Laserfiche WebLink
12 <br />5� <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />Ll <br />E7 1:1 El E FE] FE11 7F <br />7E:1 E F-711 1�1 [711 El 0 L=� <br />El E ID-1 El E] El F[7�1 <br />------------- <br />14'-0" RIDGE VENT <br />12 <br />5� <br />N <br />I <br />12 <br />�5 <br />HEEL <br />12 <br />5� <br />6 <br />------ T.O.M. <br />— HDR HGT. <br />FRONT ELEVATION - Al <br />12 <br />SCALE: 1 /4"=1'-0" <br />15'-0" RIDGE VENT <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />T.O.M. <br />— — — — — — — — — — — — — — — — <br />HDR HGT. <br />1'-0" <br />3'-0" TEXTURED <br />TEXTURED _ <br />CEMENTICIOUS CEMENTICIOUS 00 <br />FINISH ON C.M.U. FINISH ON C.M.U. Cp <br />(TYP.) (TYP.) <br />-------------------------------------------------I-I----------------J----F.FL. <br />LEFT ELEVATION - Al <br />M <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />..G.C. VERIFY ROOF PITCH" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES" <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />i � III I/qz <br />� ���3���1�t <br />��� <br />O w/v <br />+ef•Na�• <br />o •R' <br />•� F L <br />f a6s'`AQROFE <br />S SRO <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Flodda Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />N <br />W <br />Q <br />$ <br />v E <br />O M N 9k <br />LLLL <br />v <br />0 <br />N 6 Cl <br />� to N N :* LO L, Lu <br />QNMv <br />U- W a <br />� D_ Y <br />ui� <br />� LL� aLLI� <br />0 <br />Z_ <br />7s 1 <br />V S P <br />a.' <br />L N <br />C,4 to m OJ J <br />Nair 0 <br />Z <br />LLW <br />a <br />N M Z X O <br />Z <br />OVCIL v� ai <br />V M � <br />z N <br />o g <br />z � co <br />IM-111111 <br />z <br />J <br />Q_ <br />In <br />z <br />(L) <br />o <br />lL <br />fCi <br />w m <br />m <br />j� <br />OLu <br />N <br />o <br />c i <br />all <br />U � <br />w m <br />8 <br />ji� <br />L <br />= w d <br />c U) <br />¢ Op 0 <br />V m <br />o <br />W <br />� <br />M <br />Z. Q <br />o <br />Z <br />gZ <br />J <br />'� <br />Z. o <br />� <br />o <br />EE O <br />U <br />W <br />Q0 <br />Z® <br />00 <br />o< <br />Z <br />O E <br />N <br />a z <br />a0 <br />¢ <br />d Z <br />ire <br />.4,% L <br />ra <br />o <br />m <br />0 0 <br />OLL <br />z� <br />w <br />d 3 <br />Q <br />0¢ <br />a <br />30 <br />a <br />ww <br />7 % <br />U <br />K2 <br />?0 <br />o <br />1, <br />J <br />00 <br />C� F <br />6 <br />O <br />V <br />Zj< <br />d <br />N O <br />i <br />Lo <br />J <br />L <br />'D^ <br />� <br />0 <br />M <br />00 <br />■ <br />O <br />N <br />� <br />o <br />p <br />'�^ <br />m <br />O <br />T <br />co <br />= N <br />f <br />n O <br />r <br />00 <br />cco j <br />r <br />E <br />L0 <br />C <br />N <br />_4 <br />m <br />Z <br />M <br />Z <br />M <br />E O <br />T <br />�; <br />a <br />E <br />U _ <br />-0 ca p <br />� <br />JOB <br />NO: <br />20-8091 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />