Laserfiche WebLink
FOLD UP WEATHER <br />RESISTIVE BARRIER & <br />WEATHER RESISTIVE <br />WINDOW UNIT <br />FLASHING REQUIREMENTS <br />TEMPORARILY SECURE <br />BARRIER <br />DOOR ROUGH OPENING <br />WEATHER <br />RESISITIVE <br />SLOPE <br />0.3 in : 12.0 in <br />R612.10 Flashing, Sealants and Weatherstripping. Flashing and sealants for exterior windows shall comply with Section R703.8. <br />9 PP 9 9 P Y <br />BARRIER <br />TAPE <br />EXTERIOR <br />WOOD FRAME CONSTR. <br />SELF -ADHERED FLASHING 3/4"-1" BEAD OF CONSTR. <br />( 0.6 cm: 30.5 cm) <br />R703.2 Weather -resistant sheathing paper. One layer of No.15 asphalt felt, free from holes and breaks, complying with ASTM D 226 for Type 1 felt or <br />3 <br />SHEATHING <br />BY LAPPING DOWN ADHESIVE TO BE APPLIED UNDER <br />SELF -ADHERED FLASHING <br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied horizontally, <br />OVER RIM JOIST AND UP THRESHOLD OF DOOR AND RETURN <br />with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less than 6 inches (152 <br />(ASSEMBLED WINDOW) <br />WALL BY 6 IN. UP JAMB 6". USE LIQUID NAIL BRAND <br />OR EQUAL WEATHER PROOF CAULKING <br />EXTERIOR <br />mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and building appendages in a manner <br />2 <br />CEMT. FIN. <br />to meet the requirements of the exterior wall envelope as described in Section R703.1 <br />WEATHER <br />SELF -ADHERED FLASHING <br />BUILDING PAPER <br />RESISITIVE <br />Exception: Omission of the water -resistive barrier is permitted in the following situations: <br />2 <br />BARRIER <br />SEAL TOPS OF JOISTS <br />WIRE LATH <br />1. In detached accessory buildings. <br />1 <br />UNDER DECKING SUBFLOOR <br />2. Under exterior wall finish materials as permitted in Table R703.4 <br />SELF -ADHERED FLASHING <br />(SEE DETAIL WP07) <br />3. Under Paperbacked stucco lath when the paper backing is an approved water -resistive barrier. <br />HEAD FLASHING TIE-IN INSTRUXTIONS: <br />R703.8 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into thewall cavity or <br />1. Cut, fold up & temporarily secure weather resistive <br />RIM JOIST <br />penetration ofwater to the building structural framing components. Self -adhered membranes used as flashing shall comply with AAMA 711. The <br />barrier above header to allow for flashing <br />flashing shall extend to the surface of the exterior wall finish. Approved corrosion -resistant fleshings shall be installed at all of the following locations: <br />THESE DETAILS ARE GENERIC AND <br />installation <br />MEANT TO SHOW GENERAL FLASHING <br />AND WATERPROOFING METHODS TO <br />2. Self -adhered flashing plus head flashing under <br />weather resistive barrier <br />1 <br />1 <br />1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of he exterior wall finish or to the <br />water -resistive barrier for subsequent drainage. Flashing at exterior window and door openings shall be installed in accordance with one or more of the <br />3. Fold resistive barrier back head <br />BE USED. <br />weather over <br />flashing and seal with tape <br />2 <br />2 <br />O <br />following or other approved method: <br />1.1 The fenestration manufacturer's written flashing instructions. <br />1.2 The flashing manufacturer's written installation instructions. <br />Scale: NTS <br />SELF -ADHERED FLASHING <br />FLANGED WINDOW <br />N <br />SELF -ADHERED FLASHING <br />/ <br />SELF -ADHERED FLASHING <br />' <br />1.3 In accordance with FMA/AAMA 100, FMA/AAMA 200, or FMA/WDMA 250. <br />EXTERIOR DOOR WITH DECK - SECTION A <br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER <br />1.4 In accordance with the flashing method of a registered design professional. <br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER <br />2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under stucco copings. <br />3. Under and at the ends of masonry, wood or metal copings and sills. <br />EXTERIOR SHEATHING <br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT <br />4. Continuously above all projecting wood trim. <br />EXTERIOR SHEATHING <br />3/4"-1" BEAD OF CONSTR. INSTALL SELF -ADHERED <br />NEEDED IN CORNERS ADHESIVE <br />ASPHALT ADHESIVE <br />THROUGH SELF -ADHERED <br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. <br />P Y <br />�► <br />ADHESIVE TO BE APPLIED UNDER FLASHING JAMB & HEAD <br />THRESHOLD OF DOOR AND RETURN FLASHING, SEE <br />FLASHING SELF -ADHERED FLASHING <br />6. At wall and roof intersections. <br />UP JAMB 6". USE LIQUID NAIL BRAND FLANGED WINDOW <br />7. At built -In gutters. <br />OR EQUAL WEATHER PROOF CAULKING (SEE DETAIL WP01) <br />REFER TO TECHNICAL <br />LETTER ON CHEMICAL , <br />O <br />SCORED <br />RELEASE PAPER <br />R703.6.2.1 Wee Screeds <br />P <br />COMPATIBILITY <br />A Minimum 0.019-inch (No. 26 Galy. sheet gage), corrosion -resistant weep screed or plastic weep screed, with a minimum vertical attachment flange of <br />SELF -ADHERED FLASHING <br />SELF -ADHERED FLASHING, <br />�o (BEFORE FOLDING, SCORE <br />3 1/2" shall be provided at or below the foundation plate line on exterior stud walls in accordance with ASTM C 926. <br />EXTEND A MINIMUM 6" <br />RELEASE PAPER TO EXPOSE <br />ADHESIVE AS SHOWN) <br />VERTICALLY FROM <br />BOTTOM OF <br />THRESHOLD <br />SECTION -A (SEE DETAIL WP02) <br />SELF -ADHERED FLASHING <br />SELF -ADHERED FLASHING <br />O <br />PRODUCTS DETAILS <br />V 2 <br />2 <br />SELF -ADHERED FLASHING <br />5 <br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND <br />NAILING FLANGE 1W" <br />4 <br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC R703.2 <br />DO NOT FLASH OVER <br />2 <br />SEAL TOPS OF JOISTS <br />UNDER DECKING <br />1 <br />6 <br />Detail Instructions <br />Refer to the number marked as #Oin each detail that corres to the items in the list <br />BOTTOM NAILING <br />FLANGE <br />8 <br />(SEE DETAIL WP07) <br />2 <br />7 <br />ponds numbered of <br />instructions below: <br />1. Install self -adhered flashing in order as shown by numbers <br />SELF -ADHERED FLASHING <br />1 <br />SELF -ADHERED FLASHING <br />, <br />SELF -ADHERED FLASHING I LTD 1 <br />HALF ROUND WINDOW <br />EXTERIOR DOOR WITH DECK <br />INSIDE CORNER • <br />2. Install flashing and weather resistive barrier to form water shedding laps <br />3. Self -adhered flashing can be substituted for building paper <br />4. Split the release paper using the ripcord (Split release on demand, embedded in the adhesive layer) - <br />�Ground� <br />for ease of installation and to minimize scoring cuts <br />5. Remove all release paper per standard installation instructions and adhere to substrate using a square <br />SHEATHING <br />piece of flashing material (6" x 6" Minimum) <br />1 <br />6. Fold as shown by arrows <br />7. Angle of corner may vary, adjust folding of the flashing accordingly to fit tight to corner <br />Water Resistant Barrier <br />g Mechanically fasten as necessary <br />Lath <br />SELF -ADHERED FLASHING <br />Sheathing <br />PATCH <br />Stucco <br />° ° a <br />7/8" Cement Plaster <br />DOUBLE <br />a ° <br />in accordance with <br />° ° <br />ASTMC926 <br />JOIST <br />o a a a <br />° <br />7/8" Cement Plaster <br />SINGLE <br />WOOD BEAM <br />1 <br />Foundation Wall , ° <br />Felt backed metal in accordance with <br />JOIST <br />BELOW <br />SELF -ADHERED FLASHING <br />° <br />lathe in accordance ASTMC926 <br />SELF -ADHERED FLASHING <br />1 <br />a a a a a <br />with ASTMC1063 <br />° <br />Felt backed metal <br />2 <br />° ° <br />k. Building Paper lathe in accordance <br />SELF -ADHERED <br />SELF -ADHERED <br />3" MIN <br />4 <br />with ASTMC1063, <br />FLASHING <br />FLASHING Q <br />5 <br />�',' 7/16" O.S.B. <br />' Building Paper <br />�', sheathing <br />i , <br />7/16" O.S.B. <br />Metal ' <br />' sheathing <br />SELF -ADHERED FLASHING <br />' <br />SELF -ADHERED FLASHING <br />FOUNDATION WEEP SCREED <br />Flashing ' <br />DECK JOIST <br />OUTSIDE CORNER <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />Maintain <br />Bottom of Stampede or similar <br />Weep Screed cauk bottom <br />1 1/2" to 2" joint only <br />Above Roof Weep Screed <br />Sheathing Installed As Per <br />Manufact. Specs. <br />1/2" Cementitious <br />Cement Plaster <br />in accordance Decorative Finish <br />with ASTMC926 o,o•0 All inside and <br />oeQ,�.o <br />over wood 2nd ,o , o <br />outside corner will <br />floor ••�•°•o,o,o need to be miter <br />cut and caulked all <br />'•°•o,®o,®,o•: butt joints need to <br />becaulked using <br />�•°•0 <br />8 .� <br />Stampede or sim. <br />caulk for all <br />Note: <br />The building paper and metal lath must be <br />Cement installed over the top of the weep screed. <br />Plaster <br />over block <br />1 st floor <br />WEEP SCREED DETAIL <br />NOT USED <br />, <br />NOT USED <br />NOT USED <br />SCALE: NOT TO SCALE <br />Z r`) <br />- o <br />Q <br />J <br />t2 <br />IC� Z <br />nt,n.� i <br />� c�D <br />w <br />•Q <br />u - <br />m <br />OLU <br />C <br />LA ZD <br />o <br />o m <br />no <br />U <br />LU E <br />Iv M <br />C (am <br />0 O <br />..., 2 (Li <br />a) <br />yLLco <br />m <br />ce <br />U <br />(I)� <br />C <br />a o <br />Y <br />Q <br />to0. O V <br />0. <br />Q O <br />A' <br />B D. <br />NCRDC <br />ti <br />N <br />N <br />N <br />.w Cc,Z,rn <br />V y N p = <br />o m <br />Z <br />M I\ <br />Z F 2 T Z <br />cc:O <br />� O O <br />O <br />LL Z <br />J <br />LL <br />lL N <br />W ago <br />LLl <br />° a <br />QW VQac� <br />z <br />Z vU� <br />O ioCC <br />20 <br />CV O <br />OO <br />m m <br />A <br />Z LLC <br />a <br />J <br />W a M= <br />N <br />Cr Q <br />❑ ❑ <br />To the best of the Engineer's knowledge, information, and <br />belief, the structural plans and specifications contained <br />within these drawings comply with the Florida Building <br />Code 5th Edition (2014) Residential. Engineer's signature <br />and seal is only for the structural engineering portions of <br />the drawing pages bearing Engineer's signature and seal. <br />0 <br />0 <br />Z N <br />O�l� <br />i> J) ro <br />QU-) fuU') <br />Z <br />oC U <br />Q <br />Z E .0 <br />W <br />Z <br />J � <br />d- <br />oZ <br />O <br />W LL <br />W Z V) d <br />mZ <br />vl- R 0 <br />OZ}ZaU <br />zQQUUQQ <br />Z L Z <br />Oa�3oo <br />UI-aOZO <br />M <br />��LLI <br />0 <br />3 <br />U) <br />Lr) <br />(V <br />J <br />� <br />Q <br />F- < <br />a <br />WZUZ�tnWgOQZ <br />Q <br />POz_rai0 <br />LL <br />� <br />0Z <br />Q) <br />O <br />wZ0 <br />c7w <br />_J uU la- a')aUP <br />O�WoILZQ <br /><aaog <br />0 X LL Z <br />Z <br />W <br />a <br />auJ <br />0LU 0. <br />Q~� <br />z <br />o <br />M <br />LL <br />> <br />O <br />15Z1­4 <br />J <br />a <br />SCALE : AS NOTED <br />PLOT DATE: 12/7/2012 <br />TECH: FFLORES <br />VERSION NO. <br />1525 <br />JOB NO: 17-5172 <br />SHEET NO. <br />