Laserfiche WebLink
FLASHING REQUIREMENTS <br />R609.1 General. This section prescribes performance and construction requirements for exterior <br />windows and doors installed in walls. Windows and doors shall be installed and flashed in accordance <br />with the fenestration manufacturer's written instructions. Window and door openings shall be flashed <br />in accordance with Section R703.4. Written installation instructions shall be provided by the <br />fenestration manufacturer for each window or door. <br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved water -resistive barrier shall be applied <br />over studs or sheathing of all exterior walls. Such felt or material shall be applied horizontally, with the <br />upper layer lapped over the lower layer not less than 2 Inches (51 mm). Where joints occur, felt shall <br />be lapped not less than 6 inches (152 mm). The felt or other approved material shall be continuous to <br />the top of walls and terminated at penetrations and building appendages in a manner to meet <br />the requirements of the exterior wall envelope as described in Section R703.1. The water -resistive <br />barrier is not required for detached accessory buildings. <br />R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner <br />to prevent entry of water Into the wall cavity or penetration of water to the building structural framing <br />components. Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior <br />fenestration products shall be sealed at the juncture with the building wall with a sealant complying <br />with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and <br />contraction, ASTM C1281, AAMA 812, or other approved standard as appropriate for the type of <br />sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The <br />flashing shall extend to the surface of the exterior wall finish. Approved corrosion resistant flashings <br />shall be installed at the following locations: <br />CUT HOUSEWRAP AT <br />450 ANGLE <br />MODIFIED "I" CUT IN <br />HOUSEWRAP <br />LINE OF WINDOW <br />OPENING <br />APPROVED HOUSEWRAP OVER - <br />SHEATHING OVER WD STUD WALL <br />STEP I <br />INSTALL 4" WIDE <br />SELF -ADHERING <br />STRAIGHT FLASHIP <br />OVER NAILING FLA <br />AT IAMBS <br />EXTEND FLASHING <br />BELOW SILL FLEXII <br />FLASHING & MIN 2 <br />THE HEAD <br />'t <br />17" <br />TEMPORARILY <br />FOLD -UP & SE( <br />HOUSEWRAP (I <br />TUCK FLAP LIN <br />AT HEAD <br />FOLD HOUSE <br />IN AT IAMBS <br />SLOPE SILL P <br />1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to <br />the surface of the exterior wall finish or to the water -resistive barrier complying with Section 703.2 for <br />subsequent drainage. Mechanically attached flexible flashings shall comply with AAMA 712. Flashing at <br />exterior window and door openings shall be installed in accordance with one or more of the following: <br />1. 1.1.The fenestration manufacturer's installation and flashing instructions, or for applications not <br />addressed in the fenestration manufacturers instructions, in accordance with the flashing <br />manufacturers instructions. Where flashing instructions or details are not provided, pan flashing shall <br />be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or sloped in <br />such a manner as to direct water to the surface of the exterior wall finish or to the water resistive <br />barrier for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection <br />at the head and sides. <br />2. 1.2.In accordance with the flashing design or method of a registered design professional. <br />3. 1.3.In accordance with other approved methods. <br />4. 1.4.In accordance with FMA/AAMA 100, FMAJ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA <br />300 or FMIA/AAMA/WDMA 400. <br />2. 2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with <br />projecting lips on both sides under stucco copings. <br />3. 3.Under and at the ends of masonry, wood or metal copings and sills. <br />4. 4.Continuously above all projecting wood trim. <br />5. 5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame <br />construction. <br />6. 6.At wall and roof intersections. <br />7. 7.At built-in gutters. <br />INSTALL 4" - <br />SELF -ADHERING <br />FLASHING OVER <br />WINDOW FIN HEAD <br />EXTEND SELF -ADHERING --J <br />FLASHING 1" MIN BEYOND <br />JAMB FLASHING I <br />STEP 7 <br />TYPICAL WINDOW FLASHING INSTALLATION DETAILS <br />ill <br />MIN <br />NLIGN FLASHIN( <br />NI INT. EDGE 0 <br />3ILL R.O. <br />1ECHANICALLY <br />:ASTEN FANNEE <br />:_DGES. (CAP NA <br />,TAPLES) PER M <br />:NSTRUC-nONS <br />:NSTALL 6" WID <br />3ELF-ADHERING <br />:LASHING AT SI <br />:XTEND FLEX FL <br />)OWN THE SILL <br />FOLD HOUSEWRAP <br />DOWN.CONSTRUCTI <br />TAPE ACROSS HEAD <br />WINDOW & THEN <br />DIAGONAL CUT <br />A. CONTINUOUS <br />) BACK OF WIND <br />;E IN LINE W/ <br />IOLES OR SLOTE <br />INSTALL WINE <br />PLUMB, LEVEL <br />SQUARE PER I'l <br />WRITTEN INS' <br />NOTE: <br />1. WINDOW INSTALLATION AND FLASHING DETAILS ARE CONSISTENT <br />WITH ASTM E 2112 METHOD A-1 EXCEPT SELF -ADHERING <br />FLASHINGS ARE USED <br />2. IT IS THE CONTRACTORS RESPONSIBILITY TO VERIFY THE <br />COMPATIBILITY OF ALL PRODUCTS INCLUDING HOUSEWRAP, <br />SEALANTS & SELF -ADHERING FLASHING MATERIALS USED DURING <br />CONSTRUCTION. <br />3. INSTALL ALL MATERIALS PER MANUFACTURER!S WRITTEN <br />SPECIFICATIONS <br />WARNING: SEALANTS/FLASHINGS MAY REACT ADVERSELY IF NOT <br />COMPATIBLE. <br />NOTE: <br />TYPICAL WINDOW & DOOR FLASHING <br />INSTALLATION DETAILS PREPARED IN <br />ACCORDANCE WITH FBC APPROVED <br />SPECIFICATIONS. <br />SEAL WIND <br />SEAL WINDOW FRAME TO <br />INSIDE OF R.O. W/ SEALANT AT <br />INSIDE OF <br />SILL AND A <br />SILL AND A MIN 6" UP BOTH <br />IAMBS To, <br />IAMBS TO FORM A BACK DAM. <br />SEAL BALM <br />SEAL BALANCE OF FRAME WITH <br />SEALANT OR NON -EXPANDING <br />SEALAN _ r 0 <br />FOAM (PRO <br />FOAM (PROVIDE BACKER ROD <br />WHERE REQUIRED) <br />SELF -ADHERING FLEXIBLE <br />X" �5�FLASHING AT SILL, FLUSH <br />'TO INTERIOR FRAMING. <br />INTERIOR VIEW <br />STEP 9 <br />NTS <br />DAVIS BEWS <br />DESIGN GROW <br />L50 STATE STR= EAST <br />OUD&ML, FWRMA 34677 <br />813. 925.1300 Tr=L <br />813. 925. 1800 FAX <br />VVWWDAVLSBEWS.00M <br />T,*.�A * OlE7,4� <br />EST. 1994 <br />rsl <br />0 <br />k-0 <br />Z> V) M <br />(0 Ln <br />Z CL <br />�2 U1 <br />U_ <br />CL <br />U CL 00 <br />Z < E <br />Z <br />W z <br />UJ <br />_J <br />0, <br />�R <br />LLJ <br />Z g <br />Z Z <br />g <br />UZ00 <br />U L) <br />Z LU <br />.J 21 <br />Z <br />Z <br />Q 0 _J LLJ <br />< � S,� 6 -,,,1 <br />CL LLI W 8 <br />0 W LL <br />U UJ 04 <br />00 Z <br />UJ <br />0 <br />Z Z <br />Z Z <br />Z <br />0 <br />0 <br />U <br />b <br />D 0 Z <br />U-1 <br />LJJ <br />Z C:) <br />0 < N LU <br />Z _, C) <br />Z Z 0 <br />LU U Z 0 U <br />UJ Z (D <br />Z 0 Z <br />< <br />Z LU a <br />ca Z <br />0 4� �_ D <br />0- IJ.J %D M <br />SCALE AS NOTED <br />DATE 10-19-2018 <br />VERSION NO. <br />100 <br />SHEEr NO. <br />DT5n 1 <br />