3. CONTRACTOR TO COORDINATE ROUGH WINDOW/ DOOR OPENINGS SIZE W/ MFR SPEC:
<br />Z
<br />F
<br />a
<br />Fr
<br />U
<br />In
<br />W
<br />0
<br />�D
<br />"t
<br />O
<br />0
<br />Q
<br />co
<br />co
<br />O
<br />w
<br />x
<br />a
<br />z
<br />Q
<br />x
<br />U
<br />O
<br />w
<br />Z
<br />Ia
<br />U
<br />w
<br />W
<br />O
<br />m
<br />�
<br />a
<br />�
<br />W
<br />Z
<br />F
<br />Lo
<br />>
<br />. __j
<br />0)
<br />Lo
<br />U
<br />U
<br />Z
<br />a
<br />IL
<br />t3i
<br />�O
<br />� U
<br />co
<br />H
<br />co
<br />I
<br />r-o
<br />�jE
<br />O
<br />w
<br />;T-1
<br />z
<br />W
<br />H
<br />W
<br />r-
<br />co
<br />co
<br />F�
<br />Gj
<br />T�
<br />H
<br />rn
<br />V 1
<br />(u
<br />a
<br />O
<br />E-
<br />a;
<br />P.
<br />m�
<br />O 8�
<br />a
<br />O
<br />Cq
<br />a
<br />CID
<br />JOB. N0. 21040
<br />G�`I
<br />\v
<br />� COA. N0.29116
<br />MAZEN MARIE, PE.
<br />L. E # 60166)
<br />_ �c
<br />'�,il11111\\
<br />M1.0
<br />
|