|
OPTIONAL OVERHEAD SERVICE 5AME A5
<br />150 = ' COPPER OR 2/0 ALUMINUM
<br />UNDERGROUND 150 OR 200 AMP 5ERVICE
<br />200 = 2/0 COPPER OR 4/0 ALUMINUM IN 2" CONDUIT,
<br />METER
<br />TYPICAL =====fA/C
<br />MAIN D15G. ELECTRICAL DI5CONNECT
<br />150 OR PANEL
<br />REFER TO FLOOR PLAN FOR
<br />200 AMP 12 COPPER TO APPLIANCES AND GFI
<br />NOTED AMPS. REQUIRED
<br />14 COPPER TO LIGHT5 AND OUTLET5
<br />`10 COPPER TO WATER HEATER
<br />UNDERGROUND 5ERVICE
<br />18 COPPER TO RANGE
<br />BY POWER COMPANY
<br />% COPPER TO HVAC
<br />04 GROUNDING WIRE WITH CODE
<br />APPROVED CLAMP PER 250.50
<br />AND 25052 OF THE 2014 NEC,
<br />INTER5Y5TEM BONDING TERMINATION PER NEC 08, 250.94
<br />ELECTRICAL RISER DIAGRAM
<br />NOTE:
<br />ELECTRICAL MATERIALS AND IN5TALLATION5 5HALL COMPLY W/ APPLICABLE PROV151ON5
<br />OF THE NFPA 10-06, LOCAL GODE5 AND LOCAL POWER/UTILITY COMPANY
<br />5TAIR NOTE5
<br />RAILING
<br />BALU5TER5 5HALL BE SPACED 50 THAT A 4" SPHERE CANNOT PA55 THROUGH.
<br />HANDRAILS
<br />HANDRAIL5 FOR 5TAIRWAY5 5HALL BE CONTINUOUS FOR THE FULL LENGTH OF THE FLIGHT, FROM A POINT DIRECTLY ABOVE THE TOP R15ER OF
<br />THE FLIGHT TO A POINT DIRECTLY ABOVE THE LOWE5T RISER HANDRAIL END5 5HALL BE RETURNED OR 5HALL TERMINATE IN NEWEL P05T5 OR
<br />5AFETY TERMINAL5. HANDRAIL5 ADJACENT TO A WALL SHALL HAVE A 5PACE OF NOT LE55 THAN 1-1/2 INCH BETWEEN THE WALL AND HANDRAIL5.
<br />CONTINUOUS GRA5PABLE HANDRAIL MUST MEET TYPE ONE OR TYPE TWO CRITERIA
<br />UNDER -STAIR PROTECTION
<br />ENCL05ED ACCE551BLE 5PACE UNDER 5TAIR5 5HALL HAVE WALLS, UNDER-5TAIR SURFACE AND ANY SOFFIT PROTECTED ON THE
<br />ENCLOSED 51DE W/ 1/2 INCH GYPSUM BOARD PER F.B.C. RE51DENTIAL 6th EDITION (2011) - R302.1 AND R302.11
<br />STAIRWALL FRAME NOTE
<br />ALL 5TAIRWELL 5URROUNDING WALLS AND KNEE WALL5 ARE TO BE FRAMED AT 16" O.C. TO PROTECT FROM FALLING HAZARD
<br />OCCUPANCY AND CON5TRUCTION TYPE:
<br />TH15 UNIT HA5 AN R3 OCCUPANCY AND BUILDING TYPE V-B CLA551FICATION,
<br />CEILING CON5TRUCTION.
<br />I. THE GARAGE 5HALL BE 5EPARATED FROM THE RESIDENCE AND IT5 ATTIC AREA BY NOT LE55 THAN 1/2 INCH (12.1 mm) GYP5UM BOARD APPLIED
<br />TO THE GARAGE 51DE, GARAGE5 BENEATH HABITABLE ROOM5 5HALL BE SEPARATED FROM ALL HABITABLE ROOM5 ABOVE BY NOT LE55 THAN
<br />5/8 INCH (15.9 mm) TYPE "X" GYP5UM BOARD OR EQUIVALENT. WHERE THE 5EPARATION 15 A FLOOR -CEILING A55EMBLY, THE 5TRUCTURE
<br />5UPPORTING THE 5EPARATION 5HALL AL50 BE PROTECTED BY NOT LE55 THAN 1/2 INCH (12.1 mm) GYP5UM BOARD OR EQUIVALENT.
<br />DUELLING / GARAGE OPENING5:
<br />I. THE OPENING BETWEEN THE GARAGE AND LIVING AREA 5HALL BE EQUIPPED WITH SOLID WOOD DOOR5 NOT LE55 THAN 13/8" IN THICKNESS,
<br />50LID CORE (5.C.) OR HONEYCOMB CORE 5TEEL DOOR5 NOT LE55 THAN 13/8" THICK, OR 20 MINUTE FIRE RATED DOOR5.
<br />2. ALL DOORS FROM GARAGE ADJACENT TO LIVING 5PACE MU5T BE EITHER A 50LID CORE DOOR OR HAVE A MIN. FIRE RATING OF 20 MINUTE5.
<br />EGRE55:
<br />EACH BEDROOM MU5T HAVE ONE WINDOW THAT COMPLIE5 WITH EGRE55 CODE5, IF THERE 15 NO AGGE55 TO EXTERIOR THROUGH A DOOR, THE
<br />WINDOW MUST HAVE A MAXIMUM OPENING HEIGHT OF 44" ABOVE FIN15H FLOOR LINE OF THAT PARTICULAR ROOM.
<br />WINDOW IN5TALLATION:
<br />WINDOW5 5HALL BE I1\15TALLED AND FLASHED IN ACCORDANCE WITH THE MANUFACTURERS WRITTEN INSTALLATION IN5TRUCTION5. WRITTEN
<br />INSTALLATION IN5TRUCTION5 5HALL BE PROVIDED BY THE MANUFACTURER FOR EACH WINDOW,
<br />TERMITE PROTECTION:
<br />I. PENETRATION. PROTECTIVE 5LEEVE5 AROUND PIPING PENETRATING CONCRETE SLAB -ON -GRADE FLOOR5 5HALL NOT BE OF CELLULOSE
<br />CONTAINING MATERIAL5. IF 501L TREATMENT 15 U5ED FOR SUBTERRANEAN TERMITE PROTECTION, THE SLEEVE 5HALL HAVE A MAXIMUM WALL
<br />THICKNESS OF 0.010 INCH, AND BE SEALED WITHIN THE SLAB U51NG A NON-GORRO51VE CLAMPING DEVICE TO ELIMINATE THE ANNULAR 5PACE
<br />BETWEEN THE PIPE AND THE 5LEEVE. NO TERMITICIDE5 5HALL BE APPLIED IN51DE THE 5LEEVE.
<br />2. PROTECTION AGAINST DECAY AND TERMITES. - CONDENSATE LINES, IRRIGATION / 5PRINKLER 5Y5TEM R15ER5 FOR 5PRAY HEADS, AND ROOF
<br />DOWN5POUT5 5HALL D15CPARGE AT LEAST I FOOT (305 mm) AWAY FROM THE STRUCTURE 51DEWALL, WHETHER BY UNDERGROUND PIPING, TAIL
<br />EXTEN51ON5, OR 5PLA5H BLOCK5. GUTTER5 WITH DOWN5POUT5 ARE REQUIRED ON ALL BUILDING5 WITH EAVE5 OF LE55 THAN 6 INCHE5 (152 mm)
<br />HORIZONTAL PROJECTION EXCEPT FOR GABLE END RAKE5 OR ON A ROOF ABOVE ANOTHER ROOF.
<br />I
<br />TOP RAILING
<br />NOTE: 5UBFLOOR ADHESIVE 15 U5ED IN ADDITION
<br />BALU5TER5 TO NAIL5 ON WOOD COMPONENTS,
<br />MAX SPACING 4"
<br />1 X 8 PAINTED WE). CAP 5TRINGER 15 LAMINATED TO A THICKNE55 EQUIVALENT TO
<br />OGEE 5TOP THE 51ZE OF A 2 X 12 5.Y.P. AND 15 NAILED TO EACH
<br />TREAD W/ 16d NAILS FROM THIRD LAMINATE TO TREAD—
<br />OPT, 2 X 2 BLOCKING NAILED /
<br />TO TREAD AND RISER.
<br />3-2 X 12 5TRINGER 2 X BLOCKING NAILED TO 5TRINGER, Z +
<br />3/4" R15ER5 RISER, AND TREAD. +
<br />2 X TREADS± RIP FROM 2x12 I X 5PRUCE 13 OR 3/4" CDX. +
<br />TO 51ZE NOTED ON PLAN PLYWD. RISER.
<br />2 X 5OUTHERN YELLOW PINE 01
<br />(ACTUAL THICKNESS 15 1 1/2") TREAD,
<br />TYP. OPT. RAILING ELEVATION
<br />5CALE: 1/2" = 1411
<br />NEWEL P05T
<br />TOP RAILING
<br />BALU5TER 4" O.C.
<br />5HOE RAIL (REMOVE
<br />W/ METAL SPINDLES)
<br />I X 8 PAINTED WD. CAP
<br />OGEE STOP
<br />r uuK LINt _
<br />OPTIONAL
<br />A RAILING DETAIL
<br />CLOSED RISER DETAIL
<br />5CALE: 1/2" = 1'-0"
<br />CARPf
<br />CARPS
<br />TREAD
<br />R15ER
<br />2X4WALL
<br />1/2" GYP BD.
<br />3/4" SKIRT BD.
<br />2 X 4 5PACER
<br />2X12
<br />5TRINGER
<br />TYPICAL STAIR
<br />FRAMING DETAIL
<br />B 5CALE: 3/4" = I'-0"
<br />GENERAL CONSTRUCTION NOTES
<br />CHAPTER5 AND 5ECTION5 REFER TO F.B.C. RESIDENTIAL 6th EDITION (2011)
<br />MECHANICAL AND HVAC
<br />I. ENERGY CALCULATION5 FOR HEATING AND COOLING CAPAGITIE5 5HALL BE FURN15HED BY THE GENERAL CONTRACTOR A5 AN ATTACHMENT TO
<br />TH15 PLAN SET AT THE TIME OF APPLICATION FOR PERMIT.
<br />2. MECHANICAL APPLIANCE5 5HALL BE ACCE551BLE FOR INSPECTION, 5ERVICE, REPAIR, AND REPLACEMENT WITHOUT REMOVING PERMANENT
<br />GON5TRUCTION, OTHER APPLIANCE5, OR ANY OTHER PIPING OR DUCT5 NOT CONNECTED TO THE APPLIANCE BEING INSPECTED, SERVICED,
<br />REPAIRED, OR REPLACED. A LEVEL WORKING 5PACE AT LEAST 30 INCHE5 (162 mm) DEEP AND 30 INCHE5 (162 mm) WIDE 5HALL BE PROVIDED IN
<br />FRONT OF THE CONTROL 51DE TO 5ERVICE AN APPLIANCE.
<br />3. DUCT5 IN THE GARAGE AND DUCT5 PENETRATING THE WALL5 OR CEILING5 5EPARATING THE DWELLING FROM THE GARAGE 5HALL BE
<br />CONSTRUCTED OF A MIN. 126 GAUGE (0.48 mm) 5HEET 5TEEL OR OTHER APPROVED MATERIAL AND 5HALL HAVE NO OPENING5 INTO THE GARAGE.
<br />4. FOUNDATION5 AND 5UPPORT5 FOR OUTDOOR MECHANICAL 5Y5TEM5 5HALL BE RAISED AT LEAST 3 INCHE5 (16 mm) ABOVE THE FIN15HED
<br />GRADE AND 5HALL AL50 CONFORM TO THE MANUFACTURER'5 INSTALLATION IN5TRUCTION5.
<br />5. AUXILIARY DRAIN PAN. CATEGORY IV CONDENSING APPLIANCE5 5HALL BE PROVIDED WITH AN AUXILIARY DRAIN PAN WHERE DAMAGE TO
<br />ANY BUILDING COMPONENT WILL OCCUR A5 A RE5ULT OF 5TOPPAGE IN THE CONDENSATE DRAIN PIPING 5Y5TEM. THESE PANS 5HALL BE
<br />INSTALLED IN ACCORDANCE WITH THE APPLICABLE PROV1510N5 OF 5ECTION5 MI411.3.
<br />EXHAU5T FANS AND VENTING:
<br />(.OUTDOOR D15CHARGE. THE AIR REMOVED BY EVERY MECHANICAL EXHAU5T 5Y5TEM 5HALL BE D15CHARGED TO THE OUTDOOR5. AIR 5HALL
<br />NOT BE EXHAU5TED INTO AN ATTIC, SOFFIT, RIDGE VENT OR CRAWL 5PACE.
<br />2, EXHAU5T AIR FROM BATH ROOM5 AND TOILET ROOM5 5HALL NOT BE RECIRCULATED WITHIN A RESIDENCE OR TO ANOTHER DWELLING UNIT AND
<br />5HALL BE EXHAU5TED DIRECTLY TO THE OUTDOOR5. EXHAU5T AIR FROM BATHROOMS AND TOILET ROOM5 5HALL NOT D15CHARGE INTO AN ATTIC,
<br />CRAWL 5PACE, OR OTHER AREA5 IN51DE THE BUILDING.
<br />3. DUCT LENGTH. THE MAXIMUM LENGTH OF A CLOTHE5 DRYER EXHAU5T DUCT 5HALL NOT EXCEED 25 FEET FROM THE DRYER LOCATION TO THE
<br />WALL OR ROOF TERMINATION. THE MAXIMUM LENGTH OF THE DUCT 5HALL BE REDUCED 2.5 FEET (162 mm) FOR EACH 45 DEGREE (0.19 RAD) BEND
<br />AND 5 FEET (1524 mm) FOR EACH 90 DEGREE (1.6 RAD) BEND. THE MAXIMUM LENGTH OF THE EXHAU5T DUCT DOES NOT INCLUDE THE TRANSITION
<br />DUCT.
<br />EXCEPTION - WHERE A CLOTHES DRYER 5005TER FAN 15 IN5TALLED AND 115TED AND LABELED FOR THE APPLICATION, THE MAXIMUM LENGTH OF
<br />THE EXHAU5T DUCT, INCLUDING ANY TRAN51TION DUCT, 5HALL BE PERMITTED TO BE IN ACCORDANCE WITH THE 5005TER FAN MANUFACTURER'S
<br />IN5TALLATION IN5TRUCTION5. WHERE A CLOTHES DRYER 8005TER FAN 15 INSTALLED AND NOT READILY ACCE551BLE FROM THE ROOM IN WHICH
<br />THE DRYER 15 LOCATED, A PERMANENT IDENTIFYING LABEL 5HALL BE PLACED ADJACENT TO WHERE THE EXHAU5T DUCT ENTER5 THE WALL. THE
<br />LABEL 51-1ALL BEAR THE WORD5 "TH15 DRYER EXHAU5T 5Y5TEM 15 EQUIPPED WITH A REMOTELY LOCATED 5005TER FAN."
<br />4. PROVIDE LOUVER DEVICE5 AT INTAKE AND EXHAU5T LOCATION5 IN ACCORDANCE WITH
<br />AMCA 5TANDARD 550 IN FBC,
<br />ROUGH -IN IN5PECTION REQUE5T NOTE
<br />ALL PLUMBING, ELECTRICAL AND MECHANICAL ROUGH-IN5 MU5T BE
<br />COMPLETE, INSPECTED AND APPROVED BEFORE REQUE5TING THE
<br />FRAMING INSPECTION.
<br />WINDOW FALL PROTECTION
<br />IN DWELLING UNITS, WHERE THE OPENING OF AN OPERABLE WINDOW 15
<br />LOCATED MORE THAN 12 INCHE5 ABOVE THE FINI5HED GRADE OR
<br />5URFACE BELOW, THE LOWEST PART OF THE CLEAR OPENING OF THE
<br />WINDOW SHALL BE A MINIMUM OF 24 INCHE5 ABOVE THE FINI5HED
<br />FLOOR OF THE ROOM IN WHICH THE WINDOW 15 LOCATED. OPERABLE
<br />5ECTION5 OF WINDOW5 SHALL NOT PERMIT OPENING5 THAT ALLOW
<br />PA55AGE OF A 4 INCH DIAMETER 5PHERE WHERE 5UCH OPENINGS
<br />ARE LOCATED WITHIN 24 INCHE5 OF THE FINI5HED FLOOR PER F.B.C.
<br />RESIDENTIAL 6th EDITION (2011) - 5ECTION R312.2.
<br />WINDOW FALL PREVENTION DEVICE5 AND WINDOW GUARD5, WHERE
<br />PROVIDED, 5HALL COMPLY WITH THE REQUIREMENT5 OF A5TM F 2090
<br />PER F.B.G. RESIDENTIAL 6th EDITION (2011)- SECTION R3122,
<br />IN5ULATION NOTE5
<br />• CMU WALLS:----- R-FOIL 4.1 KNEE WALL5 THAT
<br />BACK UP TO CEILING
<br />• FRAME WALLS:-------- R-13 AREA ONLY:----------- R-19
<br />• CEILING:------------- R-30
<br />ON51TE FOUNDATION 5URVEY NOTE
<br />A FOUNDATION 5URVEY 5HALL BE PERFORMED AND A COPY OF THE
<br />5URVEY 5HALL BE ON THE 51TE FOR THE BUILDING IN5PECTOR'5 U5E,
<br />OR ALL PROPERTY MARKER5 5HALL BE EXP05ED AND A STRING
<br />5TRECHED FROM MARKER TO MARKER TO VERIFY REQUIRED
<br />SETBACKS,
<br />CELING AT ENTRY NOTE
<br />ALL ENTRY CLG5, TO BE 15/32 058. CEMENTITOU5 FIN15H (UN.0)
<br />GA5 APPLIANCE PROTECTION IN GARAGE NOTE
<br />PROTECTION OF GAS APPLIANCES IN RE5IDENTIAL GARAGE5:
<br />MINIMUM 3" DIAMETER 5CH 40 5TEEL PIPE, 2 FT. BELOW CONCRETE
<br />SLAB AND 3 FT. ABOVE FINISHED FLOOR,
<br />GENERAL NOTES
<br />• DUE TO VARIATION5 IN CITY REQUIREMENT5, 5UBDIV1510N
<br />5PECIFICATION5, CON5TRUCTION TECHNIQUES, DIVERSITY IN
<br />MATERIAL5, AND PLAN REV1510N5, ALL DIMEN51ON5 AND
<br />ELEVATION5 MAY VARY PER INDIVIDUAL PLAN. ACTUAL FIELD
<br />CONDITION5 MAY VARY AND MU5T BE VERIFIED BEFORE
<br />PROCEEDING WITH CONSTRUCTION.
<br />• ELECTRICAL LOCATION5 5HM ON DRAWING5 MAY BE CHANGED
<br />AT THE 50LE D15CRETION OF CALATLANTIC HOMES OR IT5
<br />LICENSED ELECTRICIAN IN ORDER TO COMPLY W/ NATIONAL AND
<br />MUNICIPAL BUILDING AND ELECTRICAL CODE5. CALATLANTIC
<br />HOMES WILL NOT GUARANTEE LOCATION OR QUANTITY OF OUTLET5
<br />AND / OR 5WITCHE5 5HOWN.
<br />• ALL PLUMBING DIMEN51ON5 ARE APPROXIMATE FROM THE CENTER
<br />LINE OF THE FIXTURE TO THE EXTERIOR 5LA8 EDGE. IT 15 THE
<br />RE5PON51BILITY OF THE PLUMBER TO VERIFY THE ACCURACY OF
<br />ALL PLUMBING DIMEN51ON5.
<br />NOTE: ANY DIMEN51ON5 AND/OR CALLOUT5 WITHIN TH15 5ET OF DRAWING5 REFERENCING
<br />LUMBER 51ZE5 OR WALL THICKNE55E5 ARE TO BE CON5IDERED "NOMINAL DIMEN51ON5"
<br />CHIMNEY HEIGHT REQUIREMENT5:
<br />WHEN 5TANDARD OR OPTIONAL FIREPLACE 15 TO BE INSTALLED THE CHIMNEY MUST EXTEND 3'-0" PAST THE HIGHER POINT WHERE IT
<br />EXTEND5 THROUGH THE ROOF AND MUST BE 2'-0" HIGHER THAN THE ROOF OR RIDGE THAT 1510'-0" AWAY OR CLOSER.
<br />TUE3 AND 5HOWER AREAS:
<br />CEMENT, FIBER -CEMENT, OR GLA55 MAT GYP5UM BOARD (NO GREEN BOARD ALLOWED) IN COMPLIANCE WITH 45TM 5288, 5325, OR C1118
<br />AND INSTALLED IN ACCORDANCE WITH MANUFACTURER RECOMMENDATION5 5HALL BE USED A5 BACKER5 FOR WALL TILE IN TUB AND
<br />5HOWER AREA5, AND WALL PANEL5 IN 5HOWER ARE45.
<br />FLOOD ZONE REQUIREMENT5:
<br />PLAN MEETS OR EXCEED5 FEMA FLOOD FINISHED GARAGE FLOOR ELEVATION.
<br />DAMS BEWS
<br />DESIGN GROUP
<br />150 STATE STREET EAST
<br />OLL76MAlt, FI.O1tIDA 34677
<br />813.92.5.1300 TEL
<br />813.925.1800 FAX
<br />WWW.DAVISBEWS.COM
<br />TAMI'A • DEIVVER.
<br />� EST. 1994 �-
<br />t
<br />0
<br />z "
<br />N
<br />(7�o
<br />>�mC)
<br />�) M �
<br />oLn
<br />Q fl. �
<br />U 0- 00
<br />z��
<br />w Wo
<br />J O
<br />�o
<br />oz
<br />�s
<br />w�
<br />za
<br />Z�
<br />w¢wd
<br />V) ro-
<br />J
<br />0
<br />H �aWZ
<br />�aO�n
<br />Lq
<br />8 Ce K o
<br />Ow�N
<br />W COzO
<br />oN
<br />Q zz
<br />r8
<br />�z
<br />zw
<br />z a
<br />0 ��
<br />Ob ;::; Q Q
<br />p--1
<br />D ce �-
<br />Oz
<br />�w
<br />w 0
<br />LJ.J
<br />oc z Q oN w
<br />z ...
<br />Lu
<br />z U z z 0
<br />0_U
<br />u.i z
<br />O '-'
<br />z Q Lu 0
<br />m z
<br />0 g
<br />r, a w 00
<br />SCALE : AS NOTED
<br />DATE : 10-19-2018
<br />VERSION NO.
<br />iso
<br />SHEET NO.
<br />DTI
<br />
|