Laserfiche WebLink
COLUMN CON5TRUC <br />STUCCO <br />(CEMENT PLASTER) <br />LATH- <br />2 LAYERS WRB---- It <br />WEEP SCREED �F, <br />CONCRETE STOOP <br />1 COLUMN AT CONCRETE SLAB <br />SCALE: N.I.S. <br />= l:2 <br />FLASHING <br />NAILING FII <br />NO 5EALA <br />NOTE: <br />MAKE SURE THE SHEATHING WRAP LAPS OVER THE TOP <br />FIN. LEAVE A I/4" GAP BETWEEN THE EXTERIOR FINISH <br />AND THE FLANGE, BUT DON'T CAULK THIS GAP. WATER <br />DRAINING FROM ABOVE MUST HAVE A PLACE TO EXIT. <br />6 FIN WINDOW HEAD DETAIL <br />SCALE: N.T.S. <br />CORNER BEAD FASTENED WITH <br />NAILS, SCREWS, OR STAPLES AT <br />t II^/- \/rMTIP AI Iv <br />STUCCO <br />OUTSIDE CORNER <br />WIRE LA <br />CEMENT PLASTER <br />(STUCCO) <br />INSIDE CORNER <br />2 STUCCO DETAIL AT CORNERS <br />SCALE: N.T.S. <br />BEAD OF 51LICON <br />CAULK UNDER <br />WINDOW FLANGE <br />SEALANT <br />BITUMINOUS <br />MEMBRANE OR FELT <br />STUCCO BAND <br />EXTERIOR FINISH <br />SILL DETAIL <br />7 FIN WINDOWS EXT. CASINGS <br />SCALE: M.S. <br />HEADER DETAIL <br />BACK CAULK SILL DAM <br />AND 12" UP WALL EACH SIDE <br />STOP FLASHING HERE INTERIOR <br />PEEL -AND -STICK <br />MEMBRANE <br />2LAYERS <br />W.R.B. <br />SHEATHING <br />NOTES: <br />APPLY A NARROW DAM STRIP TO THE ROUGH SILL BEFORE FLASHING WITH <br />SHEATHING WRAP OR A FLEXIBLE FLASHING MEMBRANE <br />3 SILL FLASHING DETAILS <br />1 SCALE: N.T.5. <br />EXTERIOR FIN15H <br />STUCCO BAND <br />BITUMINOUS <br />MEMBRANE OR FELT <br />STEP 1 <br />INSTALL THE VENT ACCORDING TO THE <br />MANUFACTURER'S RECOMMENDATIONS. TRIM <br />THE HOUSE WRAP A CL05E AS P0551BLE <br />AROUND THE PERIMETER OF THE VENT. <br />SELF ADHESIVE <br />MEMBRANE FLASHING <br />AT DOORS <br />BACK CAULK SILL <br />AND 12" UP WALL <br />EACH SIDE <br />WOOD FRAME <br />4 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />STEP 2 <br />FLASH THE VENT U51NG THE SAME METHOD AS WINDOWS. STARTING AT <br />THE BOTTOM FLANGE: CUT THE FLASHING SO THAT IT EXTENDS PAST <br />THE FLANGES BY I" ON BOTH SIDES. NOW APPLY THE FLASHING TO <br />THE SIDES OF THE VENT, REMEMBER TO EXTEND THE FLASHING I" ON <br />BOTH TOP AND BOTTOM. MAKE SURE TO SMOOTH OUT WRINKLES AND <br />AIR BUBBLES. THE USE OF A J-ROLLER IS OPTIONAL. <br />PREFAB METAL DOOR THRESHOLD � I DOOR TOR <br />FORMED "SEAT" IN <br />CONCRETE SLAB ACTS <br />AS PAN FLASHING <br />• SLAB ON GRADE e USE <br />° °� PLASTIC <br />SHIMS <br />CONCRETE SLAB DOOR <br />5 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />NOTE: <br />THI5 TYPE OF INSTALLATION 15 SUITABLE FOR SEVERAL DIFFERENT PENETRATIONS. ALWAYS <br />USE THE SHINGLING METHOD AND ENSURE A TIGHT SEAL AROUND THE FLANGE/PENETRATION. <br />8 FRAME WALL FLASHING PENETRATIONS <br />SCALE: N.T.S. <br />STEP 3 <br />THE FINAL STEP IS TO INSTALL THE <br />FLASHING ACRO55 THE TOP. EXTEND THE <br />FLASHING OUT AT LEAST I" ON BOTH SIDES. <br />DAMS BEWS <br />DESIGN GROUP <br />150 STATE STREET EAST <br />OLDfiMAR, FLORmA 346T7 <br />813. 925. L300 TEL <br />813.9'1.5.1800 FAX <br />W W WDAVLSBEWS.CAM <br />TAMPA • DIIWER.. <br />- —�� EST. <br />L I <br />e <br />O <br />Z � <br />0 0) <br />M:u CD <br />� M O <br />M <br />(% M II <br />2L�0Ln <br />co <br />Q fl. <br />Q U Q00 <br />Z <br />w Wo <br />J CD <br />�o <br />W� <br />za <br />�a <br />Wawa <br />,^ Uzce0 <br />�JJ �CK <br />J ZQ <br />F--� w Z <br />a �aLH <br />0� <br />8 W cz LL N <br />W off© <br />0 8 <br />z z <br />r <br />O Q Q <br />D Z <br />W <br />LLL 0 <br />�Lu <br />Q Z Q N W <br />Z <br />Lu <br />z U z zo <br />OU <br />� p 0 Z <br />z Q W 0 <br />rn W �m <br />SCALE : AS NOTED <br />DATE : 10-19-2018 <br />VERSION NO. <br />loo <br />SHEET NO. <br />DT4 <br />