Laserfiche WebLink
I I d I III I It 11 _11L 1 -1 1 11 1 1 1 <br />FOLD UP WEATHER <br />RESISTIVE BARRIER & WEATHER RESISTIVE <br />TEMPORARILY SECURE BARRIER DOOR ROUGH OPENING WINDOW UNIT <br />WEATHER SLOPE <br />R IVE 0.3 in: 12.0 in <br />BARRIER WOOD FRAME CONSTR. <br />EXTERIOR 1 (0.6 cm: 30.5 cm) <br />TAPE SELF -ADHERED FLASXHING 1/ 3/4" _1" BEAD OF CONSTR. <br />SHEATHING BY LAPPING DOWN ADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING <br />OVER RIM JOIST AN THRESHOLD OF DOOR AND RETURN <br />WALL BY 6 IN. UP JAMB 6". USE LIQUID NAIL BRAND <br />IMBLED WINDOW) OR EQUAL WEATHER PROOF CAULKING EXTERIOR <br />CEMT. FIN. <br />WEATHER SELF -ADHERED FLASHING BUILDING PAPER <br />RESISITIVE <br />BARRIER SEAL TOPS OF JOIS WIRE LATH <br />)TS <br />UNDER DECKING SUBFLOOR <br />(SEE DETAIL WI <br />SELF -ADHERED FLASHING <br />HEAD FLASHING TIE-IN INSTRUXTIONS: <br />1 . Cut, fold up & temporarily secure weather resistive RIM JOIST <br />THESE DETAILS ARE GENERIC A D barrier above header to allow for flashing <br />installation <br />MEANT TO SHOW GENERAL FLASHING 2. Self -adhered flashing plus head flashing under <br />AND WATERPROOFING METHODS TO weather resistive barrier <br />BE USED. 3. Fold weather resistive barrier back over head <br />flashing and seal with tape <br />SELF -ADHERED FLASHING Scale: NTS SELF -ADHERED FLASHING SELF -ADHERED FLASHING <br />FLANGED WINDOW EXTERIOR DOOR WITH DECK - SECTION A CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER <br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER <br />EXTERIOR SHEATHING MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT <br />EXTERIOR SHEATHING 3/4"-l" BEAD OF CONSTR. INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE <br />ADHESIVE TO BE APPLIED UNDER FLASH�NG JAMB & HEAD THROUGH SELF -ADHERED <br />THRESHOLD OF DOOR AND RETURN FLASH NG, SEE FLASHING SELF -ADHERED FLASHING <br />UP JAMB 6". USE LIQUID NAIL BRAND FLANGED WINDOW <br />OR EQUAL WEATHER PROOF CAULKING (SEE DETAIL WP01) <br />REFER TO TECHNICAL SCORED <br />LETTER ON CHEMICAL RELEASE PAPER <br />COMPATIBILITY <br />C RN <br />SELF_A <br />E <br />D <br />R ... <br />S ASPH LT ADHE <br />HERED Sr <br />I SEI �PER <br />SELF -ADHERED FLASHING SELF -ADHERED FLASHING, (BEFORE FOLDING, SCORE <br />RELEASE PAPER TO EXPOSE <br />EXTEND A MINIMUM 6" ADHESIVE AS SHOWN) <br />VERTICALLY FROM <br />BOTTOM OF <br />0 THRESHOLD <br />SECTION -A (SEE DETAIL WP02) <br />CN <br />LO <br />r1_ <br />LID <br />Vq <br />E <br />0 <br />LZ <br />LLJ <br />M <br />D <br />1L <br />*J 1 SELF -ADHERED FLASHING <br />SELF -ADHERED FLASHING <br />NAILING FLANGE 1 <br />2 SEAL TOPS OF JOISTS <br />DO NOT FLASH OVER UNDER DECKING <br />BOTTOM NAILING 8 (SEE DETAIL WP07) <br />FLANGE <br />-IT <br />i 1 101 M M :1 L51 <br />SELF -ADHERED FLASHING <br />HALF ROUND WINDOW <br />r_L1-%QnIIN%J . ­ ...­ <br />SELF -ADHERED FLASHING <br />DECK JOIST <br />.E <br />AM <br />SELF-ADHER <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK <br />SELF -ADHERED FLASHING <br />OUTSIDE CORNER <br />PLASTER STOP <br />CONTINUOUS BACKER <br />ROD & SEALANT <br />0 <br />SELF -ADHERED FLASHING <br />PATCH <br />IHERED FLASHING <br />STRIP OF SAF <br />DRAINAGE PLANE WRB <br />BOND BREAK WRB <br />SF LATH <br />WRAP I WRB ONTO <br />THE VERTICAL <br />SURFACE TO TOP OF <br />FLANGE AS AN AIR <br />BARRIER <br />3-1/2" INCH FLANGE <br />1 <br />2 <br />4 <br />5 <br />THIS GAP IS A RESULT OF <br />NATURAL SHRINKAGE. <br />DO NOT SEAL. <br />DRIP SCREED PLASTIC <br />ACCESSORY <br />SOFFIT/CANTI LEVER <br />00111 <br />SELF -ADHERED FLASHING <br />INSIDE CORNER <br />-7 Ground 7 <br />Water Resistant Barrier <br />Lath <br />Sheathing <br />Stucco <br />FOUNDATION WEEP SCREED <br />LEGEND <br />SELF ADHERED FLASHING I _0 0 <br />DRAINAGE PLANE (DP) WEATHER RESISTANT <br />BARRIER (WRB) <br />BOND BREAK WEATHER RESISTANT BARRIER <br />SELF FURRING (SF) LATH <br />PLASTER ACCESSORY <br />SHEATHING, *OSB', PLYWOOD, DENSGLASS <br />ER STOP A <br />NUOUS BACKER ROD <br />-ANT <br />ITITIOUS FINISH <br />STRUCTURAL FRAMING <br />STRUCTURAL SHEATHING <br />STRIP OF SAF <br />DRAINAGE PLANE WRB <br />BOND BREAK WRB <br />SF LATH <br />FLASHING REQUIREMENTS. <br />R609.1 Flashing, Sealants and Weatherstripping. Flashing and sealants for exterior windows shall comply with Section R703.8. <br />R703.2 Weather -resistant sheathing paper. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D 226 for Type 1 felt or <br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less than 6 inches (152 <br />mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and building appendages in a manner <br />to meet the requirements of the exterior wall envelope as described in Section R703.4 <br />Exception: Omission of the water -resistive barrier is permitted in the following situations: <br />1. In detached accessory buildings. <br />2. Under exterior wall finish materials as permitted in Table II <br />3. Under Paperbacked stucco lath when the paper backing is an approved water -resistive barrier. <br />R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into thewall cavity or <br />penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with AAMA 711. The <br />flashing shall extend to the surface of the exterior wall finish. Approved corrosion -resistant flashings shall be installed at all of the following locations: <br />1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface ot he exterior wall finish or to the <br />water -resistive barrier for subsequent drainage. Flashing at exterior window and door openings shall be installed in accordance with one or more ofthe <br />following or other approved method: <br />1.1 The fenestration manufacturer's written flashing instructions. <br />1.2 The flashing manufacturer's written installation instructions. <br />1.3 In accordance with FMA/AAMA 100, FMA/AAMA 200, or FMA/WDMA 250. <br />1.4 In accordance with the flashing method of a registered design professional. <br />2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under stucco copings. <br />3. Under and at the ends of masonry, wood or metal copings and sills. <br />4. Continuously above all projecting wood trim. <br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. <br />6. At wall and roof intersections. <br />7. At built-in gutters. <br />R703.6.2.1 Weep Screeds <br />A Minimum 0.01 9-inch (No. 26 Galv. sheet gage), corrosion -resistant weep screed or plastic weep screed, with a minimum vertical attachment flange of <br />3 1/2" shall be provided at or below the foundation plate line on exterior stud walls in accordance with ASTM C 926. <br />SELF -ADHERED FLASHING <br />PRODUCTS DETAILS. <br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND <br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC R703.2.1 <br />Detail Instructions <br />Refer to the number marked as G in each detail that corresponds to the numbered items in the list of <br />instructions below: <br />1 . Install self -adhered flashing in order as shown by numbers <br />2. Install flashing and weather resistive barrier to form water shedding laps <br />3. Self -adhered flashing can be substituted for building paper <br />4. Split the release paper using the ripcord (Split release on demand, embedded in the adhesive layer) - <br />for ease of installation and to minimize scoring cuts <br />5. Remove all release paper per standard installation instructions and adhere to substrate using a square <br />piece of flashing material (I x 6" Minimum) <br />6. Fold as shown by arrows <br />7. Angle of corner may vary, adjust folding of the flashing accordingly to fit tight to corner <br />8. Mechanically fasten as necessary <br />Cement Plaster <br />in accordance <br />with ASTMC926 <br />over wood 2nd <br />floor <br />Cement <br />Plaster <br />over block <br />1 st floor <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />Felt backed metal <br />lathe in accordance <br />with ASTMIC 1063 <br />Building Paper <br />7/16" O.S.B. <br />sheathing <br />Metal <br />Flashing <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />Maintain <br />Bottom of <br />Weep Screed <br />1 1/2" to 2" <br />Above Roof <br />Sheathing <br />Note: <br />The building paper and metal lath must be <br />installed over the top of the weep screed. I <br />WEEP SCREED DETAIL <br />SCALE: NOT TO SCALE <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />Felt backed metal <br />lathe in accordance <br />with ASTMIC 1063 <br />Building Paper <br />7/16" O.S.B. <br />sheathing <br />-Stampecle or similar <br />cauk bottom <br />joint only <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />1/2" Cementitious <br />Decorative Finish <br />All inside and <br />outside comer will <br />need to be miter <br />cut and caulked all <br />butt joints need to <br />becaulked using <br />Stampede or sim. <br />caulk for all <br />rp �7 <br />L ul <br />C, <br />U) <br />(Z) CD <br />L.0 <br />LU <br />E <br />I <br />04 <br />C*, <br />S) to C2 <br />'0 C', <br />.1 " <br />0 <br />_r_ U_ 00 <br />-5 - OD <br />0 (13 <br />< 0 <br />CL C) <br />0 < 0 <br />A1 <br />U D. <br />-1 C B-D C <br />Y <br />Iwo <br />ag <br />UA <br />Lu <br />U0 - 0Z <br />Z <br />cc <br />= -2= C, <br />Z 'ffi 0 -.2 <br />M E M <br />M <br />< M LM <br />W'WW FDSENG COM L.1 Li <br />S�2 <br />C=) <br />00 <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2017 Florida Building Code - <br />Residential 6th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineees signature and seal. <br />LENIMAR <br />4600 W. Cypress St, Suite 200 1 Tampa, FL 33607 <br />www.LennarTampa.com <br />0 Z <br />2 <br />U) <br />U, <br />Z <br />Z <br />LU cr <br />U400 <br />R.ZZ <br />Lu <br />U) <br />OD <br />LO <br />Z <br />0 <br />> <br />LU <br />Z Z <br />C) <br />Z <br />LL. <br />0 <br />C? <br />0 <br />0 <br />Z <br />:J UJ <br />U <br />Lr) <br />LLJ <br />8*1 '9 <br />9 R OZ <br />r- Se r- <br />F- <br />0 <br />Lr) <br />< <br />< <br />< <br />Z <br />Z <br />�j <br />LU <br />Lr) <br />T__I <br />" I <br />LIJ <br />di <br />2: <br />< <br />R�Z8 <br />;;�- �� Qu <br />1,0 <br />Z <br />Z <br />U) 8 <br />IS <br />0 <br />C� <br />Z <br />rn <br />T--q <br />SCALE AS NOTED <br />DATE 4/12/2019 <br />TECH: IBERCHAL <br />VERSION NO 5ml <br />SHEET NO. <br />W P <br />