|
EGRESS:
<br />MINIMUM SIZE.
<br />EMERGENCY ESCAPE AND RESCUE OPENINGS SHALL HAVE A
<br />, MINIMUM NET CLEAR OPENING OF 5.7 SQUARE FEET.
<br />EXCEPTION:
<br />1. ALL GRADE FLOOR OPENINGS SHALL HAVE A MINIMUM NET
<br />CLEAR OPENING OF 5 SQ FT.
<br />MAXIMUM HEIGHT FROM FLOOR:
<br />EMERGENCY ESCAPE AND RESCUE OPENINGS SHALL HAVE THE
<br />BOTTOM OF THE CLEAR OPENING NOT GREATER THAN 44 INCHES
<br />MEASURED FROM THE FLOOR.
<br />2. OPERATIONAL CONSTRAINTS:
<br />EMERGENCY ESCAPE AND RESCUE OPENINGS SHALL BE
<br />OPERATIONAL FROM THE INSIDE OF THE ROOM WITHOUT THE USE
<br />OF KEYS OR TOOLS. BARS, GRILLES, GRATES OR SIMILAR DEVICES
<br />ARE PERMITTED TO BE PLACED OVER EMERGENCY ESCAPE AND
<br />RESCUE OPENINGS PROVIDED THE MINIMUM NET CLEAR OPENING
<br />SIZE COMPLIES WITH SECTION 1030.4 AND SUCH DEVICES SHALL
<br />BE RELEASABLE OR REMOVABLE FROM THE INSIDE WITHOUT THE
<br />USE OF A KEY, TOOL OR FORCE GREATER THAN THAT WHICH IS
<br />REQUIRED FOR NORMAL OPERATION OF THE ESCAPE AND RESCUE
<br />OPENING.
<br />3. FALL PROTECTION:
<br />WHERE THE OPENING OF THE SILL PORTION OF AN OPERABLE
<br />WINDOW IS LOCATED MORE THAN 72 INCHES (1829 MM) ABOVE
<br />THE FINISHED GRADE OR OTHER SURFACE BELOW, THE LOWEST
<br />PART OF THE CLEAR OPENING OF THE WINDOW SHALL BE AT A
<br />HEIGHT NOT LESS THAN 24 INCHES (610 MM) ABOVE THE FINISHED
<br />FLOOR SURFACE OF THE ROOM IN WHICH THE WINDOW IS
<br />LOCATED. GLAZING BETWEEN THE FLOOR AND A HEIGHT OF 24
<br />INCHES (610 MM) SHALL BE FIXED OR HAVE OPENINGS THROUGH
<br />WHICH A 4-INCH (102 MM) DIAMETER SPHERE CANNOT PASS.
<br />EXCEPTION: OPENINGS THAT ARE PROVIDED WITH WINDOW
<br />GUARDS THAT COMPLY WITH ASTM F 2006 OR F 2090.
<br />HAZARDOUS LOCATIONS:
<br />1. GLAZING IN DOORS: GLAZING IN ALL FIXED AND OPERABLE PANELS
<br />OF SWINGING, SLIDING, AND BIFOLD DOORS SHALL BE CONSIDERED A
<br />HAZARDOUS LOCATION.
<br />EXCEPTIONS:
<br />1. DECORATIVE GLAZING
<br />2. WHEN THERE IS AN INTERVENING WALL OR OTHER
<br />PERMANENT BARRIER BETWEEN THE DOOR AND THE
<br />GLAZING.
<br />3. GLAZING IN WALLS ON THE LATCH SIDE OF AND
<br />PERPENDICULAR TO THE PLANE OF THE DOOR IN A CLOSED
<br />POSITION.
<br />4. WHERE ACCESS THROUGH THE DOOR IS TO A CLOSET OR
<br />STORAGE AREA 3 FEET OR LESS IN DEPTH. GLAZING IN THIS
<br />APPLICATION SHALL COMPLY WITH SECTION R308.4.3.
<br />5. GLAZING THAT IS ADJACENT TO THE FIXED PANEL OF PATIO
<br />DOORS.
<br />' 2. GLAZING IN WINDOWS:
<br />GLAZING IN AN INDIVIDUAL FIXED OR OPERABLE PANEL THAT MEETS
<br />ALL OF THE FOLLOWING CONDITIONS:
<br />1. EXPOSED AREA OF AN INDIVIDUAL PANE GREATER THAN 9
<br />SQUARE FEET.
<br />2. BOTTOM EDGE LESS THAN 18 INCHES ABOVE THE FLOOR.
<br />3. TOP EDGE GREATER THAN 36 INCHES ABOVE THE FLOOR.
<br />4. ONE OR MORE WALKING SURFACES WITHIN 36 INCHES (914
<br />MM) HORIZONTALLY OF THE GLAZING.
<br />3. GLAZING AND WET SURFACES:
<br />GLAZING IN WALLS, ENCLOSURES OR FENCES CONTAINING OR FACING
<br />SWIMMING POOLS, HOT TUBS AND SPAS WHERE THE BOTTOM EDGE OF THE
<br />GLAZING IS LESS THAN 60 INCHES MEASURED VERTICALLY ABOVE ANY
<br />WALKING SURFACE SHALL BE CONSIDERED A HAZARDOUS LOCATION. THIS
<br />SHALL APPLY TO SINGLE GLAZING AND ALL PANES IN MULTIPLE GLAZING.
<br />EXCEPTION: GLAZING THAT IS MORE THAN 60" (1,524 mm), MEASURED
<br />HORIZONTALLY AND IN A STRAIGHT LINE, FROM THE WATER'S EDGE OF A
<br />BATHTUB, HOT TUB, SPA, WHIRLPOOL, OR SWIMMING POOL OR FROM THE
<br />EDGE OF A SHOWER, SAUNA, OR STEAM ROOM.
<br />4. GLAZING ADJACENT TO THE BOTTOM OF A STAIR LANDING:
<br />GLAZING ADJACENT TO THE LANDING AT THE BOTTOM OF A STAIRWAY
<br />WHERE THE GLAZING IS LESS THAN 36" ABOVE THE LANDING AND WITHIN 60"
<br />HORIZONTALLY OF THE BOTTOM TREAD SHALL BE CONSIDERED A
<br />HAZARDOUS LOCATION.
<br />R309.1 FLOOR SURFACE:
<br />GARAGE FLOOR SURFACES SHALL BE OF APPROVED NONCOMBUSTIBLE
<br />MATERIAL.
<br />THE AREA OF FLOOR USED FOR PARKING OF AUTOMOBILES OR OTHER
<br />VEHICLES SHALL BE SLOPED TO FACILITATE THE MOVEMENT OF LIQUIDS
<br />TO A DRAIN OR TOWARD THE MAIN VEHICLE ENTRY DOORWAY.
<br />R302.9 FLAME SPREAD INDEX AND SMOKE -DEVELOPED INDEX FOR WALL
<br />AND CEILING FINISHES
<br />FLAME SPREAD AND SMOKE DEVELOPED INDEXES FOR WALL AND
<br />CEILING FINISHES SHALL BE IN ACCORDANCE WITH SECTIONS R302.9.1
<br />THROUGH R302.9.4.
<br />R302.10 FLAME SPREAD INDEX AND SMOKE -DEVELOPED INDEX FOR
<br />INSULATION
<br />FLAME SPREAD AND SMOKE -DEVELOPED INDEX FOR INSULATION SHALL
<br />BE IN ACCORDANCE WITH SECTIONS R302.10.1 THROUGH R302.10.5.
<br />ITP
<br />GENERAL CONSTRUCTION NOTES:
<br />TREADS AND RISERS:
<br />THE MAXIMUM RISER HEIGHT SHALL BE 7.75" AND THE MINIMUM
<br />TREAD DEPTH SHALL BE 10". THE TREAD DEPTH SHALL BE
<br />MEASURED HORIZONTALLY BETWEEN THE VERTICAL PLANES OF
<br />THE FOREMOST PROJECTION OF THE ADJACENT TREADS AND AT A
<br />RIGHT ANGLE TO THE TREADS LEADING EDGE. THE MINIMUM
<br />WINDER TREAD DEPTH AT THE WALK LINE SHALL BE 10", AND THE
<br />MINIMUM WINDER TREAD DEPTH SHALL BE 6". NOSING SHALL
<br />NOT BE LESS THAN 3/4" BUT NOT MORE THAN 1 1/4". A NOSING
<br />SHALL NOT BE REQUIRED WHERE THE TREAD DEPTH IS 11".
<br />HANDRAILS:
<br />HANDRAILS SHALL BE PROVIDED ON AT LEAST ONE SIDE OF EACH
<br />CONTINUOUS RUN OF TREADS OR FLIGHTS OF 4 OR MORE RISERS.
<br />HANDRAIL HEIGHT:
<br />HANDRAIL HEIGHT, MEASURED ABOVE STAIR TREAD NOSINGS, OR
<br />FINISH SURFACE OF RAMP SLOPE SHALL BE UNIFORM, NOT LESS
<br />THAN 34" AND NOT MORE THAN 38".
<br />HANDRAIL GRASPABILITY:
<br />HANDRAILS WITH A CIRCULAR CROSS-SECTION SHALL HAVE AN
<br />OUTSIDE DIAMETER OF AT LEAST 1.25" AND NOT GREATER THAN
<br />2" OR SHALL PROVIDE EQUIVALENT GRASPABILITY. IF THE
<br />HANDRAIL IS NOT CIRCULAR, IT SHALL HAVE A PERIMETER
<br />DIMENSION OF AT LEAST 4" AND NOT GREATER THAN 6.25" WITH A
<br />MAXIMUM CROSS-SECTION DIMENSION OF 2.25". EDGES SHALL
<br />HAVE A MINIMUM RADIUS OF 0.01".
<br />HANDRAIL CONTINUITY:
<br />HANDRAIL -GRIPPING SURFACES SHALL BE CONTINUOUS,
<br />WITHOUT INTERRUPTION BY NEWEL POSTS OR OTHER
<br />OBSTRUCTIONS.
<br />EXCEPTIONS:
<br />LHANDRAILS WITHIN DWELLING UNITS ARE PERMITTED TO
<br />BE INTERRUPTED BY A NEWEL POST AT A STAIR OR RAMP
<br />LANDING.
<br />2. WITHIN A DWELLING UNIT, THE USE OF A VOLUTE, TURNOUT
<br />OR STARTING EASING IS ALLOWED ON THE LOWEST TREAD.
<br />3. HANDRAIL BRACKETS OR BALUSTERS ATTACHED TO THE
<br />BOTTOM SURFACE OF THE HANDRAIL SHALL NOT BE
<br />CONSIDERED OBSTRUCTIONS TO GRASPABILITY, PROVIDED
<br />THAT THE FOLLOWING CONDITIONS ARE MET:
<br />3.1. THEY DO NOT PROJECT HORIZ BEYOND THE SIDES OF THE
<br />HANDRAIL WITHIN 1'/z" OF THE BOTTOM OF THE HANDRAIL
<br />AND PROVIDED THAT, FOR EACH 1/2" OF ADDITIONAL
<br />HANDRAIL PERIMETER DIMENSION ABOVE 4", THE VERTICAL
<br />CLEARANCE DIMENSION OF V/2" CAN BE REDUCED BY 1/8".
<br />3.2. THEY HAVE EDGES WITH A RADIUS OF NOT LESS THAN .01".
<br />3.3. THEY OBSTRUCT NOT IN EXCESS OF 20 PERCENT OF THE
<br />HANDRAIL LENGTH.
<br />HANDRAIL CLEARANCE:
<br />CLEAR SPACE BETWEEN A HANDRAIL AND A WALL OR OTHER
<br />SURFACE SHALL BE A MINIMUM OF 1.5". A HANDRAIL AND A WALL
<br />OR OTHER SURFACE ADJACENT TO THE HANDRAIL SHALL BE FREE
<br />OF ANY SHARP OR ABRASIVE ELEMENTS.
<br />GUARDS:
<br />SHALL BE LOCATED ALONG OPEN -SIDED WALKING SURFACES,
<br />PLATFORMS, STAIRWAYS, RAMPS AND LANDINGS THAT ARE
<br />LOCATED MORE THAN 30" MEASURED VERTICALLY TO THE FLOOR
<br />OR GRADE BELOW AT ANY POINT WITHIN 36" HORIZONTALLY TO
<br />THE EDGE OF THE OPEN SIDE. INSECT SCREENING SHALL NOT BE
<br />CONSIDERED AS A GUARD.
<br />OPENING LIMITATIONS:
<br />REQUIRED GUARDS SHALL NOT HAVE OPENINGS FROM THE
<br />WALKING SURFACE TO THE REQUIRED GUARD HEIGHT WHICH
<br />ALLOW THE PASSAGE OF A 4" SPHERE.
<br />SCREEN PORCHES:
<br />PORCHES AND DECKS WHICH ARE ENCLOSED WITH INSECT
<br />SCREENING SHALL BE PROVIDED WITH GUARDS WHERE THE
<br />WALKING SURFACE IS LOCATED MORE THAN 30" ABOVE THE
<br />FLOOR OR GRADE BELOW.
<br />FIRE PROTECTION:
<br />FIREBLOCKING SHALL BE PROVIDED TO CUT OFF ALL VERTICAL
<br />AND HORIZONTAL CONCEALED DRAFT OPENINGS.
<br />ASPHALT SHINGLES (IF APPLICABLE) :
<br />1. WIND RESISTANCE OF ASPHALT SHINGLES. - ASPHALT
<br />SHINGLES SHALL BE INSTALLED IN ACCORDANCE WITH
<br />SECTION R905.2.6 AND R905.2.6.1.
<br />R506.2.3 VAPOR RETARDER:
<br />A 6-MIL POLYETHYLENE OR APPROVED VAPOR RETARDER WITH
<br />JOINTS LAPPED NOT LESS THAN 6 INCHES (152 MM) SHALL BE
<br />PLACED BETWEEN THE CONCRETE FLOOR SLAB AND THE BASE
<br />COURSE OR THE PREPARED SUBGRADE WHERE NO BASE
<br />COURSE EXISTS.
<br />EXCEPTIONS
<br />1. GARAGES, UTILITY BUILDINGS AND OTHER UNHEATED
<br />ACCESSORY STRUCTURES.
<br />2. FOR UNHEATED STORAGE ROOMS HAVING AN AREA OF
<br />LESS THAN 70 SQUARE FEET (6.5 M2) AND CARPORTS.
<br />3. DRIVEWAYS, WALKS, PATIOS AND OTHER FLATWORK NOT
<br />LIKELY TO BE ENCLOSED AND HEATED AT A LATER DATE.
<br />4. WHERE APPROVED BY THE BUILDING OFFICIAL, BASED ON
<br />LOCAL SITE CONDITIONS.
<br />DRAFTSTOPPING:
<br />IN COMBUSTABLE CONSTRUCTION WHERE THERE IS USABLE
<br />SPACE BOTH ABOVE AND BELOW THE CONCEALED SPACE OF A
<br />FLOOR/CEILING ASSEMBLY, DRAFTSTOPS SHALL BE INSTALLED
<br />SO THAT THE AREA OF THE CONCEALED SPACE DOES NOT
<br />EXCEED 1,000 SQUARE FEET. DRAFTSOPPING SHALL DIVIDE THE
<br />THE CONCEALED SPACE INTO APPROXIMATELY EQUAL AREAS.
<br />WHERE THE ASSEMBLY IS ENCLOSED BY A FLOOR MEMBRANE
<br />ABOVE AND A CEILING MEMBRANE BELOW, DRAFTSTOPPING
<br />SHALL BE PROVIDED IN FLOOR/CEILING ASSEMBLIES UNDER THE
<br />FOLLOWING CIRCUMSTANCES:
<br />1. CEILING IS SUSPENDED.
<br />2. FLOOR FRAMING IS CONSTRUCTED OF TRUSS-TYP OPEN -WEB
<br />PERFORATED MEMBERS.
<br />1. MATERIALS:
<br />DRAFTSTOPPING MATERIALS SHALL NOT BE LESS THAN 1/2"
<br />GYPSUM BOARD, 3/8" WOOD STRUCTURAL PANELS OR OTHER
<br />APPROVED MATERIALS ADEQUATELY SUPPORTED.
<br />DRAFTSTOPPING SHALL BE INSTALLED PARALLELL TO THE
<br />FLOOR FRAMING MEMBERS UNLESS OTHERWISE APPROVED BY
<br />THE BUILDING OFFICIAL.
<br />SEPARATION FROM GARAGE:
<br />PER SECTION R302.5, R302.6, OPENING PROTECTION
<br />1. OPENINGS FROM A PRIVATE GARAGE DIRECTLY INTO A ROOM
<br />USED FOR SLEEPING PURPOSES SHALL NOT BE PERMITTED.
<br />OPENINGS BETWEEN THE GARAGE AND RESIDENCE SHALL BE
<br />EQUIPPED WITH SOLID OR HONYCOMB CORE STEEL AND NOT LESS
<br />THAN 1 3/8", 20 MINUTE RATED, WITH SELF CLOSER.
<br />2. THE GARAGE SHALL BE SEPARATED FROM THE RESIDENCE AND
<br />ITS ATTIC AREA BY NOT LESS TITAN 1/2" GYPSUM BOARD APPLIED
<br />TO THE GARAGE SIDE. GARAGES BENEATH HABITABLE ROOMS
<br />ABOVE BY NOT LESS THAN 5/8" TYPE "X" GYPSUM BOARD OR
<br />EQUIVALENT.
<br />CEILING CONSTRUCTION:
<br />1. THE GARAGE SHALL BE SEPARATED FROM THE RESIDENCE AND
<br />ITS ATTIC AREA BY NOT LESS THAN 1/2 INCH (12.7 mm) GYPSUM
<br />BOARD APPLIED TO THE GARAGE SIDE. GARAGES BENEATH
<br />HABITABLE ROOMS SHALL BE SEPARATED FROM ALL HABITABLE
<br />ROOMS ABOVE BY NOT LESS THAN 5/8 INCH (15.9 mm) TYPE "X"
<br />GYPSUM BOARD OR EQUIVALENT. WHERE THE SEPARATION IS A
<br />FLOOR -CEILING ASSEMBLY, THE STRUCTURE SUPPORTING THE
<br />SEPARATION SHALL ALSO BE PROTECTED BY NOT LESS THAN 1/2
<br />INCH (12.7 mm) GYPSUM BOARD OR EQUIVALENT.
<br />EXTERIOR FINISHES:
<br />1. CEMENT PLASTER FINISH OVER MASONRY SHALL BE 5/8" THICK
<br />TEXTURED PER COMMUNITY STANDARDS.
<br />2. CEMENT PLASTER FINISH OVER WOOD SUBSTRATE SHALL BE 7/8"
<br />THICK (3) COAT STUCCO OVER (2) LAYERS OF WATER RESISTANT
<br />BARRIERS IN ACCORDANCE WITH FLORIDA BUILDING CODE 6TH
<br />EDITION (2017) RESIDENTIAL, R703 AND ASTM C926. TEXTURE PER
<br />COMMUNITY
<br />FLASHING:
<br />1. FLASHING SHALL BE INSTALLED AT WALL AND ROOF
<br />INTERSECTIONS, DECK AND WALL INTERSECTIONS, AT GUTTERS,
<br />AT ALL CHANGES IN ROOF SLOPE OR DIRECTION, AND AROUND
<br />ROOF OPENINGS.
<br />2. APPROVED CORROSION -RESISTANT FLASHING SHALL BE APPLIED
<br />SHINGLE -FASHION IN A MANNER TO PREVENT ENTRY OF WATER
<br />INTO THE WALL CAVITY OR PENETRATION OF WATER TO THE
<br />BUILDING STRUCTURAL FRAMING COMPONENTS. SELF -ADHERED
<br />MEMBRANES USED AS FLASHING SHALL COMPLY WITH AAMA 711.
<br />THE FLASHING SHALL EXTEND TO THE SURFACE OF THE EXTERIOR
<br />WALL FINISH. APPROVED CORROSION -RESISTANT FLASHINGS
<br />SHALL BE INSTALLED AT ALL OF THE FOLLOWING LOCATIONS:
<br />3. EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT
<br />EXTERIOR WINDOW AND DOOR OPENINGS SHALL EXTEND TO THE
<br />SURFACE OF THE EXTERIOR WALL FINISH OR TO THE
<br />WATER -RESISTIVE BARRIER FOR SUBSEQUENT DRAINAGE.
<br />FLASHING AT EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE
<br />INSTALLED IN ACCORDANCE WITH ONE OR MORE OF THE
<br />FOLLOWING:
<br />• THE FENESTRATION MANUFACTURER'S INSTALLATION AND
<br />FLASHING INSTRUCTIONS, OR FOR APPLICATIONS NOT
<br />ADDRESSED IN THE FENESTRATION MANUFACTURERS
<br />INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING
<br />MANUFACTURERS INSTRUCTIONS. WHERE FLASHING
<br />INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PAN FLASHING
<br />SHALL BE INSTALLED AT THE SILL OF EXTERIOR WINDOW AND
<br />DOOR OPENINGS. PAN FLASHING SHALL BE SEALED OR SLOPED
<br />IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF
<br />THE EXTERIOR WALL FINISH OR TO THE WATER -RESISTIVE
<br />BARRIER FOR SUBSEQUENT DRAINAGE. OPENINGS USING PAN
<br />FLASHING SHALL ALSO INCORPORATE FLASHING OR PROTECTION
<br />AT THE HEAD AND SIDES.
<br />• IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A
<br />REGISTERED DESIGN PROFESSIONAL.
<br />• IN ACCORDANCE WITH FMA/AAMA 100, FMAIAAMA 200. FMA/WDMA
<br />250, OR FMAIAAMAIWDMA 300
<br />WINDOW INSTALLATION:
<br />1. WINDOWS SHALL BE INSTALLED AND FLASHED IN ACCORDANCE
<br />WITH THE MANUFACTURERS WRITTEN INSTALLATION
<br />INSTRUCTIONS. WRITTEN INSTALLATION INSTRUCTIONS SHALL BE
<br />PROVIDED BY THE MANUFACTURER FOR EACH WINDOW.
<br />FLOOD ZONE REQUIREMENTS:
<br />PLAN MEETS OR EXCEEDS FEMA FLOOD FINISHED GARAGE
<br />FLOOR ELEVATION.
<br />CHIMNEY HEIGHT REQUIREMENTS:
<br />1. WHEN STANDARD OR OPTIONAL FIREPLACE IS TO BE INSTALLED
<br />THE CHIMNEY MUST EXTEND Y-0" PAST THE HIGHER POINT WHERE
<br />IT EXTENDS THROUGH THE ROOF AND MUST BE T-0" HIGHER THAN
<br />THE ROOF OR RIDGE THAT IS 10'-0" AWAY OR CLOSER.
<br />TUB AND SHOWER AREAS:
<br />1. CEMENT, FIBER -CEMENT, OR GLASS MAT GYPSUM BOARD (NO
<br />GREEN BOARD ALLOWED) IN COMPLIANCE WITH ASTM C1288,
<br />C1325, OR C1178 AND INSTALLED IN ACCORDANCE WITH
<br />MANUFACTURER RECOMMENDATIONS SHALL BE USED AS
<br />BACKERS FOR WALL TILE IN TUB AND SHOWER AREAS, AND WALL
<br />PANELS IN SHOWER AREAS.
<br />MECHANICAL AND HVAC:
<br />1. ENERGY CALCULATIONS FOR HEATING AND COOLING
<br />CAPACITIES SHALL BE FURNISHED BY THE GENERAL
<br />CONTRACTOR AS AN ATTACHMENT TO THIS PLAN SET AT THE
<br />TIME OF APPLICATION FOR PERMIT.
<br />2. MECHANICAL APPLIANCES SHALL BE ACCESSIBLE FOR
<br />INSPECTION, SERVICE, REPAIR, AND REPLACEMENT WITHOUT
<br />REMOVING PERMANENT CONSTRUCTION, OTHER APPLIANCES,
<br />OR ANY OTHER PIPING OR DUCTS NOT CONNECTED TO THE
<br />APPLIANCE BEING INSPECTED, SERVICED, REPAIRED, OR
<br />REPLACED. A LEVEL WORKING SPACE AT LEAST 30 INCHES (762
<br />mm) DEEP AND 30 INCHES (762 mm) WIDE SHALL BE PROVIDED IN
<br />FRONT OF THE CONTROL SIDE TO SERVICE AN APPLIANCE.
<br />3. DUCTS IN THE GARAGE AND DUCTS PENETRATING THE WALLS OR
<br />CEILINGS SEPARATING THE DWELLING FROM THE GARAGE SHALL
<br />BE CONSTRUCTED OF A MIN. #26 GAUGE (0.48 mm) SHEET STEEL OR
<br />OTHER APPROVED MATERIAL AND SHALL HAVE NO OPENINGS INTO
<br />THE GARAGE.
<br />4. FOUNDATIONS AND SUPPORTS FOR OUTDOOR MECHANICAL
<br />SYSTEMS SHALL BE RAISED AT LEAST 3 INCHES (76 mm) ABOVE
<br />THE FINISHED GRADE AND SHALL ALSO CONFORM TO THE
<br />MANUFACTURER'S INSTALLATION INSTRUCTIONS.
<br />5. AUXILIARY DRAIN PAN. CATEGORY IV CONDENSING
<br />APPLIANCES SHALL BE PROVIDED WITH AN AUXILIARY DRAIN
<br />PAN WHERE DAMAGE TO ANY BUILDING COMPONENT WILL
<br />OCCUR AS A RESULT OF STOPPAGE IN THE CONDENSATE DRAIN
<br />PIPING SYSTEM. THESE PANS SHALL BE INSTALLED IN
<br />ACCORDANCE WITH THE APPLICABLE PROVISIONS OF SECTIONS
<br />M1411.3.
<br />EXHAUST FANS AND VENTING:
<br />1. OUTDOOR DISCHARGE. THE AIR REMOVED BY EVERY
<br />MECHANICAL EXHAUST SYSTEM SHALL BE DISCHARGED TO THE
<br />OUTDOORS. AIR SHALL NOT BE EXHAUSTED INTO AN ATTIC,
<br />SOFFIT, RIDGE VENT OR CRAWL SPACE.
<br />2. EXHAUST AIR FROM BATH ROOMS AND TOILET ROOMS SHALL
<br />NOT BE RECIRCULATED WITHIN A RESIDENCE OR TO ANOTHER
<br />DWELLING UNIT AND SHALL BE EXHAUSTED DIRECTLY TO THE
<br />OUTDOORS. EXHAUST AIR FROM BATHROOMS AND TOILET ROOMS
<br />SHALL NOT DISCHARGE INTO AN ATTIC, CRAWL SPACE, OR OTHER
<br />AREAS INSIDE THE BUILDING.
<br />3. DUCT LENGTH: THE MAXIMUM LENGTH OF A CLOTHES: DRYER
<br />EXHAUST DUCT SHALL NOT EXCEED 35 FEET. THE DRYER LOCATION
<br />TO THE WALL OR ROOF TERMINATION. THE MAXIMUM LENGTH OF
<br />THE DUCT SHALL BE REDUCED 2.5 FEET (762 mm) FOR EACH 45
<br />DEGREE (0.79 RAD) BEND AND 5 FEET (1524 mm) FOR EACH 90 DEGREE
<br />(1.6 RAD) BEND. THE MAXIMUM LENGTH OF THE EXHAUST DUCT
<br />DOES NOT INCLUDE THE TRANSITION DUCT. EXCEPTION - WHERE A
<br />CLOTHES DRYER BOOSTER FAN IS INSTALLED AND LISTED AND
<br />LABELED FOR THE APPLICATION, THE MAXIMUM LENGTH OF THE
<br />EXHAUST DUCT, INCLUDING ANY TRANSITION DUCT, SHALL BE
<br />PERMITTED TO BE IN ACCORDANCE WITH THE BOOSTER FAN
<br />MANUFACTURER'S INSTALLATION INSTRUCTIONS. WHERE A
<br />CLOTHES DRYER BOOSTER FAN IS INSTALLED AND NOT READILY
<br />ACCESSIBLE FROM THE ROOM IN WHICH THE DRYER IS LOCATED, A
<br />PERMANENT IDENTIFYING LABEL SHALL BE PLACED ADJACENT TO
<br />WHERE THE EXHAUST DUCT ENTERS THE WALL. THE LABEL SHALL
<br />BEAR THE WORDS "THIS DRYER EXHAUST SYSTEM IS. EQUIPPED
<br />WITH A REMOTELY LOCATED BOOSTER FAN."
<br />4. PROVIDE LOUVER DEVICES AT INTAKE AND
<br />EXHAUST LOCATIONS IN ACCORDANCE WITH
<br />AMCA STANDARD 550 IN FBC.
<br />ATTENTION GENERAL CONTRACTOR / BUILDER: ISSUANCE OF
<br />PLANS FROM THIS OFFICE SHALL NOT RELIEVE THE BUILDER OF
<br />RESPONSIBILITY TO REVIEW AND VERIFY ALL NOTES, DIMENSIONS,
<br />AND ADHERENCE TO APPLICABLE BUILDING CODES PRIOR TO
<br />COMMENCEMENT OF ANY CONSTRUCTION. ANY DISCREPANCY OF
<br />ERROR IN NOTES, DIMENSIONS, OR ADHERENCE TO APPLICABLE
<br />BUILDING CODES SHALL BE BROUGHT TO THE ATTENTION OF THE
<br />DRAFTER'S OFFICE FOR CORRECTION BEFORE COMMENCEMENT OF
<br />ANY CONSTRUCTION CORRECTION / REVISIONS. ANY REVISIONS OR
<br />CHANGES, NOT RELATED TO THE CORRECTION OF ERRORS THAT
<br />ARE MADE AFTER THE FINAL PLANS HAVE BEEN COMPLETED
<br />SHALL BE SUBJECT TO ADDITIONAL FEES. IF ANY MODIFICATIONS
<br />ARE MADE TO THESE PLANS BY ANY OTHER PARTY OTHER THAN
<br />THE DRAFTER'S OFFICE, THE DRAFTER SHALL NOT BE HELD
<br />RESPONSIBLE.
<br />FOUNDATION INSPECTION NOTES:
<br />A FOUNDATION SURVEY SHALL BE PERFORMED AND A COPY OF
<br />THE SURVEY SHALL BE ON SITE FOR THE BUILDING INSPECTOR'S
<br />USE, OR ALL PROPERTY MARKERS SHALL BE EXPOSED AND A
<br />STRING STRETCHED FROM MARKER TO MARKER TO VERIFY
<br />REQUIRED SETBACKS.
<br />FRAMING INSPECTION NOTES:
<br />ALL PLUMBING, ELECTRICAL, AND MECHANICAL ROUGH INS
<br />MUST BE COMPLETE, INSPECTED, AND APPROVED BEFORE
<br />REQUESTING THE FRAMING INSPECTION (FBC 110.6)
<br />JUN 0 8 2020
<br />�0\ 111111 /j/G.
<br />���
<br />VNo,"arF -�®
<br />W
<br />W
<br />Luz0=
<br />o >. F-
<br />>o ¢o
<br />LLI C, l-
<br />cnUWw
<br />Q Z) W
<br />J In W W
<br />!r Ir lY
<br />06ZOO
<br />W
<br />Z
<br />Lu -� Q
<br />_3cno00
<br />Z) Z LL cn
<br />�F--QZO
<br />g
<br />rt-
<br />Qo
<br />O
<br />H
<br />0
<br />r�
<br />V
<br />o
<br />(n
<br />m
<br />W
<br />kq
<br />lono
<br />®
<br />Z
<br />0
<br />w
<br />w
<br />ME="
<br />w
<br />Z
<br />w
<br />r(L
<br />v)
<br />me,
<br />0
<br />w
<br />.w
<br />Z
<br />O
<br />r
<br />lx
<br />U)
<br />W
<br />0
<br />c
<br />Z
<br />O
<br />uj
<br />u,
<br />4
<br />Z
<br />aaaaa
<br />i
<br />i
<br />i
<br />i
<br />COMMUNITY:
<br />LINKS AT CALUSA
<br />SPRINGS !
<br />PLAN # 6102
<br />RELEASED: S/14/20
<br />SHEET i
<br />CS2
<br />z
<br />_u
<br />:n
<br />z
<br />D
<br />z
<br />A
<br />2
<br />D
<br />z
<br />z
<br />z
<br />Q
<br />r
<br />D
<br />T
<br />D
<br />i
<br />z
<br />Q
<br />z
<br />n
<br />J
<br />D
<br />0
<br />D
<br />r
<br />i
<br />r
<br />L
<br />n
<br />
|