Laserfiche WebLink
^' ^ ' "' WEATHER <br />✓E BARRIER & <br />I.ARILY SECURE <br />WEATHER <br />RESISITIVE <br />BARRIER <br />WOOD FRAME CONSTR. <br />TAPE <br />EXTERIOR <br />SELF -ADHERED FLASHIN <br />a <br />SHEATHING <br />BY LAPPING DOWN -� <br />OVER RIM JOIST AND UP <br />WALL BY 6 IN. <br />(ASSEMBLED WINDOW) <br />- <br />2 <br />WEATHER <br />\ <br />RESISI•TIVE <br />BARRIER <br />SEAL TOPS OF JOISTS- <br />- <br />UNDER DECKING <br />_ <br />SELF -ADHERED FLASHING <br />(SEE DETAIL WP07) / <br />HEAD FLASHING TIE-IN INSTRUXTI( <br />1. Cut, fold up & temporarily secure <br />resistive barrier above header to allow for <br />flashing installation <br />2. Self -adhered flashing plus head flashing under <br />weather resistive barrier <br />3. Fold weather resistive barrier back over head <br />flashing and seal with tape <br />SELF -ADHERED FLASHING Scale: NTS <br />FLANGED WINDOW <br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER <br />S <br />DO NO" <br />BOTTO <br />FLANGE <br />SELF -ADHERED FLASHING <br />HALF ROUND WINDOW <br />THESE DETAILS ARE GENERIC AND <br />MEANT TO SHOW GENERAL FLASHING <br />AND WATERPROOFING METHODS TO <br />BE USED. <br />3/8" CEMENT <br />PLASTER <br />12 MIL DRYLOK <br />CMU - MASONRY BLOCK <br />EXTREME <br />WINDOW <br />FASTENER <br />1)SEALANT AT <br />4 SEALANT JOINT <br />WINDOW BUCK TO <br />OUTSIDE EDGE OF <br />'' <br />MASONRY <br />WINDOW BUCK <br />c <br />' <br />2) SEALANT JOINT <br />5) SEALANT FROM <br />INSIDE EDGE OF <br />WINDOW FRAME <br />WINDOW BUCK <br />ACROSS WINDOW BUCK . <br />AND EXTEND TO <br />WINDOW FRAME <br />MASONRY <br />ATTACHED <br />PER CODE <br />6) TOOLED SEALANT <br />REQUIREMENTS <br />BEAD BRIDGING <br />CLADDING AND WINDOW <br />FRAME <br />3) SEALANT WINDOW FRAME T( <br />WINDOW BUCK ALL THE WAY <br />AROUND, INCLUDING SILL. <br />SCS 0605 CMU INSTALLATION 6 POINT BUCK AND <br />FENESTRATION INSTALLATION AND INTERFACE <br />WEATHER RESISTIVE <br />BARRIER <br />WINDOW UNIT FLASHING REQUIREMENTS <br />DOOR ROUGH OPENING <br />SLOPE <br />0.3 in: 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall <br />- 3/4%1" BEAD OF CONSTR. (0.6 cm: 30.5 cm) include flashing as described in Section R703.4. <br />ADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING <br />THRESHOLD OF DOOR AND <br />RETURN UP JAMB 6". USE LIQUID R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of <br />NAIL BRAND OR EQUAL WEATHER . EXTERIOR <br />within the wall assembly by providing awater-resistant barrier behind the exterior cladding as required by Section R703.2 and a means <br />PROOF CAULKING CEMT. FIN. water <br />SELF -ADHERED FLASHING � BUILDING PAPER of draining to the exterior water that penetrates the exterior cladding. <br />WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or <br />SUBFLOOR %' other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls No 15 asphalt felt shall be applied <br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The <br />RIM JOIST / No.15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and <br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1. <br />v <br />1 R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over <br />wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade <br />2 O D paper. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers. <br />SELF -ADHERED FLASHING <br />1 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER 1 Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance <br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening, <br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT substantially nonwater-absorbing layer or designed drainage space. <br />RUBBERIZED <br />INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE <br />FLASHING JAMB&HEAD THROUGH SELF -ADHERED R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be <br />FLANGED WINDOW FLASHING SELF -ADHERED FLASHING --,- <br />LASHING applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied <br />(SEE DETAIL WP01) membranes used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to <br />SCORED prevent the entry of water into the wall cavity or penetration of water to the building structural framing components. <br />RELEASE PAPER Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with <br />SELF -ADHERED FLASHING, �'� (BEFORE FOLDING, SCORE the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and <br />EXPOSE <br />EXTEND A MINIMUM 6" RELEASE <br />ESIVEASSAPER OHOWN) contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as <br />BOTTOM of FROM flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved fleshings <br />THRESHOLD shall be installed at the following locations: <br />1.1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall <br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible fleshings <br />2 shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the <br />following: <br />5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration <br />4 manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details <br />1 6 are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or <br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for <br />2 7 subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides. <br />1.2 1.2. In accordance with the flashing design or method of a registered design professional. <br />SELF -ADHERED FLASHING 1.3 1.3. In accordance with other approved methods. <br />INSIDE CORNER , 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400. <br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under <br />stucco copings. <br />Ground 3.3.Under and at the ends of masonry, wood or metal copings and sills. <br />4. 4. Continuously above all projecting wood trim. <br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. <br />1 6.6.At wall and roof intersections. <br />Water Resistant Barrier <br />7.7.At built-in autters. <br />JAMB, SILL AND HEAD DETAIL Lath <br />APPROVED SHEATHING SELF -ADHERED FLASHINGSheathing <br />APPROVED HOUSEWRAP PATCH <br />STRUCTALATH TWIN TRACK 2.5 Stucco <br />3/4" CEMENT PLASTER <br />„12 MIL (min) DRYLOK EXTREME ° ° a aN <br />° ° tf <br />° <br />APPROVED FLASHING TAPE ��I �'•,,I�DOUBLE3 <br />° <br />W" SEALANT SOCKET WITH l { t ( JOIST <br />TOOLED APPROVED SEALANT I ° <br />SINGLE I ° ° <br />`\ WOOD BEAM ° <br />q JOIST BELOW Foundation Wall <br />1 SELF -ADHERED FLASHING ° ° <br />SELF -ADHERED FLASHING 1 e ° ° <br />° <br />°z..... L a <br />_ 3" MIN <br />SELF -ADHERED SELF -ADHERED 4 <br />FLASHING FLASHING <br />20 5 <br />SCS 06_02 WINDOW FIN INTERFACE WITH SELF -ADHERED FLASHING SELF -ADHERED FLASHING , EXTRUDED SHOULDER DECK JOIST , OUTSIDE CORNER FOUNDATION WEEP SCREED <br />SELF -ADHERED FLASHING 2x FRAMEWALL - - - - - - -1 <br />I� STRIP OF LEGEND <br />PRODUCTSDETAILS TILE FINISH i SELF ADHERED FLASHING (SAF) - - - - <br />I- DRAINAGE PLANE WRB DRAINAGE PLANE (DP) WEATHER RESISTANT <br />W I I I BARRIER (WRB) <br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO C ! BOND BREAK WRB BOND BREAK WEATHER RESISTANT BARRIER- <br />1/2" DUROCK > I I SELF FURRING (SF) LATH <br />PER THE FBC RESIDENTIAL 7TH EDITION (2020) <br />I PLASTER ACCESSORY <br />I SF LATH SHEATHING, 'OSB', PLYWOOD, DENSGLASS <br />1'4' PER PLAN <br />Detail Instructions 10 I WRAP OP WRB ONTO <br />1-0 PER PLAN d I I THE VERTICAL <br />Refer to the number marked asRinstructions <br />In each detail that corresponds to the l I SURFACE TO TOP OF <br />numbered items in the list below: I I FLANGE AS AN AIR <br />II BARRIER <br />i <br />1. Install self -adhered flashing in order as shown by numbers 8" CMU SLOPE I I I 3-1/2" INCH FLANGE <br />2. Install flashing and weather resistive barrier to form water shedding <br />laps 4" OR 8" CMU <br />(PER SEAT DEPTH) <br />3. Self -adhered flashing can be substituted for building paper __ __ z z I STRUCTURAL FRAMING <br />4. Split the release paper using the ripcord (Split release on demand, I� ° g <br />FILL WITH GROUT � 8 0_ d �� �� ;i . STRUCTURAL SHEATHING <br />embedded in the adhesive layer) - for ease of installation and to m THIS GAP IS A RESULT OF <br />minimize scoring cuts ° d uJ PLASTER STOP <br />NATURAL SHRINKAGE, i . STRIP OF SAF <br />5. Remove all release paper per standard installation instructions and ° o = � �- - - - - - - - - - DO NOT SEAL. _ ---- --- <br />CONTINUOUS BACKER DRAINAGE PLANE WRB <br />adhere to substrate using a square piece of flashing material (6" x 6" 0 ROD & SEALANT I . <br />U DRIP SCREED PLASTIC Minimum 1--�_ ° a W Lu ACCESSORY I <br />BOND BREAK WRB <br />SLOPED MUD BED _ _ <br />6. Fold as shown by arrows- a a° ° ¢ I 1 SF LATH <br />LU <br />7. Angle of corner may vary, adjust folding of the flashing accordingly to N ° ° U) o <br />fit tight to corner VINYL SHOWER PAN t a ° ° ° = A I I I <br />8. Mechanically fasten as necessary H ° (� ' e---------= 1=___---------------�ii I <br />-------- ------------- <br />-------------- <br />SLOPE <br />° 1 1 <br />° PLASTER STOP A <br />a Q CONTINUOUS BACKER ROD <br />4 a & SEALANT <br />a <br />/I CEMENTITIOUS FINISH <br />SHOWER SEAT <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK - SECTION A <br />EXTERIOR SHEATHING <br />3/4"-1" BEAD OF CONSTR. <br />ADHESIVE TO BE APPLIED UNDER <br />THRESHOLD OF DOOR AND RETURN <br />UP JAMB 6". USE LIQUID NAIL BRAND <br />OR EQUAL WEATHER PROOF CAULKING <br />SECTION -A (SEE DETAIL WP02) <br />4SHING <br />SELF -ADHERED FLASHING <br />i <br />� <br />CO <br />SEAL TOPS OF JOISTS <br />UNDER DECKING <br />(SEE DETAIL WP07) <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK <br />SOFFIT/CANTILEVER <br />Cement Plaster <br />in accordance <br />with ASTMC926 <br />over wood 2nd <br />floor <br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL <br />FLASHING AND WATERPROOFING METHODS TO BE USED. <br />Cement <br />Plaster <br />over block <br />1st floor <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />- Felt backed metal <br />lathe in accordance <br />with ASTM C1063 <br />Building Paper <br />-7/16" O.S.B. <br />sheathing <br />- Metal <br />Flashing <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />Maintain <br />Bottom of <br />Weep Screed <br />1 1/2"to 2" <br />Above Roof <br />Sheathing <br />Note: <br />The building paper and metal lath must be <br />installed over the top of the weep screed. <br />WEEP SCREED DETAIL <br />SCALE: NOT TO SCALE <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />Felt backed metal <br />lathe in accordance <br />with ASTM C1063 <br />Building Paper <br />7/16" O.S.B. <br />sheathing <br />-Stampede or similar <br />cauk bottom <br />joint only <br />Weep Screed <br />Installed As Per <br />Manufact, Specs. <br />1/2" Cementitious <br />Decorative Finish <br />All inside and <br />outside corner will <br />need to be miter <br />cut and caulked all <br />butt joints need to <br />becaulked using <br />Stampede or sim. <br />caulk for all <br />C <br />Cw� <br />� <br />c <br />R <br />as a <br />C2 <br />Q� o <br />c cc v N <br />Vf -p CV <br />fr O C. <br />4 CV Y <br />3 °3 d <br />a� <br />as c <br />� r <br />z 3 co <br />ao y o� :ra <br />• v a� <br />CU c ca <br />2 <br />CV <br />CV <br />0 <br />C'V <br />0 <br />To the best of the Engineer's knowledge, information and belief, <br />the structural <br />plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential <br />7th Edition. Engineers signature and seal is only for <br />the structural <br />engineering portions of the drawing pages bearing <br />Engineers <br />signature and seal. <br />W <br />Q <br />E <br />0 <br />ON R <br />0 <br />N CU o <br />c0 N r <br />N <br />7 u7 ;-D <br />cn(Nr� 4 <br />M <br />aS m v 4t " <br />W <br />LL a <br />,n <br />Z <br />_J HE <br />( O W a- 2 <br />(� co O <br />Om <br />ZC0 ILW <br />w <br />N Z Q J <br />N OU <br />Z <br />N <br />W <br />❑ ❑ <br />N M <br />0 0 <br />o <br />z � N <br />Q o S <br />J - <br />N <br />M <br />z <br />v <br />�N <br />CD o <br />w <br />4-1 <br />�' <br />OLL, <br />o <br />vas <br />v <br />8 <br />U o <br />co <br />Fold <br />N <br />.4 <br />ti <br />W <br />co <br />cozz <br />M <br />J <br />o <br />Z <br />J <br />n E <br />E o <br />oo <br />w= <br />� <br />¢� <br />z© <br />V <br />@ <br />Q 0 <br />20 <br />0¢ <br />0 O <br />o< <br />O E <br />N <br />�0 <br />a o <br />az <br />WW <br />m <br />c0 <br />oY <br />o <br />of <br />� J <br /><w <br />2,0 <br />aw <br />22 <br />Z� <br />0 <br />U <br />CL <br />¢ <br />az <br />T <br />o0 <br />F� <br />w¢ <br />�a <br />o <br />O <br />d <br />I <br />a <br />o3 <br />0 CV <br />U-) <br />co <br />_ <br />rT <br />c� <br />O <br />> <br />(D <br />LO <br />0 <br />-c <br />N <br />r <br />co O <br />O <br />O <br />_M <br />M <br />00 <br />U) m <br />a <br />T <br />N <br />Q <br />+ <br />O <br />Q0 N <br />LA-) <br />00 0 <br />C-0 <br />o <br />N N <br />QL <br />rn L000 <br />CT)N <br />Cfl <br />ro <br />T <br />p <br />o <br />E <br />C <br />CM <br />N <br />z <br />Z <br />E <br />m <br />ca <br />a <br />v _1 <br />Q C) I <br />_J <br />JOB <br />NO: 22-09484-09479 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />W P <br />