|
FLASHING REQUIREMENTS
<br />WEATHER RESISTIVE
<br />FLASHING AND SEALANTS FOR EXTERIOR WINDOW AND DOOR OPENINGS SHALL COMPLY WITH
<br />BARRIER
<br />WINDOW UNIT
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW
<br />SECTION R703.4.
<br />_
<br />DOOR ROUGH OPENING
<br />-=
<br />SLOPE
<br />GENERAL FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />R703.2 WATER -RESISTIVE BARRIER. ONE LAYER OF NO.15 ASPHALT FELT, FREE FROM HOLES AND
<br />-
<br />WOOD FRAME " a ;`
<br />0.3 in: 12.0 in
<br />BREAKS, COMPLYING WITH ASTM D226 FOR TYPE 1 FELT OR OTHER APPROVED WATER -RESISTIVE
<br />SELF -ADHERED FLASHING ;;;. <Illl"'
<br />FLASHING
<br />3DHE BEAD OF
<br />( O.6 Cm : 30.5 Cm
<br />BARRIER SHALL BE APPLIED OVER STUDS OR SHEATHING OF ALL EXTERIOR WALLS. SUCH FELT OR
<br />BY LAPPING DOWN =
<br />OVER RIM JOIST AND UP
<br />ADHESIVE TO BE APPLIED UNDER
<br />APPLIED
<br />THRESHOLD OF DOOR AND RETURN
<br />SELF -ADHERED FLASHING
<br />SELF -ADHERED F LAS H I N G
<br />MATERIAL SHALL BE APPLIED HORIZONTALLY, WITH THE UPPER LAYER LAPPED OVER THE LOWER
<br />LAYER NOT LESS THAN 2 INCHES (51 MM). WHERE JOINTS OCCUR, FELT SHALL BE LAPPED NOT
<br />WALL BY 6 IN. _
<br />_:
<br />UP JAMB 6'. USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />EXTERIOR
<br />PRODUCTS DETAILS
<br />LESS THAN 6 INCHES (152 MM). THE FELT OR OTHER APPROVED MATERIAL SHALL BE CONTINUOUS
<br />TO THE TOP OF WALLS AND TERMINATED AT PENETRATIONS AND BUILDING APPENDAGES IN A
<br />_
<br />CEMT.FIN.
<br />MANNER TO MEET THE REQUIREMENTS OF THE EXTERIOR WALL ENVELOPE AS DESCRIBED IN
<br />- -
<br />SELF -ADHERED FLASHING
<br />BUILDING PAPER
<br />SECTION R703.1. THE WATER -RESISTIVE BARRIER IS NOT REQUIRED FOR DETACHED ACCESSORY
<br />-
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />BUILDINGS.
<br />SEAL TOPS OF JOISTS :.. _ :..
<br />WIRE LATH
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC R703.2
<br />UNDER DECKING
<br />"lrq -
<br />SUBFLOOR
<br />(SEE DETAIL WP07) "'
<br />.;
<br />R703.4 FLASHING. APPROVED CORROSION -RESISTANT FLASHING SHALL BE APPLIED
<br />SHINGLE -FASHION IN A MANNER TO PREVENT ENTRY OF WATER INTO THE WALL CAVITY OR
<br />PENETRATION OF WATER TO THE BUILDING STRUCTURAL FRAMING COMPONENTS. SELF -ADHERED
<br />RIM JOIST
<br />Detail Instructions
<br />MEMBRANES USED AS FLASHING SHALL COMPLY WITH AAMA 711. ALL EXTERIOR FENESTRATION
<br />7Refer
<br />VAPPROPRIATE
<br />to the number marked as in each detail that corresponds to
<br />PRODUCTS SHALL BE SEALED AT THE JUNCTURE WITH THE BUILDING WALL WITH A SEALANT
<br />COMPLYING WITH AAMA 800 OR ASTM C920 CLASS 25 GRADE NS OR GREATER FOR PROPER JOINT
<br />the numbered items in the lis of instructions below:
<br />EXPANSION AND CONTRACTION, ASTM C1281, AAMA 812, OR OTHER APPROVED STANDARD AS
<br />FOR THE TYPE OF SEALANT. FLUID -APPLIED MEMBRANES USED AS FLASHING IN
<br />2
<br />O
<br />1. Install self -adhered flashing in order as shown by numbers
<br />EXTERIOR WALLS SHALL COMPLY WITH AAMA 714. THE FLASHING SHALL EXTEND TO THE SURFACE
<br />OF THE EXTERIOR WALL FINISH. APPROVED CORROSION RESISTANT FLASHINGS SHALL BE
<br />2. Install flashing and weather resistive barrier to form water
<br />shedding laps
<br />INSTALLED AT THE FOLLOWING LOCATIONS:
<br />SELF -ADHERED FLASHING
<br />P02
<br />FW
<br />SELF -ADHERED FLASHING
<br />W P03
<br />3. Self -adhered flashing can be substituted for building paper
<br />1• EXTERIOR WINDOW AND DOOR OPENINGS. FLASHING AT EXTERIOR WINDOW AND DOOR
<br />OPENINGS SHALL EXTEND TO THE SURFACE THE EXTERIOR WALL FINISH OR THE
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER
<br />4. Split the release paper using the ripcord (Split release on
<br />P P P 9 P ( P
<br />SE
<br />WATER -RESISTIVE BARRIER COMPLYING WITH SECTION 703.2 FOR SUBSEQUENT DRAINAGE.
<br />AI
<br />demand, embedded in the adhesive layer) - for ease of
<br />installation and to minimize scoring cuts
<br />MECHANICALLY ATTACHED FLEXIBLE FLASHINGS SHALL COMPLY WITH AAMA 712. FLASHING AT
<br />EXTERIOR WINDOW AND DOOR OPENINGS SHALL BE INSTALLED IN ACCORDANCE WITH ONE OR
<br />FOLD UP WEATHER
<br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT
<br />RESISTIVE BARRIER &
<br />TEMPORARILY SECURE
<br />EXTERIOR SHEATHING
<br />3/4"-t" BEAD OF CONSTR.ERED
<br />ADHESIVE TO BE APPLIED UNDER
<br />FLASHING JAMB 6INSTALL SELF-ADHHEAD
<br />RUBBERIZED
<br />NEEDED IN CORNERS ADHESIVE
<br />THROUGH SELF -ADHERED ASPHALT ADHESIVE
<br />5- Remove all release paper per standard installation instructions
<br />and adhere to substrate using a square piece of flashing material
<br />MORE OF THE FOLLOWING:
<br />1.1 THE FENESTRATION MANUFACTURER'S INSTALLATION AND FLASHING INSTRUCTIONS, OR
<br />WEATHER
<br />THRESHOLD OF DOOR AND RETURN
<br />FLASHING, SEE
<br />FLASHING SELF -ADHERED FLASHING s`7":`.`.'
<br />(6" X 6" Minimum)
<br />FOR APPLICATIONS NOT ADDRESSED IN THE FENESTRATION MANUFACTURER'S
<br />RESISITIVE
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />FLANGED WINDOW
<br />":%" t:;'
<br />:.,;.;;;.
<br />INSTRUCTIONS, IN ACCORDANCE WITH THE FLASHING MANUFACTURER'S INSTRUCTIONS.
<br />BARRIER
<br />OR EQUAL WEATHER PROOF CAULKING
<br />(SEE DETAIL WP01)
<br />6. Fold as shown by arrows
<br />WHERE FLASHING INSTRUCTIONS OR DETAILS ARE NOT PROVIDED, PAN FLASHING SHALL BE
<br />TAPE
<br />EXTERIOR
<br />(„gym` ^`''"A SCORED
<br />7. Angle of comer may vary, adjust folding of the flashing
<br />INSTALLED AT THE SILL OF EXTERIOR WINDOW AND DOOR OPENINGS. PAN FLASHING SHALL
<br />SHEATHING
<br />RELEASE PAPER
<br />accordingly to fit tight to comer
<br />BE SEALED OR SLOPED IN SUCH A MANNER AS TO DIRECT WATER TO THE SURFACE OF THE
<br />-(BEFORE
<br />SELF -A"•';•`'
<br />EXTENDAMINIMHERED LASHING,
<br />EXTEND A MINIMUM 6"
<br />FOLDING, SCORE
<br />_� RELEASE PAPER TO EXPOSE
<br />ADHESIVE AS SHOWN)
<br />8. Mechanical) fasten as necessary
<br />y ry
<br />EXTERIOR WALL FINISH OR TO THE WATER RESISTIVE BARRIER FOR SUBSEQUENT
<br />DRAINAGE. OPENINGS USING PAN FLASHING SHALL INCORPORATE FLASHING OR
<br />?',2.
<br />VERTICALLY FROM
<br />PROTECTION AT THE HEAD AND SIDES.
<br />:.:. :::, •,. :n
<br />••:•-:•- ""�:: •%>:_• "`''?
<br />2
<br />WEATHER
<br />'`' ''_ - RESISITIVE
<br />BARRIER
<br />'
<br />BOTTOM OF
<br />THRESHOLD
<br />1.2 IN ACCORDANCE WITH THE FLASHING DESIGN OR METHOD OF A REGISTERED DESIGN
<br />PROFESSIONAL.
<br />:"•: fc�
<br />-_=
<br />SECTION -A (SEE DETAIL WP02)
<br />1.3 IN ACCORDANCE WITH OTHER APPROVED METHODS.
<br />1.41N ACCORDANCE WITH FMA/AAMA 100, FMA/ AAMA 200, FMANVDMA 250, FMA/AAMA/ WDMA 300
<br />;-
<br />SELF -ADHERED FLASHING
<br />'O
<br />OR FMA/AAMANVDMA 400-
<br />2. AT THE INTERSECTION
<br />`:;'.
<br />2
<br />OF CHIMNEYS OR OTHER MASONRY CONSTRUCTION WITH FRAME OR
<br />HEAD FLASHING TIE-IN INSTRUXTIONS:
<br />STUCCO WALLS, WITH PROJECTING LIPS ON BOTH SIDES UNDER STUCCO COPINGS.
<br />1. Cut, fold up 8 temporarily secure weather resistive
<br />SELF -ADHERED FLASHING:• `
<br />5
<br />3. UNDER AND AT THE ENDS OF MASONRY, WOOD OR METAL COPINGS AND SILLS.
<br />barrier above header to allow for flashing
<br />installation
<br />'
<br />O
<br />4
<br />4. CONTINUOUSLY ABOVE ALL PROJECTING WOOD TRIM.
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />1
<br />SEAL TOPS OF JOISTS
<br />1
<br />5. WHERE EXTERIOR PORCHES, DECKS OR STAIRS ATTACH TO A WALL OR FLOOR ASSEMBLY OF
<br />WOOD -FRAME CONSTRUCTION.
<br />3. Fold weather resistive barrier back over head
<br />2
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />2
<br />7
<br />6. AT WALL AND ROOF INTERSECTIONS.
<br />flashing and seal with tape
<br />7. AT BUILT-IN GUTTERS.
<br />SELF -ADHERED FLASHING
<br />FLANGED WINDOW
<br />Scale: NTS
<br />WPM
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />EWP05
<br />SELF -ADHERED FLASHING
<br />INSIDE
<br />WP06
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />CORNER
<br />EXTERIOR SHEATHING �
<br />�Ground�
<br />SHEATHING
<br />-
<br />t
<br />7/8" Cement Plaster
<br />"
<br />7/8 Cement Plaster
<br />REFER TO TECHNICAL
<br />_ _
<br />�'<¢„<Y;,•-•_
<br />in accordance With
<br />in accordance with
<br />LETTER ON CHEMICAL
<br />::;,•.; , ..,;;.-:`
<br />Water Resistant Barrier
<br />ASTMC926
<br />ASTMC926
<br />COMPATIBILITY
<br />SELF -ADHERED FLASHING
<br />_ _
<br />Lath
<br />Felt backed metal
<br />Felt backed metal
<br />=
<br />SELF -ADHERED FLASHING
<br />- g
<br />Iat
<br />lathe e n accordance
<br />lathe in accordance
<br />PATCH
<br />With ASTMC1063
<br />with ASTMC1063
<br />Stucoo
<br />• ..
<br />.............
<br />Building Paper
<br />Buildingr
<br />Paper
<br />Pe
<br />-
<br />- _ _ _ _ _
<br />..:.... ...._.. .:.::R-:::.,::.:...._._.. �;..saa::�::..
<br />A •
<br />• :
<br />i "
<br />i 7/16 O.S.B.
<br />"
<br />, 7/16 O.S.B.
<br />ten... •
<br />^ :;.
<br />::
<br />SELF FLASHING
<br />::;;;;;;r.::::..::::...::....::.. ............... ......:..:....::u:.. ,...::::.:.-:,::n•:.�:s::::..
<br />..:;::::::::=:::..;;;::,::;.;:;�::...::::.::... :....::'�:,::-;.��-;> _::_;_ � .. ::r:::;•::_.:...:..n , ,
<br />:";`"'" :R.za :::a:::c:;a::=;r,;s•;_.:
<br />. a•
<br />:......::::. , , � . sheathin
<br />sheathin 9
<br />•
<br />-ADHERED
<br />.:_•
<br />................
<br />i
<br />SELF -ADHERED FLASHING
<br />Foundation Wall'• •'. '
<br />'
<br />Metal
<br />•
<br />SELF -ADHERED FLASHING "" > `<•': :' •':%£ 1 >t:
<br />%-4-'
<br />. �. .
<br />Flashing
<br />;•:;.. tt:• ..:..
<br />NAILING FLANGE 1
<br />3" MIN
<br />2
<br />+ • ;
<br />Weep Screed
<br />Installed As Per
<br />2
<br />4
<br />Manufact. Specs. &
<br />Stampede or similar
<br />DO NOT FLASH OVER
<br />FRC R703.7.2.1
<br />cejoint my
<br />BOTTOM NAILING
<br />8
<br />5
<br />FLANGE
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />SELF -ADHERED FLASHING
<br />WP04
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />KP08
<br />FOUNDATION WEEP SCREED
<br />WP09
<br />Weep Screed
<br />2" Above Roof
<br />Installed As Per
<br />&
<br />FRCR
<br />HALF ROUND WINDOW
<br />0.Spe1
<br />Sheathing
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside comer Will
<br />need to be miter
<br />Cement Plaster
<br />cut and caulked all
<br />in accordance
<br />butt joints need to
<br />with ASTMC926
<br />becaulked using
<br />over wood 2nd
<br />Stampede or sim.
<br />floor
<br />caulk for all
<br />DOUBLE
<br />JOIST
<br />SINGLE
<br />WOOD BEAM
<br />JOIST
<br />BELOW
<br />SELF -ADHERED
<br />SELF -ADHERED
<br />FLASHING
<br />FLASHING O
<br />2
<br />Cement
<br />SELF -ADHERED FLASHING
<br />�/rr/P07
<br />DECK JOIST
<br />V V
<br />Plaster
<br />over block
<br />1 st floor
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed. WEEP
<br />SCREED DETAIL
<br />NOT USED
<br />NOT USED
<br />NOT USED
<br />SCALE: NOT TO SCALE
<br />1111
<br />Im
<br />DANSCO
<br />ENGINEERING, LLC
<br />P.O. BOX 3400
<br />Apollo Beach, Florida 33572
<br />p. 813.645.0166
<br />1. 813.645.9698
<br />www.danscoengineedng.com
<br />CA 25948
<br />�
<br />p
<br />o
<br />acCRCn��
<br />z
<br />Q�CV)en
<br />Z
<br />Ln
<br />¢aN_J
<br />ZaF-CaaM
<br />�Q o
<br />Wz3
<br />o
<br />U
<br />i2
<br />LU
<br />W
<br />LU =
<br />CL
<br />LU to
<br />= O �
<br />� �
<br />J
<br />Q I m
<br />LU
<br />Q O 130
<br />Q I-_ m
<br />O
<br />Z LU
<br />Z
<br />Z 00
<br />(N
<br />C/)O �
<br />11
<br />V)
<br />TO THE BEST OF THE ENGINEER'S
<br />KNOWLEDGE AND BELIEF, THE STRUCTURAL
<br />PLANS AND SPECIFICATIONS COMPLY WITH
<br />6TH EDITION (2017) FLORIDA RESIDENTIAL
<br />BUILDING CODE, SECTION R301 FOR
<br />140 MPH (Vasd = I OBMPH), 3 SEC. GUST,
<br />EX OSURE "C" ENCLOSED (INTERNAL
<br />PRESSURE COEFFICIENT = 30.18) WIND ZONE
<br />THIS DRAWING AND DESIGN IS VAUD FOR 12 MONTHS
<br />AFTER THE DATE IT IS SKoNED AND SEALED.
<br />SIGNED AND SEALED FOR THE STRUCTURAL PORTION
<br />OFTHS DRAWINGONLY.
<br />02019 LENNAR CORP.-THIS PLAN MAY NOT BE
<br />REPRODUCED IN ANY MANNER WITHOUT WRITTEN
<br />CONSENT FROM LENNAR CORPORATION.
<br />02019 - THESE DRAWINGS AND DESIGNS ARE THE
<br />JOINT PROPERTY OF DANSCO ENGINEERING, LLC AND
<br />THE CLIENT ON THIS PROJECT. ANY REPRODUCTION
<br />OR UNAUTHORIZED USE IS PROHIMED.
<br />REVISION:
<br />DATE
<br />DESCRIPTION
<br />UPDATED CONNECTION
<br />06.08.18
<br />1.01 CROSS-REFERENCE TABLE
<br />AND STAIR STRAP
<br />01.09.19
<br />1.02 ROOF UNDERLAYMENT REV.
<br />02.11.19
<br />1.03 UPDATED CONNECTION
<br />CROSS-REFERENCE TABLE
<br />VERSK)N
<br />NO. 1.03 / 02.11.19
<br />o "�nanr,as>faaa
<br />N
<br />IIJn
<br />o c\�
<br />Q
<br />LU O
<br />Co J
<br />w 0
<br />-� LLI = U
<br />W C� Z
<br />W wM ='O Do
<br />UJ =* }* Lu*
<br />Z Q
<br />LLi = ui oe LLi
<br />V) �� 0-0-
<br />W ❑ ❑
<br />SHEET TITLE:
<br />WATERPROOFING DETAILS
<br />SHEET INFORMATION:
<br />JOB NO.: 390440
<br />DATE ISSUED: 04.04.19
<br />DRAWN BY: LF
<br />REVIEWED BY: TH
<br />W P
<br />O
<br />00
<br />O
<br />I
<br />CAI
<br />r_1
<br />I
<br />Ob
<br />LO
<br />9-
<br />
|