Laserfiche WebLink
PURLIN <br />PURLIN <br />(BY M.B.M.) <br />ATTACHMENT BY OTHERS <br />DO .NOT DRILL HOLES INTO <br />THE FLANGES <br />—CLAMP <br />NOTE: M.B.M. only provides the <br />Flange C—Clamp : not roof purlin. All ether material EAVE COVER TRIM <br />an acceptable connection and hardware is by others. <br />(IF PRESET <br />r, <br />vended Connection Detail <br />MANY FACTORS BEYOND THE CONTROL OF THE METAL BUILDING SUPPLIER AFFECT THE ABILITY <br />OF A PURLIN TO SAFELY SUPPORT HANGING LOADS COMBINED WITH OTHER REQUIRED ROOF <br />LOADS. DUE TO THE VARIABLES INVOLVED IN HANGING LOADS AND THEIR ATTACHMENTS TO <br />THE PURLINS, THE METAL BUILDING SUPPLIER CANNOT ASSURE THAT THE PURLINS FOR A <br />PARTICULAR BUILDING PROJECT CAN SAFELY SUPPORT THE MAXIMUM ALLOWABLE HANGING LOADS <br />IN COMBINATION WITH OTHER ROOF LOADS. <br />IT IS THE RESPONSIBILITY OF THE HANGER SYSTEM INSTALLER TO COORDINATE WITH THE ENGINEER <br />OF RECORD FOR THE OVERALL PROJECT TO ENSURE A SAFE HANGING LOAD INSTALLATION. THE <br />METAL BUILDING ENGINEER IS NOT THE ENGINEER OF RECORD FOR THE OVERALL PROJECT. <br />WITHOUT SPECIFIC CERTIFICATION FOR INDIVIDUAL HANGING LOADS, THE NET EFFECTS OF APPLIED <br />HANGER LOADS INSTALLED ON A PARTICULAR PURLIN SHALL NOT EXCEED THE NET EFFECTS OF <br />THE CERTIFIED UNIFORMLY APPLIED DESIGN COLLATERAL LOAD. <br />HANGING LOADS SHOULD NOT BE APPLIED TO THE PURLIN LIP. INHERE PERMISSIBLE, THE BEST <br />PRACTICE FOR HANGING LOADS IS TO ATTACH TO THE PURLIN WEB USING A BOLT AND NUT, OR <br />SELF —DRILLING SCREWS. <br />HANGING UNIFORM LOADS SUCH AS SPRINKLER MAINS OR HVAC EQUIPMENT SHOULD BE DISTRIBUTED <br />OVER SEVERAL PURLINS, AND SHOULD NEVER EXCEED THE COLLATERAL LOAD ALLOWANCE <br />FOR THE ROOF SYSTEM. FOR UNIFORM LOADS THAT RUN PARALLEL TO THE PURLINS, IT MAY BE <br />NECESSARY TO USE TRANSVERSE: SUPPORT CHANNELS( A. A. TRAPEZE BEAMS) ATTACHED TO THE <br />WEBS OR FLANGE OF ADJACENT PURLINS TO SPREAD THE LOAD BETWEEN TWO OR MORE PURLINS. IN <br />SUCH CASES, CONTACT THE BUILDING MANUFACTURER OR A LOCAL PROFESSIONAL ENGINEER PRIOR TO <br />ATTEMPTING TO HANG LOADS FROM THE PURLINS <br />GUTTER <br />00 NOT INSTALL GUTTER WITH <br />OUTSIDE FACE PERPENDICULAR <br />TO THE GROUND. <br />!j <br />Ll <br />DOWNSPOUT OFFSET GUIDE <br />FOR SIDEWALLS WITHOUT WALL PANELS <br />(REFER TO TRIM DETAILS FOR STRAP <br />AND FASTENER INSTALLATION INSTRUCTIONS!) <br />INSTALL GUTTER WITH <br />OUTSIDE FACE PERPENDICULAR <br />TO THE ROOF. <br />GUTTER <br />STRAIC <br />DOWNSF <br />FLG I� <br />P� <br />DOWNc <br />OFF; <br />[TYP E 'A' <br />W <br />Z <br />O <br />F_ <br />C <br />C <br />CL <br />`� <br />E— <br />LL <br />W <br />FLG <br />DOWNSPOUT OFFSET GUIDE <br />FOR PARTIAL SIDEWALLS WITH WALL PANELS <br />(REFER TO TRIM DETAILS FOR STRAP <br />AND FASTENER INSTALLATION INSTRUCTIONS!) <br />ISSUE ';_ DET CHI DATE <br />RCE INVESTMENT GROUP, LLC <br />gym: <br />TRUMP PLACE BOAT & RV STORAGE <br />w+Q <br />1 <br />