Laserfiche WebLink
COLUMN CONSTRUCT <br />STUCCO <br />(CEMENT PLASTER) <br />LATH <br />2 LAYERS WRB---`Nil <br />WEEP SCREED �� . e <br />CONCRETE STOOP I <br />1 COLUMN AT CONCRETE SLAB <br />SCALE: N.T.S. <br />BARRIER PAPER <br />FLASHING <br />NAILING FIN <br />NO 5EALANT—,, <br />NOTE: <br />MAKE SURE THE SHEATHING WRAP LAPS OVER THE TOP <br />FIN. LEAVE A 1/4" GAP BETWEEN THE EXTERIOR FINISH <br />AND THE FLANGE, BUT DON'T CAULK TH15 GAP. WATER <br />DRAINING FROM ABOVE MUST HAVE A PLACE TO EXIT. <br />6 FIN WINDOW HEAD DETAIL <br />SCALE: N.T.S. <br />CORNER BEAD FASTENED WITH <br />NAILS, SCREWS, OR STAPLES AT <br />/" n/' \/ice?lP Al I V <br />STUCCO <br />OUTSIDE CORNER <br />WIFE LATH <br />CEMENT PLASTER <br />(STUCCO) <br />INSIDE CORNER <br />2 STUCCO DETAIL AT CORNERS <br />1 SCALE: N.T.S. <br />BACK CAULK SILL DAM <br />AND 12" UP WALL EACH SIDE <br />STOP FLASHING HERE INTERIOR <br />PEEL -AND -STICK <br />MEMBRANE <br />2LAYERS <br />W.R.B. <br />SHEATHING <br />NOTES: <br />APPLY A NARROW DAM STRIP TO THE ROUGH SILL BEFORE FLASHING WITH <br />SHEATHING WRAP OR A FLEXIBLE FLASHING MEMBRANE <br />3 SILL FLASHING DETAILS <br />SCALE: N.T.S. <br />EXTERIOR FINISH <br />BEAD OF 51LICONE / - <br />CAULK UNDER <br />WINDOW FLANGE <br />SEALANT <br />STUCCO BAND <br />BITUMINOUS <br />MEMBRANE OR FELT 7 <br />BITUMINOUS <br />STUCCO BAND MEMBRANE OR FELT <br />EXTERIOR FINISH <br />SILL DETAIL HEADER DETAIL <br />7 FIN WINDOWS EXT. CASINGS <br />SCALE: N.T.S. <br />STEP 1 <br />INSTALL THE VENT ACCORDING TO THE <br />MANUFACTURER'S RECOMMENDATIONS. TRIM <br />THE HOUSE WRAP A CLOSE AS P0551BLE <br />AROUND THE PERIMETER OF THE VENT. <br />SELF ADHESIVE <br />MEMBRANE FLASHING <br />AT DOORS <br />BACK CAULK 51LL <br />AND 12" UP WALL <br />EACH SIDE <br />WOOD FRAME <br />4 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />STEP 2 <br />FLASH THE VENT U51NG THE SAME METHOD AS WINDOWS. STARTING AT <br />THE BOTTOM FLANGE: CUT THE FLASHING 50 THAT IT EXTENDS PAST <br />THE FLANGES BY I" ON BOTH SIDES. NOW APPLY THE FLASHING TO <br />THE 51DE5 OF THE VENT. REMEMBER TO EXTEND THE FLASHING I" ON <br />BOTH TOP AND BOTTOM, MAKE SURE TO SMOOTH OUT WRINKLES AND <br />AIR BUBBLES. THE USE OF A J•ROLLER 15 OPTIONAL. <br />PREFAB METAL EXTERIOR <br />DOOR THRESHOLD DOOR <br />FORMED "SEAT" IN <br />CONCRETE SLAB ACTS <br />AS PAN FLASHING <br />G�.S fl <br />v �v <br />Z5LAB ON GRADE e USE <br />° ° A PLASTIC <br />SHIMS <br />CONCRETE SLAB UNDER <br />DODR <br />5 FLASHING DOOR THRESHOLD <br />SCALE: N.T.S. <br />NOTE <br />THIS TYPE OF INSTALLATION IS SUITABLE FOR SEVERAL DIFFERENT PENETRATIONS. ALWAYS <br />USE THE SHINGLING METHOD AND ENSURE A TIGHT SEAL AROUND THE FLANGE/PENETRATION. <br />8 FRAME WALL FLASHING PENETRATIONS <br />1 SCALE: N.T.S. <br />STEP 3 <br />THE FINAL STEP 15 TO INSTALL THE <br />FLASHING ACROSS THE TOP. EXTEND THE <br />FLASHING OUT AT LEAST I" ON BOTH SIDES. <br />NOTE <br />THIS TYPE OF INSTALLATION IS SUITABLE FOR SEVERAL DIFFERENT PENETRATIONS. ALWAYS <br />USE THE SHINGLING METHOD AND ENSURE A TIGHT SEAL AROUND THE FLANGE/PENETRATION. <br />8 FRAME WALL FLASHING PENETRATIONS <br />1 SCALE: N.T.S. <br />STEP 3 <br />THE FINAL STEP 15 TO INSTALL THE <br />FLASHING ACROSS THE TOP. EXTEND THE <br />FLASHING OUT AT LEAST I" ON BOTH SIDES. <br />DAVIS BEWS <br />DESIGN GROUP <br />Lso srA-rE sr�er eAsl' <br />o1.D6titAtt, F1.oItIDA 34677 <br />813.9'Z5.1300 TEL <br />813.925.1800 FAX <br />W W W.DAVISBEWS.C.OM <br />T.1MPA • DENVER <br />----------------------- <br />O <br />Z � <br />0 cu r, <br />i-. <br />M O <br />j M l^ <br />Ln <br />CL <br />LL <br />DC U a 0 <br />¢ E `. <br />Z <br />w Wo <br />J O <br />�o <br />J <br />Oz <br />�o <br />w� <br />za <br />Z80 <br />�L) <br />qqU <br />J �Ezz <br />E f JJ <br />w S LL <br />W � N <br />W �W° <br />Q Z z <br />rzo <br />f z <br />Z <br />0 <br />O ¢ Q <br />CC F— <br />OZ <br />W <br />Q Z Q N W <br />Z <br />LLJ <br />z U Z z O <br />W OU <br />z � <br />z �uw C] <br />zCD <br />_ <br />cl <br />g w m <br />SCALE : AS NOTED <br />DATE : 10-19-2018 <br />VERSION NO. <br />100 <br />SHEET NO. <br />DT4 <br />