Laserfiche WebLink
1" x 9" SMOOTH <br />TEXTURED <br />FREEZE BAND <br />HEEL <br />T.O.M <br />HDR HGT. <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.0 <br />(TYP.) <br />12 <br />5� <br />8"x8" SMOOTH <br />TEXTURES CORBELS <br />12 <br />3;_7�5 <br />i <br />nrn I nInnnnn <br />12 <br />12 <br />7�5 <br />+3" SMOOTH <br />TEXTURED BAND <br />14'-0" RIDGE VENT <br />FRONT ELEVATION - B1 <br />SCALE: 1/4"=V-0" <br />7'-0" RIDGE VENT <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />12 <br />�5 <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />T.O.M. <br />LEFT ELEVATION - B1 <br />CALE: 1 /4"=V-0" <br />HDR HGT. <br />�— TEXTURED _ o <br />CEMENTICIOUS o? 00 <br />FINISH ON C.M.U. cn <br />(TYP.) <br />— _ F.FL. <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />*i"G.C. VERIFY ROOF PITCH'" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES"* <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. . <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />L <br />C� <br />n <br />i <br />\\�f,4tt468@?9tla <br />0 <br />\O <br />FLO <br />A�OFESSIO`� <br />\ <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained <br />within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />@f <br />W <br />1-o <br />C) <br />E o0 <br />M m <br />S N <br />CN <br />It <br />y <br />7�W, "o <br />cnN0 <br />ik w <br />LL LU d <br />Qai <br />cm v <br />LLa J <br />a <br />Y <br />L <br />t� <br />Z <br />0 <br />o <br />° <br />m N <br />rL O <br />ILW <br />Co <br />a <br />Z <br />N M ZCi <br />pU <br />W D p <br />v � CD <br />Z <br />�1113 <br />V M � <br />],a <br />z N a <br />C,z C, C, <br />z <br />ICM% <br />< <br />-Vda <br />N <br />P7 <br />V) <br />z .1 <br />LL <br />C/i <br />ftS w <br />O <br />w g <br />N w <br />Rig <br />Un <br />U <br />w J <br />_ 2 E <br />I <br />U n in <br />¢ <br />toW <br />2 <br />o <br />Z <br />< <br />E- o <br />g <br />Z® <br />E U <br />I- <br />w0 <br />z <br />x 00 <br />❑ u: <br />so <br />Z <br />CJ E <br />N N <br />a Q <br />¢Z <br />wo <br />�¢❑ <br />¢ <br />ww <br />2) <br />cp <br />m� <br />0 <br />ZZ� <br />CD <br />N � <br />oa <br />a0 <br />W <br />�3 <br />v 3 <br />2 <br />�g <br /><o <br />Nw <br />=K <br />w <br />o- <br />mil <br />O <br />O <br />d <br />zed <br />0 <br />oU 3 <br />O <br />� <br />Ln <br />L <br />� <br />m <br />�11 <br />m <br />� <br />\W <br />.> <br />Nt <br />U <br />� <br />Q <br />C U <br />0 <br />O <br />o <br />C7 <br />Cfl <br />00 <br />r <br />c`0 O <br />O LO <br />0 r <br />L-) <br />r <br />r- <br />m <br />:3T <br />co <br />iri <br />6 <br />Z <br />Z <br />c <br />E 0 <br />ca <br />a <br />U -1 <br />Q p <br />_J <br />JOB <br />NO: <br />20-8083 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />