Laserfiche WebLink
COLUMN CONSTRUC' <br />STUCCO <br />(CEMENT PLASTER) <br />LATH <br />2 LAI <br />WEEP <br />1 COLUMN AT CONCRETE SLAB <br />SCALE: N.T.S. <br />BARRIER <br />FLASHING <br />NAILING: PII <br />NO 5EALA <br />MAKE SURE THE SHEATHING WRAP LAPS OVER THE TOP <br />FIN. LEAVE A I/4" GAP BETWEEN THE EXTERIOR FINISH <br />AND THE FLANGE, BUT DON'T CAULK THIS GAP. WATER <br />DRAINING FROM ABOVE MUST HAVE A PLACE TO EXIT, <br />6 FIN WINDOW HEAD DETAIL <br />SCALE: N.T.5. <br />CORNER BEAD FASTENED WITH <br />NAILS, SCREWS, OR STAPLES AT <br />5TUCC( <br />OUTSIDE CORNER <br />INSIDE CORNER <br />NOTE: <br />2 STUCCO DETAIL AT CORNERS <br />SCALE:NJ5 <br />BEAD OF SILICON <br />CAULK UNDER <br />WINDOW FLANGE <br />SEALANT <br />BITUMINOUS <br />MEMBRANE OR FELT <br />STUCCO BAND <br />EXTERIOR FINISH <br />SILL DETAIL <br />7 FIN WINDOWS EXT. CASINGS <br />SCALE: N.T.S. <br />BACK CAULK SILL DAM <br />AND 12" UP WALL EACH 51DE <br />STOP FLASHING HERE AINTERIOR <br />PEEL -AND -STICK <br />MEMBRANE <br />2 LAYERS <br />W.R.B. <br />SHEATHING <br />NOTES: <br />APPLY A NARROW DAM STRIP TO THE ROUGH SILL BEFORE FLASHING WITH <br />SHEATHING WRAP OR A FLEXIBLE FLASHING MEMBRANE <br />3 SILL FLASHING DETAILS <br />SCALE: N.T.5. <br />EXTERIOR FINISH <br />STUCCO BAND <br />BITUMINOUS <br />MEMBRANE OR FELT <br />STEP 1 <br />INSTALL THE VENT ACCORDING TO THE <br />MANUFACTURER'S RECOMMENDATIONS, TRIM <br />THE HOUSE WRAP A CL05E AS P0551BLE <br />AROUND THE PERIMETER OF THE VENT. <br />SELF ADHESIVE <br />MEMBRANE FLASHING <br />AT DOORS <br />BACK CAULK SILL <br />AND 12" UP WALL <br />EACH 51DE <br />WOOD FRAME <br />4 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />STEP 2 <br />FLASH THE VENT U51NG THE SAME METHOD AS WINDOWS. STARTING AT <br />THE BOTTOM FLANGE: CUT THE FLASHING SO THAT IT EXTENDS PAST <br />THE FLANGES BY I" ON BOTH SIDES. NOW APPLY THE FLASHING TO <br />THE SIDES OF THE VENT. REMEMBER TO EXTEND THE FLASHING I" ON <br />BOTH TOP AND BOTTOM. MAKE SURE TO SMOOTH OUT WRINKLES AND <br />AIR BUBBLES. THE USE OF A J-ROLLER 15 OPTIONAL. <br />PREFABDOOR THRESHOLD I DOORMETAL EXTERIOR <br />FORMED "SEAT" IN <br />CONCRETE SLAB ACTS <br />AS PAN FLASHING — <br />• v <br />zSLAB ON GRADE s USE <br />° PLASTIC <br />SHIMS <br />CONCRETE SLAB UNDER <br />R <br />5 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />NOTE: <br />THIS TYPE OF INSTALLATION 15 SUITABLE FOR SEVERAL DIFFERENT PENETRATIONS. ALWAYS <br />USE THE SHINGLING METHOD AND ENSURE A TIGHT SEAL AROUND THE FLANGE/PENETRATION. <br />8 FRAME WALL FLASHING PENETRATIONS <br />1 SCALE: N.T.S. <br />STEP 3 <br />THE FINAL STEP IS TO INSTALL THE <br />FLASHING ACROSS THE TOP. EXTEND THE <br />FLASHING OUT AT LEAST I" ON BOTH SIDES. <br />BEWS <br />DESIGN GROVP <br />150 STATE STREET' EAST <br />OLDSMAR, FLORmA 3l6T7 <br />813.923.1300 TEL <br />813.92.5.1800 FAX <br />WWW.DAVISBEWS.CAM <br />TAMI'A • DENVEfi. <br />� EST. 1994 � <br />O <br />Z oN <br />0 <br />M <br />0 M Ln <br />N .0 IJ <br />LL <br />DC V C.00 <br />z��� <br />w Wo <br />J O <br />d' <br />oZ <br />w� <br />za <br />aQ <br />fF <br />wQ�a <br />r80 <br />�� <br />J �LLI <br />aWW <br />d J <br />a�LLo <br />8mt© <br />W oV) <br />0 ZZ <br />r0 <br />z <br />Lu <br />Z z g <br />O v� 3 <br />O Q <br />0 W <br />u_ <br />LI) <br />V �Lu <br />Q Q �(V W <br />Z <br />0 <br />Lu <br />z U z zO <br />0_U <br />w z F- U <br />z a Lu o <br />0° Z i <br />o In- w m <br />SCALE : AS NOTED <br />DATE : 10-19-2018 <br />VERSION NO. <br />loo <br />SHEET NO. <br />DAVISDT4 <br />