38233 Daughtery Rd - Laserfiche WebLink

Browse Search

8 0 N INSTALL APPROXIMATLY 12" ABOVE FINISHED FLOOR — EXISTING FLOOR WATER SERVICE INTO BUILDING 2 PIECE FULL PORT BRASS BALL VALVE INCOMING WATER SERVICE FROM BELOW GRADE TO 5'-0" OUTSIDE OF BUILDING (END OF PLUMBING CONTRACT) CREFER TO CIVIL DRAWINGS FOR) CONTINUATION OF PIPING / y� y�\��\ \�� WATERTIGHT PIPE SLEEVE MAIN BUILDING SHUT-OFF VALVENOT TO SCALE I RULE 1: BRANCH LINES OF 20 FEET OR LESS. THE HAMMER ARRESTOR SHOULD BE PLACED AT THE END OF THE BRANCH LINE BETWEEN THE LAST TWO FIXTURES. RULE 2: BRANCH LINES OVER 20 FEET. AN ADDITIONAL HAMMER ARRESTOR (Y) SHOULD BE PLACED AS SHOWN (BELOW). THE ADDITIONAL UNIT PLACED AT THE MIDPOINT OF THE RUN LONGER THAN 20 FEET. THE SUM OF THE FIXTURE UNIT RATINGS OF (X) AND (Y) COMBINED, SHOULD BE EQUAL TO OR GREATER THAN THE DEMAND OF ALL BRANCHES. HAMMER ARRESTOR MAIN LINE or RULE 1 BRANCH LINE UNDER 20 FEET — ARRESTOR STOR ARRESTOR MAIN LINE RULE 2 Y X BRANCH LINE OVER 20 FEET — WATER HAMMER ARRESTOR DETAIL NOT TO SCALE HOT WATER FROM BALL VALVE WATER HEATERS (NORMALLY CLOSED) TEMPERED (HOT) WATER TO ,",,-BUILDING (TEMP. TO BE SET AS PER FULL SIZE IOWNER'S REQUIREMENTS, 110'F) BY-PASS 3 F DIELECTRIC TRIC ID OEI HEAT TRAP (28" DROP) /— BALL VALVE (TYP) FINISHED WALL STAINLESS STEEL FLUSH COVER PLATE WITH SECURING SCREW CLEANOUT TEE WALL CLEANOUT DETAILNOT TO SCALE COUNTERTOP \ ..._ \ \ \ \ \ \ \ \ \ \ 3/8" COLD WATER \ ' SUPPLY FROM SINK / / / / / / / / / / TOE CLEARANCE REFRIGERATOR METAL POWERED COATED 20 GAUGE RECESSED MOUNTED VALVE BOX 1/4 TURN VALVE WITH HAMMER _r • ARRESTOR THRU WALL EXPOSED IN -LINE AQUA -PURE FILTER MODEL AP717 .5 GPM FLOW IN CABINETRY EXPOSED IN -LINE BACKFLOW PREVENTER WATTS SERIES 7 REFRIGERATOR ICE MAKER CONNECTION DETAIL C� COLD WATER FROM MAIN SUPPLY STRAINER BALANCING NOTES CHECK VALVE 1. WITH BALL VALVE CLOSED, SET MIXING VALVE TO DESIRED TEMPERATURE WITH WATER FLOWING FROM TEMPERED WATER LINE. 2. AFTER OBTAINING DESIRED TEMPERATURE, STOP THE WATER FLOW. 3. CRACK THE BALL VALVE SO THAT A SMALL AMOUNT OF WATER IS RETURNED TO THE HOT WATER SOURCE. THIS WILL ALLOW THE MIXING VALVE TO MAINTAIN THE SET TEMPERATURE DURING PERIODS OF NO DRAW. 4. OBSERVE THE TEMPERATURE ON THE DISCHARGE OF THE MIXING VALVE. IF THE TEMPERATURE INCREASES ABOVE THE SETTING IN STEP 1, CLOSE THE BALL VALVE SLIGHTLY OR IF THE TEMPERATURE DECREASES, OPEN IT SLIGHTLY. 5. REMOVE BALL VALVE HANDLE AFTER SYSTEM BALANCED AND TURN OVER TO OWNER WITH BALANCING INSTRUCTIONS. WALL MOUNTED THERMOSTATIC WATER CONTROLLER DETAIL NOT TO �[ EXTERIO1 BRICK FA EXTERIOR RECESSED WALL BOX 18"-2 FROM RECESSED CONC. WALL BOX FRONT EXISTING FLOOR NOT TO SCALE System No. W—L-1054 F Ratings — 1 and 2 Hr (See Items 1 and 3) T Rating — 0 Hr L Rating At Ambient — Less Than 1 CFM/Sq Ft L Rating At 400 F — 4 CFM/Sq Ft SECTION a -a 10R 2 HOUR FIRE RATE WALL PIPI 1. Wall Assembly -- The 1 or 2 hr fire -rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner specified in the individual U300 or U400 Series Wall and Partition Designs in the UL Fire Resistance Directory and shall include the following construction features: A. Studs -- Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom 2 by 4 in. lumber spaced 16 in. OC. Steel studs to be min 2-1/2 in. wide and spaced max 24 in. OC. When steel studs are used and the diam of opening exceeds the width of stud cavity, the opening shall be framed on all sides using lengths of steel stud installed between the vertical studs and screw -attached to the steel studs at each end. The framed opening in the wall shall be 4 to 6 in. wider and 4 to 6 in. higher than the diam of the penetrating item such that, when the penetrating item is installed in the opening, a 2 to 3 in. clearance is present between the penetrating item and the framing on all four sides. B. Gypsum Board* -- 5/8 in. thick, 4 ft wide with square or tapered edges. The gypsum board type, thickness, number of layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire Resistance Directory. Max diam of opening is 32-1/4 in. for steel stud walls. Max diam of opening is 14-1/2 in. for wood stud walls. The F Rating of the firestop system is equal to the fire rating of the wall assembly. 2. Through -Penetrants -- One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop system. The annular space shall be min 0 in. to max 2-1/4 in. Pipe may be installed with continuous point contact. Pipe, conduit or tubing may be installed at an angle not greater than 45 degrees from perpendicular. Pipe, conduit or tubing to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes, conduits or tubing may be used: A. Steel Pipe -- Nom 30 in diam (or smaller) Schedule 10 (or heavier) steel pipe. B. Iron Pipe -- Nom 30 in. diam (or smaller) cast or ductile iron pipe. C. Conduit -- Nom 4 in diam (or smaller) steel electrical metallic tubing or 6 in. diam steel conduit. D. Copper Tubing -- Nom 6 in. diam (or smaller) Type L (or heavier) copper tubing. E. Copper Pipe -- Nom 6 in. diam (or smaller) regular (or heavier) copper pipe. 3. Fill, Void or Cavity Material* -- Sealant -- Min 5/8 in. thickness of fill material applied within the annulus, flush with both surfaces of wall. At the point or continuous contact locations between pipe and wall, a min 1/2 in. diam bead of fill material shall be applied at the pipe wall interface on both surfaces of wall. (HILTI CONSTRUCTION CHEMICALS, DIV OF HILTI INC -- FS-One Sealant) *Bearing the UL Classification Mark NG P'ENTRATION DETAIL FLOOR DRAIN WITH TRAP PRIMER CONNECTION EXISTING FLOOR SLAB —t—�=ij=-1---- D NON -SHRINK GROUT DEEP SEAL P TRAP FLOOR DRAIN DETAIL NOT TO SCALE 3/4 "WATER SUPPLY =ROM CEILING "YPSUM WALL METAL STUD � EXTERIOR WALL HYDRANT DETAIL„o„oIC„EJ n nnn TRAP GUARD DETAIL EXISTING FLOOR SLAB n C-- D n D I /i RhM FLOOR SINK DETAIL TRAP (TYPICAL) NOT TO SCALE FLOOR SINK WITH REMOVABLE GRATE AND SEDIMENT BUCKET FLUSH WITH FLOOR D �D ° ° D n D ° -SHRINK GROUT DEEP SEAL P TRAP NOT TO SCALE 0wARD4fo� ��CENSF,G,92r.�� 40193 r �s •4 RIB, OMhM Project No. 151010 NOT FOR CONSTRUCTION P5,0 Z:\BH_PK Architects\151010 — FH (Zephyrhills) — Wellness Center\Des1gn\151010_P5.0.dwg Monday, February 14, 2011 3:34:45 PM Shawn Jeffrey PAW am aDA 33619 2 1-SM Z4t-em V= 02015 BH/PK Architects, Inc.