Laserfiche WebLink
"0 <br />LO <br />LO <br />8 <br />01 <br />Q-1 I <br />81 <br />E <br />4 <br />=-_3 M <br />12 <br />5F�� <br />TOM I <br />12 <br />zz��5 <br />---------- <br />EXTENDED <br />OVERHANG TO <br />BE CENTERED — <br />ON DOOR <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />------------------ <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP.) <br />14'-0" RIDGE VENT <br />12 <br />J <br />5 15'-0" RIDGE VENT <br />12 <br />1-7: -------- <br />5 <br />I L <br />....................... <br />_' E7�= <br />- - - - - - - - - - <br />- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - --- - - - - - - - - - - - - - - - - - <br />V-00 <br />TEXTURED <br />CEMENTICIOUS <br />01 2'-0" FINISH ON C.M.U. <br />(TYP.) <br />REAR ELEVATION - Al <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />T.O.M. <br />HDR HGT. <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP.) <br />ZD <br />I 1A F.FL. <br />N <br />SCALE: 1/4"=l'-O" <br />LEFT ELEVATION - Al <br />SCALE: 1/4"=l'-O" <br />General Notes <br />ROOF CRITERIA: <br />12" OVERHTNG U.N.O. <br />PLUMB CUT FASCIA ROOF <br />PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH" <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />"ELECTRICAL SPECIFICATION NOTES" <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior plaster. <br />Installation of these materials shall be In compliance with ASTIMC <br />926 and ASTM C 1063. <br />R703.7.1 Lath. <br />All Lath and lath attachments shall be of corrosion -resistant <br />materials. Attached per ASTM C 1063. <br />R703.7.2 Plaster. <br />Plastering w/ portland cement plaster shall be not less than three <br />coats when applied over metal lath or wire lath and shall be not <br />less than two coats when applied over masonry, concrete. <br />R703.7.3 Water -Resistive Baniers. <br />Water -resistive barriers shall be installed where cement plaster <br />(stucco) is to be applied over wood -based sheathing, shall include <br />a water -resistive vapor -permeable barrier. The Individual layers <br />shall be installed independently such that each layer provides a <br />separate continuous plane and any flashing intended to drain to <br />the water -resistive barrier Is directed between the layers. The <br />barriers shall consist of one of the following. <br />1. Two layers of an approved water resistant barrier material in <br />accordance with R703.2. <br />2. One layer of an approved water -resistive barrier (paper <br />backed stucco lath) over an approved synthetic house wrap. <br />R703.4 Flashing. <br />Approved corrosion -resistant flashing shall be applied <br />shingle -fashion in a manner to prevent entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. Flashing shall be Installed at the following locations. <br />Exterior winclowidoor openings. <br />Intersection of chimneys or other masonry constructions with <br />frame wells. <br />Under and at the ends of masonry, wood or metal copings <br />and sills. <br />Continuously above all projecting wood trim. <br />Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />At wall and roof Intersections <br />At Built-in gutters. <br />Attic Ventilation <br />Attic Ventilation to be in compliance with the Florida Building Code 6th Edition <br />(2017) Residential R806. <br />The Minimum net free ventilating area shall be 1/150 of the area of the vented <br />space. The ventilating area may be reduced to 1/300 provided that at least 40% <br />but no more than 50% of the required ventilation is provided in the upper portion of <br />the space to be ventilated.Upper ventilators shall be located no more than 3 feet <br />(measured vertically) below the ridge or highest point of the space, with the <br />balance of the required ventilation provided by eave or cornice vents. <br />-CALCULATIONS BASED ON THE FOLLOWING VALUES, SEE ROOF PLAN** <br />(Values to be verified with Manufacturer Specifications) <br />• RIDGE VENTS 15 SO. IN. OF NET FREE AREA / LINEAR FT. <br />• OFF -RIDGE VENTS 138 SO. IN. OF NET FREE AREA / UNIT <br />e SOFFIT VENTS 7 SO. IN. OF NET FREE AREA I SO. FT. <br />(D <br />2_� <br />0 <br />ClLn <br />LU <br />0 LU <br />V) <br />U <br />LU <br />C14 <br />C" <br />U <br />01- <br /><1 <br />01 o <br />Al I <br />WFD. <br />N C. '7 <br />3 z <br />CHOM <br />U) E <br />LL;3 44 It - <br />z JT <br />LU 4C <br />,it U F. <br />_"4-Q". M <br />SE r <br />'0 <br />0 <br />F <br />1"ROFES5\0 <br />To the best of the Engineers knowledge, information and belief. <br />the structural plans and specifications contained within these <br />drawings comply with the 2017 Florida Building Code - <br />Residential 6th EdItIon. Engineer's signature and seal Is only for <br />the structure[ engineering portions of the drawing pages bearing <br />Englneees signature and seat. <br />LENNAR <br />4600 W. Cypress St, Suite 200 1 Tampa, FL 33607 <br />www.LennarTampa.com <br />5 <br />I­z <br />U) <br />4—;- <br />a: <br />0 <br />00000FAIN <br />L.0 <br />U kl� 0 <br />UJ <br />L -U <br />t <br />z <br />11%� <br />U) <br />0 <br />z <br />CE: <br />LU <br />r- P <br />C'J <br />Z <br />z <br />LU <br />_J <br />Lr) <br />z <br />U <br />06 <br />ZZ <br />:5 <br />t7u <br />UJ <br />0 <br />rn <br />T.-W! <br />Ln <br />SCALE AS NOTED <br />DATE 10/2/2018 <br />TECH: MIAMES <br />VERSION NO - 4mO <br />SHEET NO. <br />3.2 <br />