Laserfiche WebLink
a� <br />v <br />LO <br />0 <br />00 <br />r\ <br />O <br />CD <br />v <br />LO <br />0 <br />J <br />00 <br />0 <br />F' <br />a <br />0 <br />v <br />a <br />E <br />E <br />O <br />2 <br />O <br />C <br />J <br />N <br />N <br />r7 <br />0 <br />U <br />U <br />i <br />a� <br />0 <br />i <br />0 <br />U <br />N <br />LZ <br />0 <br />N <br />5i <br />0 <br />5 <br />CL <br />O <br />a � <br />.o <br />IN <br />12 <br />�5 <br />4, <br />Ell <br />F.FL. <br />W_ia <br />o <br />T-O" TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP. ) <br />FRONT ELEVATION — B1. <br />SCALE: 11/4 _,..o. <br />24'-0" RIDGE VENT <br />T.O.M. <br />HDR HGT. <br />25 SH 25 SH <br />F.FL. <br />.................................................................. L <br />LEFT ELEVATION — 61 <br />1 /4"=1'-0" <br />11 <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved (lashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />�. <br />s <br />S09 <br />b •. 17 <br />CD <br />U 'O. <br />O � <br />UA <br />0, <br />i� <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained <br />within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />N <br />W <br />a <br />lot <br />M 8 <br />� <br />11co <br />N m <br />1A e, <br />® <br />o N <br />, 6 W <br />a0 N <br />ak J <br />J V <br />U LL W <br />h <br />3 <br />COr-n12 <br />M OV <br />.J w a. <br />LL. 2 <br />Qr <br />Ju_" <br />Y <br />a,L� <br />Z <br />rm� <br />C <br />0° <br />�.F,Nco <br />d' O _J <br />co T <br />co <br />a <br />Z <br />LLW <br />N M Z <br />6 U <br />d' N O <br />U J fU <br />Z <br />❑❑❑ <br />W <br />Ur c, <br />1 <br />Z N o <br />z o <br />¢ Q <br />o_ <br />r <br />N <br />M <br />w <br />U <br />Q1)' <br />0 <br />LL <br />'� • <br />T c_j� <br />f>3 ua <br />a <br />m <br />U <br />O <br />Ln <br />c �+ <br />N <br />r— in <br />U c <br />W J <br />a— — E <br />=� <br />L <br />= L N <br />U o °y <br />(2 d <br />¢ N o <br />e <br />�Q <br />�m <br />ti <br />o <br />w <br />M <br />M <br />¢ <br />oF2 <br />z <br />za <br />LJi <br />Q E <br />E a <br />z o <br />o <br />> <br />¢� <br />Ze <br />o� <br />N <br />R.�o <br />�o <br />0 <br />o � <br />O E <br />N R <br />L <br />p <br />ww o <br />d Z <br />- rp <br />C/) _ <br />_ <br />¢ O <br />U <br />y <br />m 0 <br />0¢ <br />Z <br />co J <br />m <br />Q W <br />zz <br />N <br />a <br />o <br />gz <br />a <br />Q <br />Cj <br />ao <br />NW <br />rk <br />Jz <br />�0 <br />O <br />w ¢ <br />zla <br />o 3 <br />0 <br />= Q <br />= <br />> Ln <br />L <br />m <br />E2 <br />^, <br />W <br />m <br />0 <br />p <br />�1 <br />a) <br />N <br />c�1/� <br />CV <br />> <br />O <br />m <br />�OR <br />V <br />/� <br />(0 <br />o <br />r <br />T��� <br />� 6p <br />Lo <br />LO <br />T' <br />i <br />00 <br />T <br />T <br />M <br />E <br />E N <br />co <br />Z <br />Z <br />E O <br />E <br />m <br />o <br />U J <br />Q Q <br />J <br />JOB <br />NO: <br />21-1078 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />T I <br />