|
OPTIONAL OVERHEAD SERVICE SAME AS
<br />UNDERGROUND 150 OR 200 AMP SERVICE
<br />REFER TO FLOOR PLAN FOR
<br />NOTED AMPS, REQUIRED
<br />UNDERGROUND SERVICE
<br />BY POWER COMPANY
<br />150 = »I COPPER OR 2/0 ALUMINUM
<br />200 = 2/0 COPPER OR 4/0 ALUMINUM IN 2" CONDUIT.
<br />"12 COPPER TO APPLIANCES AND GFI
<br />14 COPPER TO LIGHTS AND OUTLETS
<br />MO COPPER TO WATER HEATER
<br />18 COPPER TO RANGE
<br />06 COPPER TO HVAC
<br />TOP RAILING
<br />NOTE: SUBFLOOR ADHESIVE IS USED IN ADDITION
<br />BALUSTERS TO NAILS ON WOOD COMPONENTS,
<br />MAX SPACING 4"
<br />1 X 8 PAINTED IUD. CAP STRINGER IS LAMINATED TO A THICKNESS EQUIVALENT TO
<br />OGEE STOP THE SIZE OF A 2 X 12 S.Y.P. AND IS NAILED TO EACH
<br />TREAD W/ 16d NAILS FROM THIRD LAMINATE TO TREAD-
<br />OPT, 2 X 2 BLOCKING NAILED
<br />TO TREAD AND RISER,
<br />04 GROUNDING WIRE WITH CODE I
<br />APPROVED CLAMP PER 250.50 17
<br />3-2 X 12 STRINGER 2 X BLOCKING NAILED TO STRINGER,
<br />AND 250.52 OF THE 2014 NEC. ]][�� � o
<br />M 3/4" RISERS RISER, AND TREAD.
<br />INTERSYSTEM BONDING TERMINATION PER NEC 08, 250.94
<br />ELECTRICAL RISER DIAGRAM -
<br />NOTE:
<br />ELECTRICAL MATERIALS AND INSTALLATIONS SHALL COMPLY W/ APPLICABLE PROVISIONS
<br />OF THE NFPA 10-08, LOCAL CODES AND LOCAL POWER/`UTILITY COMPANY
<br />5TAIR NOTE5
<br />RAILING
<br />BALUSTERS SHALL BE SPACED SO THAT A 4" SPHERE CANNOT PA55 THROUGH.
<br />HANDRAILS
<br />HANDRAILS FOR STAIRWAYS SHALL BE CONTINUOUS FOR THE FULL LENGTH OF THE FLIGHT, FROM A POINT DIRECTLY ABOVE THE TOP RISER OF
<br />THE FLIGHT TO A POINT DIRECTLY ABOVE THE LOWEST RISER HANDRAIL ENDS SHALL BE RETURNED OR SHALL TERMINATE IN NEWEL POSTS OR
<br />SAFETY TERMINALS. HANDRAILS ADJACENT TO A WALL SHALL HAVE A SPACE OF NOT LESS THAN 1-1/2 INCH BETWEEN THE WALL AND HANDRAILS.
<br />CONTINUOUS GRASPABLE HANDRAIL MUST MEET TYPE ONE OR TYPE TWO CRITERIA
<br />UNDER -STAIR PROTECTION
<br />ENCLOSED ACCE551BLE SPACE UNDER STAIRS SHALL HAVE WALLS, UNDER -STAIR SURFACE AND ANY SOFFIT PROTECTED ON THE
<br />ENCLOSED SIDE W/ 1/2 INCH GYPSUM BOARD PER F.B.C. RESIDENTIAL 6th EDITION (2011) - R302.1 AND R302.11
<br />5TAIRWALL FRAME NOTE
<br />ALL STAIRWELL SURROUNDING WALLS AND KNEE WALLS ARE TO BE FRAMED AT 16" O.C. TO PROTECT FROM FALLING HAZARD
<br />OCCUPANCY AND CON5TRUCTION TYPE:
<br />THIS UNIT HAS AN R3 OCCUPANCY AND BUILDING TYPE V-B CLASSIFICATION.
<br />CEILING CONSTRUCTION:
<br />I. THE GARAGE SHALL BE SEPARATED FROM THE RESIDENCE AND ITS ATTIC AREA BY NOT LESS THAN 1/2 INCH (12.1 mm) GYPSUM BOARD APPLIED
<br />TO THE GARAGE SIDE, GARAGES BENEATH HABITABLE ROOMS SHALL BE SEPARATED FROM ALL HA ITABLE ROOMS ABOVE BY NOT LESS THAN
<br />5/8 INCH (15.9 mm) TYPE "X" GYPSUM BOARD OR EQUIVALENT, WHERE THE SEPARATION IS A FLOOR -CEILING ASSEMBLY, THE STRUCTURE
<br />SUPPORTING THE SEPARATION SHALL AL50 BE PROTECTED BY NOT LESS THAN 1/2 INCH (12.1 mm) GYPSUM BOARD OR EQUIVALENT.
<br />DWELLING / GARAGE OPENING5:
<br />I. THE OPENING BETWEEN THE GARAGE AND LIVING AREA SHALL BE EQUIPPED WITH 50LID WOOD DOORS NOT LESS THAN 1 3/8" IN THICKNESS,
<br />SOLID CORE (S.C.) OR HONEYCOMB CORE STEEL DOORS NOT LE55 THAN 1 3/5" THICK, OR 20 MINUTE FIRE RATED DOORS,
<br />2, ALL DOORS FROM GARAGE ADJACENT TO LIVING SPACE MUST BE EITHER A 50LID CORE DOOR OR HAVE A MIN. FIRE RATING OF 20 MINUTES.
<br />EGRE55:
<br />EACH BEDROOM MUST HAVE ONE WINDOW THAT COMPLIES WITH EGRE55 CODES, IF THERE 15 NO ACCESS TO EXTERIOR THROUGH A DOOR. THE
<br />WINDOW MUST HAVE A MAXIMUM OPENING HEIGHT OF 44" ABOVE FINISH FLOOR LINE OF THAT PARTICULAR ROOM,
<br />WINDOW IN5TALLATION:
<br />WINDOWS SHALL BE INSTALLED AND FLASHED IN ACCORDANCE WITH THE MANUFACTURERS WRITTEN INSTALLATION INSTRUCTIONS. WRITTEN
<br />INSTALLATION INSTRUCTIONS SHALL BE PROVIDED BY THE MANUFACTURER FOR EACH WINDOW.
<br />TERMITE PROTECTION:
<br />I. PENETRATION. PROTECTIVE SLEEVES AROUND PIPING PENETRATING CONCRETE SLAB -ON -GRADE FLOORS SHALL NOT BE OF CELLULOSE
<br />CONTAINING MATERIALS. IF SOIL TREATMENT 15 USED FOR SUBTERRANEAN TERMITE PROTECTION, THE SLEEVE SHALL HAVE A MAXIMUM WALL
<br />THICKNE55 OF 0.010 INCH, AND BE SEALED WITHIN THE SLAB USING A NON -CORROSIVE CLAMPING DEVICE TO ELIMINATE THE ANNULAR SPACE
<br />BETWEEN THE PIPE AND THE SLEEVE. NO TERMITICIDE5 SHALL BE APPLIED INSIDE THE SLEEVE.
<br />2. PROTECTION AGAINST DECAY AND TERMITES. - CONDENSATE LINES, IRRIGATION / SPRINKLER SYSTEM RISERS FOR SPRAY HEADS, AND ROOF
<br />DOWNSPOUTS SHALL DISCHARGE AT LEAST I FOOT (305 mm) AWAY FROM THE STRUCTURE 51DEWALL, WHETHER BY UNDERGROUND PIPING, TAIL
<br />EXTENSIONS, OR SPLASH BLOCKS. GUTTERS WITH DOWN5POUT5 ARE REQUIRED ON ALL BUILDINGS WITH EAVES OF LESS THAN 6 INCHES (152 mm)
<br />HORIZONTAL PROJECTION EXCEPT FOR GABLE END RAKES OR ON A ROOF ABOVE ANOTHER ROOF.
<br />2 X TREADS± RIP FROM 2x12
<br />TO SIZE NOTED ON PLAN
<br />TYP. OPT. RAILING ELEVATION
<br />SCALE: 1/2" = 1411
<br />NEWEL P05T
<br />TOP RAILING
<br />BALUSTER 4" O.C.
<br />SHOE RAIL (REMOVE
<br />W/ METAL SPINDLES)
<br />I X 8 PAINTED WD. CAP
<br />OGEE STOP
<br />r QUK LINt _
<br />OPTIONAL
<br />,, RAILING DETAIL
<br />SCALE. I - I 0
<br />I X SPRUCE "3 OR 3/4" CDX.
<br />PLYWD, RISER.
<br />2 X SOUTHERN YELLOW PINE $1
<br />(ACTUAL THICKNESS IS 1 1/2") TREAD,
<br />CLOSED RISER DETAIL
<br />SCALE: 1/2" = 1'-0"
<br />CARP[
<br />CARP[
<br />TREAC
<br />RISER
<br />2X4WALL
<br />1/2" GYP BD.
<br />3/4" SKIRT BD.
<br />2 X 4 SPACER
<br />2X12
<br />STRINGER
<br />TYPICAL STAIR
<br />FRAMING DETAIL
<br />B SCALE: 3/4" : I4"
<br />GENERAL CONSTRUCTION NOTES
<br />CHAPTERS AND SECTIONS REFER TO F.B.C. RESIDENTIAL 6th EDITION (2011)
<br />MECHANICAL AND HVAC:
<br />I. ENERGY CALCULATIONS FOR HEATING AND COOLING CAPACITIES SHALL BE FURNISHED BY THE GENERAL CONTRACTOR AS AN ATTACHMENT TO
<br />TH15 PLAN SET AT THE TIME OF APPLICATION FOR PERMIT.
<br />2. MECHANICAL APPLIANCES SHALL BE ACCESSIBLE FOR INSPECTION, SERVICE, REPAIR, AND REPLACEMENT WITHOUT REMOVING PERMANENT
<br />CONSTRUCTION, OTHER APPLIANCES, OR ANY OTHER PIPING OR DUCTS NOT CONNECTED TO THE APPLIANCE BEING INSPECTED, SERVICED,
<br />REPAIRED, OR REPLACED. A LEVEL WORKING SPACE AT LEAST 30 INCHES (162 mm) DEEP AND 30 INCHES (162 mm) WIDE SHALL BE PROVIDED IN
<br />FRONT OF THE CONTROL SIDE TO SERVICE AN APPLIANCE.
<br />3. DUCTS IN THE GARAGE AND DUCTS PENETRATING THE WALLS OR CEILINGS SEPARATING THE DWELLING FROM THE GARAGE SHALL BE
<br />CONSTRUCTED OF A MIN. "26 GAUGE (0,48 mm) SHEET STEEL OR OTHER APPROVED MATERIAL AND SHALL HAVE NO OPENINGS INTO THE GARAGE.
<br />4. FOUNDATIONS AND SUPPORTS FOR OUTDOOR MECHANICAL SYSTEMS SHALL BE RAISED AT LEAST 3 INCHES (1(o mm) ABOVE THE FINISHED
<br />GRADE AND SHALL ALSO CONFORM TO THE MANUFACTURER'S INSTALLATION INSTRUCTIONS.
<br />5. AUXILIARY DRAIN PAN. CATEGORY IV CONDENSING APPLIANCES SHALL BE PROVIDED WITH AN AUXILIARY DRAIN PAN WHERE DAMAGE TO
<br />ANY BUILDING COMPONENT WILL OCCUR AS A RESULT OF STOPPAGE IN THE CONDENSATE DRAIN PIPING SYSTEM. THESE PANS SHALL BE
<br />INSTALLED IN ACCORDANCE WITH THE APPLICABLE PROVISIONS OF 5ECTION5 M14113,
<br />EXHAU5T FAN5 AND VENTING
<br />1.OUTDOOR DISCHARGE. THE AIR REMOVED BY EVERY MECHANICAL EXHAUST SYSTEM SHALL BE DISCHARGED TO THE OUTDOORS. AIR SHALL
<br />NOT BE EXHAUSTED INTO AN ATTIC, SOFFIT, RIDGE VENT OR CRAWL SPACE.
<br />2. EXHAUST AIR FROM BATH ROOMS AND TOILET ROOMS SHALL NOT BE RECIRCULATED WITHIN A RESIDENCE OR TO ANOTHER DWELLING UNIT AND
<br />SHALL BE EXHAUSTED DIRECTLY TO THE OUTDOORS. EXHAUST AIR FROM BATHROOMS AND TOILET ROOMS SHALL NOT DISCHARGE INTO AN ATTIC,
<br />CRAWL SPACE, OR OTHER AREAS INSIDE THE BUILDING,
<br />3. DUCT LENGTH. THE MAXIMUM LENGTH OF A CLOTHES DRYER EXHAUST DUCT SHALL NOT EXCEED 25 FEET FROM THE DRYER LOCATION TO THE
<br />WALL OR ROOF TERMINATION. THE MAXIMUM LENGTH OF THE DUCT SHALL BE REDUCED 2.5 FEET (162 mm) FOR EACH 45 DEGREE (0.19 RAID) BEND
<br />AND 5 FEET (1524 mm) FOR EACH 90 DEGREE (Ilo RAD) BEND, THE MAXIMUM LENGTH OF THE EXHAUST DUCT DOES NOT INCLUDE THE TRANSITION
<br />DUCT.
<br />EXCEPTION - WHERE A CLOTHES DRYER BOOSTER FAN 15 INSTALLED AND LISTED AND LABELED FOR THE APPLICATION, THE MAXIMUM LENGTH OF
<br />THE EXHAUST DUCT, INCLUDING ANY TRANSITION DUCT, SHALL BE PERMITTED TO BE IN ACCORDANCE WITH THE BOOSTER FAN MANUFACTURER'S
<br />INSTALLATION INSTRUCTIONS. WHERE A CLOTHES DRYER BOOSTER FAN 15 INSTALLED AND NOT READILY ACCESSIBLE FROM THE ROOM IN WHICH
<br />THE DRYER 15 LOCATED, A PERMANENT IDENTIFYING LABEL SHALL BE PLACED ADJACENT TO WHERE THE EXHAUST DUCT ENTERS THE WALL. THE
<br />LABEL SHALL BEAR THE WORDS "TH15 DRYER EXHAUST SYSTEM 15 EQUIPPED WITH A REMOTELY LOCATED BOOSTER FAN."
<br />4. PROVIDE LOUVER DEVICES AT INTAKE AND EXHAUST LOCATIONS IN ACCORDANCE WITH
<br />AMIGA STANDARD 550 IN FBC.
<br />ROUGH- IN INSPECTION REQUE5T NOTE
<br />ALL PLUMBING, ELECTRICAL AND MECHANICAL ROUGH -INS MUST BE
<br />COMPLETE, INSPECTED AND APPROVED BEFORE REQUESTING THE
<br />FRAMING INSPECTION.
<br />WINDOW FALL PROTECTION
<br />IN DWELLING UNITS, WHERE THE OPENING OF AN OPERABLE WINDOW IS
<br />LOCATED MORE THAN 12 INCHES ABOVE THE FINISHED GRADE OR
<br />SURFACE BELOW, THE LOUDEST PART OF THE CLEAR OPENING OF THE
<br />WINDOW SHALL BE A MINIMUM OF 24 INCHES ABOVE THE FINISHED
<br />FLOOR OF THE ROOM IN WHICH THE WINDOW IS LOCATED, OPERABLE
<br />SECTIONS OF WINDOWS SHALL NOT PERMIT OPENINGS THAT ALLOW
<br />PASSAGE OF A 4 INCH DIAMETER SPHERE WHERE SUCH OPENINGS
<br />ARE LOCATED WITHIN 24 INCHES OF THE FINISHED FLOOR PER F.B.C.
<br />RESIDENTIAL 6th EDITION (2011) - SECTION R312.2.
<br />WINDOW FALL PREVENTION DEVICES AND WINDOW GUARDS, WHERE
<br />PROVIDED, SHALL COMPLY WITH THE REQUIREMENTS OF ASTM F 2090
<br />PER F.B.C. RESIDENTIAL bth EDITION (2011) - SECTION R312.2.
<br />IN5ULATION NOTE5
<br />• CMU WALLS:----- R-FOIL 4.1 • KNEE WALLS THAT
<br />BACK UP TO CEILING
<br />• FRAME WALLS:-------- R-13 AREA ONLY:----------- R-19
<br />• CEILING:------------- R-30
<br />ON51TE FOUNDATION 5URVEY NOTE
<br />A FOUNDATION SURVEY SHALL BE PERFORMED AND A COPY OF THE
<br />SURVEY SHALL BE ON THE 51TE FOR THE BUILDING INSPECTOR'S USE,
<br />OR ALL PROPERTY MARKERS SHALL BE EXP05ED AND A STRING
<br />5TRECHED FROM MARKER TO MARKER TO VERIFY REQUIRED
<br />SETBACKS.
<br />CELING AT ENTRY NOTE
<br />ALL ENTRY CLGS. TO BE 15/32 05B. CEMENTITOUS FINISH (UN.0)
<br />G45 APPLIANCE PROTECTION IN GARAGE NOTE
<br />PROTECTION OF GAS APPLIANCES IN RESIDENTIAL GARAGES:
<br />MINIMUM 3" DIAMETER SCH 40 STEEL PIPE, 2 FT. BELOW CONCRETE
<br />SLAB AND 3 FT. ABOVE FINISHED FLOOR.
<br />GENERAL NOTE5
<br />• DUE TO VARIATIONS IN CITY REQUIREMENTS, SUBDIVISION
<br />SPECIFICATIONS, CONSTRUCTION TECHNIQUES, DIVERSITY IN
<br />MATERIALS, AND PLAN REVISIONS, ALL DIMENSIONS AND
<br />ELEVATIONS MAY VARY PER INDIVIDUAL PLAN, ACTUAL FIELD
<br />CONDITIONS MAY VARY AND MUST BE VERIFIED BEFORE
<br />PROCEEDING WITH CONSTRUCTION.
<br />• ELECTRICAL LOCATIONS SHOWN ON DRAWINGS MAY BE CHANGED
<br />AT THE SOLE DISCRETION OF CALATLANTIC HOMES OR ITS
<br />LICENSED ELECTRICIAN IN ORDER TO COMPLY W/ NATIONAL AND
<br />MUNICIPAL BUILDING AND ELECTRICAL CODES. CALATLANTIC
<br />HOMES WILL NOT GUARANTEE LOCATION OR QUANTITY OF OUTLETS
<br />AND / OR SWITCHES SHOWN.
<br />• ALL PLUMBING DIMENSIONS ARE APPROXIMATE FROM THE CENTER
<br />LINE OF THE FIXTURE TO THE EXTERIOR SLAB EDGE. IT IS THE
<br />RESPONSIBILITY OF THE PLUMBER TO VERIFY THE ACCURACY OF
<br />ALL PLUMBING DIMENSIONS.
<br />NOTE: ANY DIMENSIONS AND/OR CALLOUT5 WITHIN TH15 SET OF DRAWINGS REFERENCING
<br />LUMBER SIZES OR WALL THICKNESSES ARE TO BE CONSIDERED "NOMINAL DIMENSIONS"
<br />CHIMNEY HEIGHT REQUIREMENT5:
<br />WHEN STANDARD OR OPTIONAL FIREPLACE IS TO BE INSTALLED THE CHIMNEY MUST EXTEND Y-0" PAST THE HIGHER POINT WHERE IT
<br />EXTENDS THROUGH THE ROOF AND MUST BE 2'-0" HIGHER THAN THE ROOF OR RIDGE THAT 15 10'-0" AWAY OR CLOSER.
<br />TUB AND SHOWER AREA5:
<br />CEMENT, FIBER -CEMENT, OR GLA55 MAT GYPSUM BOARD (NO GREEN BOARD ALLOWED) IN COMPLIANCE WITH ASTM C1286, GI325, OR CI118
<br />AND INSTALLED IN ACCORDANCE WITH MANUFACTURER RECOMMENDATIONS SHALL BE USED AS BACKERS FOR WALL TILE IN TUB AND
<br />SHOWER AREAS, AND WALL PANELS IN SHOWER AREAS.
<br />FLOOD ZONE REQUIREMENT5:
<br />PLAN MEETS OR EXCEEDS FEMA FLOOD FINISHED GARAGE FLOOR ELEVATION,
<br />DAVIS BEWS
<br />DESIGN GROUP
<br />�.so sr�`rE STREET Fi�.sr
<br />of os�n�, r�.oRro� a��n
<br />813 . 925 . L300 TFL
<br />813. was . isoo FAX
<br />W W W.D.'�VISBEWS.COM
<br />TAMPA • DELAYER.
<br />-�=� FST.1994 �ti-�--
<br />0
<br />Z N
<br />O °r o
<br />� M O
<br />j M Ln
<br />gQoLn
<br />Q a�
<br />M
<br />z < E
<br />U o- 00
<br />Z��`.
<br />w
<br />wo
<br />J o
<br />�o
<br />�o
<br />w�
<br />z0.
<br />Q�
<br />'^ OQQ,o
<br />�zz
<br />I-1 o W z
<br />J
<br />OLu
<br />celLL0
<br />W o�
<br />0 zo
<br />av
<br />r zZ
<br />z Z
<br />O Q
<br />H
<br />Z
<br />oQ
<br />.~� UJ
<br />z Q�W
<br />z
<br />z U z zo
<br />J 0
<br />Lu z I z
<br />0
<br />z a L 0
<br />co z
<br />° g w �m
<br />SCALE : AS NOTED
<br />DATE : 10-19-2018
<br />VERSION NO.
<br />iso
<br />SHEET NO.
<br />DT1
<br />
|