Laserfiche WebLink
I It, II r:. 111111 _ _ .I 4rR I I <br />M <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />T.O.M. <br />HDR HGT. <br />6" FASCIA <br />(TYP) <br />TEXTURED — <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP.) <br />F.FL. <br />12 T_ = 12 <br />5 <br />-- _ 12 <br />3 TAB SHINGLES. ROOF _ <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />1' 0" <br />----------------------------- -- — — <br />0 00 ao <br />El <br />El a a0 <br />12 <br />5� <br />15'-0" RIDGE VENT <br />---------------------HEEL <br />5 <br />i F4 T.O.M. <br />— HDR HGT. <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />bo <br />(TYP.) <br />co <br />�7------ ---F.FL. <br />--------------------— <br />14'-0" RIDGE VENT <br />12 <br />�5 <br />N <br />-------------------------------------- - ------------------------- - ----------------------------------------------------- <br />FRONT ELEVATION — Al <br />RIGHT ELEVATION — Al <br />1 /4"=1' <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior plaster. <br />Installation of these materials shall be in compliance with ASTM C <br />926 and ASTM C 1063. <br />R703.7.1 Lath. <br />All Lath and lath attachments shall be of corrosion -resistant <br />materials. Attached per ASTM C 1063. <br />R703.7.2 Plaster. <br />Plastering w/ portland cement plaster shall be not less than three <br />coats when applied over metal lath or wire lath and shall be not <br />less than two coats when applied over masonry, concrete. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed where cement plaster <br />(stucco) is to be applied over wood -based sheathing, shall include <br />a water -resistive vapor -permeable barrier. The individual layers <br />shall be installed independently such that each layer provides a <br />separate continuous plane and any flashing intended to drain to <br />the water -resistive barrier is directed between the layers. The <br />barriers shall consist of one of the following. <br />1. Two layers of an approved water resistant barrier material in <br />accordance with R703.2. <br />2. One layer of an approved water -resistive barrier (paper <br />backed stucco lath) over an approved synthetic house wrap. <br />R703.4 Flashing. <br />Approved corrosion -resistant flashing shall be applied <br />shingle -fashion in a manner to prevent entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. Flashing shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry constructions with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersections <br />• At Built-in gutters. <br />Attic Ventilation <br />Attic Ventilation to be in compliance with the Florida Building Code 6th Edition <br />(2017) Residential R806. <br />The Minimum net free ventilating area shall be 11150 of the area of the vented <br />space. The ventilating area may be reduced to 11300 provided that at least 40% <br />but no more than 50% of the required ventilation is provided in the upper portion of <br />the space to be ventilated.Upper ventilators shall be located no more than 3 feet <br />(measured vertically) below the ridge or highest pant of the space, with the <br />balance of the required ventilation provided by eave or comice vents. <br />-CALCULATIONS BASED ON THE FOLLOWING VALUES, SEE ROOF PLAN" <br />(Values to be verified with Manufacturer Specifications) <br />• RIDGE VENTS 15 SO. IN. OF NET FREE AREA / LINEAR FT. <br />• OFF -RIDGE VENTS 138 SQ. IN. OF NET FREE AREA / UNIT <br />• SOFFIT VENTS 7 SQ. IN. OF NET FREE AREA / SO. FT. <br />0 <br />o G <br />z N <br />z g <br />J (7 <br />d N <br />z <br />Wv) a <br />^, o <br />VJ tL <br />(10 u, <br />U � <br />Ow � <br />1nc�,E <br /><n ZD <br />o <br />U Z5 a <br />• <br />Q o <br />N �O <br />(Y <br />Ni� v`�- z <br />§No <br />Z dM o w <br />�� u ❑i <br />.o <br />W y m V q W <br />a N �Z: q <br />Z V�i'f�t��ifrr,p <br />Q <br />O <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2017 Florida Building Code - <br />Residential 6th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />w <br />CO <br />M <br />a <br />o <br />z o <br />Z <br />g <br />LJL <br />ce E <br />a O <br />-�o <br />i <br />» <br />¢ s <br />Z® <br />H rD <br />0 <br />O E <br />x� <br />Up <br />a H <br />o a <br />SO <br />Z <br />C <br />N� <br />w i <br />z <br />ao <br />�di <br />aZ <br />¢z <br />m0 <br />Nc <br />�y°z <br />Z <br />J <br />Fw <br />000�d <br />w <br />Z <br />go <br />oLL <br />O <br />�z <br />0" <br />�0. <br />a <br />C.0 <br />�t <br />za <br />�3 <br />C0 <br />0 <br />.N <br />W <br />,! <br />N <br />CIO <br />> <br />0 <br />ca <br />`/ <br />T <br />U <br />in 0) <br />V J <br />T^— <br />s J <br />to N <br />L <br />r <br />T <br />N <br />M co a) <br />m <br />Z <br />r M <br />E 0 <br />z <br />f° <br />a <br />E <br />U � Q p <br />c <br />JOB <br />NO: 19-5331 <br />SCALE : AS NOTED <br />SHEET NO. <br />3.1 <br />