Laserfiche WebLink
INSTALL b' SELF -ADHERING <br />MEMBRANE R-AS14MG OVER <br />TOP, SIDE(S) AND BOTTOM <br />FLANGES OF NON -MOVABLE <br />FRAME OF THE EXHAUST. <br />SEr&OCE OF FLAS14MG TO BE: <br />L BOTTOM. 2. SIDES- 3. TOP <br />VENT CAP IS TO BE SET IN BED <br />�:..;.r: <br />• <br />OF SEALANT AT TOP AND <br />-_. <br />SIDES ONLY. SEALANT IS TO BE <br />TOOLED SO AS TO DEFLECT <br />WATER AWAY FROM JOINTS. <br />�X^ <br />E-Z BEAD ALL AROUND <br />VENT-APPLY SEALANT ALL <br />1 <br />iX. <br />JOINTS AND INTERSECTIONS <br />APPLY SEALANT AT PERIMETER OF <br />BACKER ROD <br />i � <br />NON -MOVABLE FRAME AND STUCCO <br />ON ALL SIDES, Ys' CAULKING • JOINT <br />I <br />I <br />ALL AROUND <br />PER SECTION R703.7 <br />Edador 1161111ing and plastaft <br />BACKER ROD <br />I <br />Exterior use of portland cement plaster <br />shall comply with the application <br />'.x. <br />requirements of ASTM C 926-18b. <br />1 <br />(X <br />Installation of exterior lathing and framing <br />1r��IXI <br />�. <br />shall comply with ASTM C 1063-19a, <br />or ASTM 1787. <br />WIRE, LAYER -1,. <br />I` <br />STUCCO WRAP <br />- • <br />HOODED VENT <br />THICK 3 COAT CEMENT <br />I, <br />PLASTER <br />METAL LATH <br />WRB LAYER 4, FORTIFIBER <br />BUILDING PAPER <br />UJOOD SHEATHING <br />DRYER VENT <br />(FRAME) <br />WOOD SHEATHING <br />LAYER I, <br />STUCCO WRAP <br />LA___._ <br />IFIBER <br />BUILDING PAPER <br />wOov <br />CONSTUCTION <br />—METAL LATH <br />v Cm VINYL CASING BEAD <br />W RAISED BAND <br />NI' TO V MID -WALL <br />UJEEP 25["�FI'] <br />6' WIDE STRIP SELF <br />ADHESIVE FLASHING, CLEAN <br />MASONRY BEFORE APPLYING <br />Z FLASHING <br />STONE VENEER <br />OVER SCRATCH COAT <br />HORIZONTAL WEEP SCREED <br />W/STONE VENEER <br />(FRAME TO BLOCKI <br />LEGEND <br />DRAINAGE PLANE (WRB <br />LAYER 01, STUCCO WRAP) <br />WRB LAYER 02 (FORTIFIBER ------ <br />BUILDING PAPER) <br />METAL LATH x—x—x—x <br />STUCCO <br />WOOD OR l/16' ZIP WALL <br />SHEATHING <br />SELF-ADHESIVE FLASHING — — — — — <br />NOTE: <br />METAL LATH: LATH TO BE PER SECTION <br />R-103.1.1 / ASTM C-64-1-14a, MIN. 2.5 LBS. <br />PER SQ. YARD (UTILITY OR NOMINAL <br />LATH DOES NOT MEET SPECIFICATIONS) <br />FINISH <br />W SELF ADHESIVE <br />OVER TOP t SIDES <br />FLASHING <br />UNIT <br />PIREMANUF. DRYER <br />VENT CAP (SET IN <br />CONT. SEALANT) <br />SEALANT • <br />TOP 4 SIDES <br />6 DRYER VENT (BLOCK) <br />BUILDING PAPER <br />OVER 'QUICK <br />FLASH' <br />PIPE TWROUGN / <br />WALL <br />I <br />6' SELF ADHESIVE — <br />FLASHING (INSTALL <br />PER MANLP. SPECS) <br />BUILDING PAPER <br />UNDER 'QUICK FLASH' <br />A VENT PENETRATION <br />SCALE: KTS. <br />ELEC. METEF <br />VERIFY LO <br />.2riCH I C/ RCG_C I VC <br />STUCCO SCRATCH COAT <br />d 1 COAT OF PAINT W/BACK- <br />ROLL PRIOR TO <br />ELEC. METER INSTALLATION <br />I <br />METER FIELD <br />VERIFY LOCATION <br />CONSTRUCTION <br />WOOD SHEATHING <br />WR8 LAYER 'I, <br />STUCCO WRAP <br />WRB LAYER 02, FORTIFIBER <br />BUILDING PAPER <br />J' THICK 3 COAT CEMENT <br />PLASTER <br />Ye' TO Ye' MID -WALL <br />WEEP SCREED <br />�6' SELF-ADHESIVE <br />FLASHING <br />WOOD FRAMED <br />- ' 4::� <br />WALL <br />HORIZONTAL WEEP SCREED <br />( FRAME TO FRAME) <br />APPLY STUCCO SCRATCH COAT <br />AND ONE (1) LAYER OF PAINT <br />PRIOR TO INSTALLING ELEC. <br />METER <br />CAVITY TO BE FILLED <br />WITH RIGID POLYMERIC <br />ISOCYANOTE-POLYBLEND FOAM <br />-('GREAT STUFF' OR SIMILAR) <br />APPLY A SILICON <br />BASE SEALANT AT POINT <br />THAT ELEC. WIRE PENETRATES <br />PROVIDE STUCCO SCRATCH <br />COAT LARGER THAN THE ELEC. <br />METER CAN OR METER CAN <br />COMBO OR METER CAN AND <br />DISCONNECT <br />O ELECTRICAL CONDUIT <br />PENETRATION <br />CUT OPENING IN <br />APPROVED HOUSEWRAP <br />FOR BOX INSTALLATION <br />WRB LAYER 01, <br />STUCCO WRAP <br />WOOD SHEA <br />APPROVED <br />HOUSEWRAP <br />BELOW <br />CUT SUCH THAT—.....- 9 <br />NO MEMBRANE <br />ENTERS BOX, <br />APPLY TO FACE <br />EDGE <br />WOOD SHEATHING <br />LAYER 'I, <br />STUCCO- WRAP <br />LAYER 4, FORTIFIBER <br />BUILDING PAPER <br />METAL LATH <br />UJOOD 0"TRUCTION �y�FMISH • DD <br />FASTEN TO WOOD STRUCTURAL <br />MEMBER • T OC. MAX <br />a <br />IEETPO SCM L <br />6' WIDE STRIP SELF <br />ADHESIVE FLASHING, CLEAN <br />MASONRY BEFORE APPLYING <br />V "41814 • MASG%Wr <br />HORIZONTAL WEEP SCREED <br />(FRAME TO BLOCK) <br />APPLY E-Z BEAD <br />OVER 6m MIN <br />GRADE 'D' <br />FELT -PROVIDE <br />SEALANT AT ALL <br />JOINTS AND <br />INTERSECTIONS <br />STEP 03 <br />P3, <br />WRB LAYER *I, <br />STUCCO WRAP <br />WRB LAYER 61, <br />STUCCO WRAP <br />APPLY b0 MIN <br />SELF -ADHERING <br />GRADE 'D' FELT <br />MEMBRANE FLASHING <br />OVER <br />SELF -ADHERING <br />FLASHING OVER <br />APIROVED <br />L t <br />i <br />HOUSEWRAP <br />. <br />WRB LAYER 02, FORTIFIBER <br />IBUILDING PAPER <br />STEP <br />04 <br />ELASTOMERIC <br />COATING OVER <br />STUCCO/ C.V. FINISH <br />(SEE TYPICAL WALL <br />SECTION) <br />METAL LATH MA <br />STEP 05 STEP #� <br />l 9) ELECTRICAL RECEPTACLE <br />A E C N 1 T E C T I <br />6 <br />Groui In <br />c. <br />41 N. RONALD REAGAN BL\ <br />LONGWOOD, FL 32750 <br />PH: 407-774-6078 <br />FAX: 407-774-4078 <br />www.a bdeslgngroup.com <br />AA #: 0003325 <br />d <br />z <br />�l <br />L4 <br />to <br />0 <br />h <br />0 <br />F <br />9uBDIV. Ae LOT: <br />SILVERADO <br />LOT #22 <br />BLK #14 <br />PROJECT# <br />03719.001-22141 <br />MODEIU <br />"2045-UNTANA" <br />GARAGE 9MING: <br />RIGHT <br />PAGE: <br />WALL <br />ASSEMBLY <br />DETAILS <br />50 MPH XP. <br />