Laserfiche WebLink
4- <br />Li <br />2 <br />a <br />0 <br />0 <br />0 <br />IN <br />0 <br />cv <br />0 <br />Ln <br />J <br />n <br />iL <br />O <br />PLAIN END OUTLET <br />2" VENT <br />I <br />LAVATORY <br />GRADE <br />I <br />FAUCET <br />I <br />\ <br />�j <br />5 % - <br />MAXLINE <br />VALVE <br />w <br />� <br />I <br />HOT <br />4 <br />VALVE VALVE <br />20" X 24" LONG <br />I <br />Ln <br />WATER <br />TANK, <br />HEATER, TEMPERED <br />ETC. HOT SUPPLY <br />PEA GRAVEL <br />MAIN HOT SUPPLY <br />04 <br />I I <br />COLD SUPPLY <br />\ <br />I <br />SINK OR LAVATORY RIM <br />NOTES: <br />/ <br />\ <br />1. INSTALL PER MANUFACTURER'S WRITTEN INSTRUCTIONS <br />2. SET TEMPERATURE TO 1100 MAXIMUM PER FBC. <br />NOTE: HANDLES TO BE POSITIONED AT AN 180' ANGLE IN THE <br />CLOSED POSITION. <br />DRY WELL DETAIL <br />TYPICAL GOOSENECK INSTALLATION <br />MIXING VALVE PIPING AT FAUCETS <br />WOOD TR SS STRUCTURAL SUPPORT SYSTEM. <br />HANGER ROD. PROVIDE A SECTION OF HIGH <br />COMPRESSION STRENGTH <br />.'�: o .:a: 'o, °:. .. c::'a c.e ..:a:.; ..:° .. ..:•o:•-a. :.6:.. o ..: <br />INSULATION AT EACH HANGER <br />POINT. INSULATION MAY BE <br />PHILLIPS CONCRETE FASTENER <br />HALF ROUND OR FULL ROUND <br />AND EXTEND 2"BEYOND <br />GALVANIZED SHIELD EACH WAY. <br />I.T.T. GRINNELL (RED HEAD) <br />THERMAL EXPANSION TANK <br />PROVIDE 3/8" DIAMETER <br />WATTS#DET-12-M1,ANS1/NSFG <br />THREADED ROD WITH <br />4.5GAL,1.8GAL ACCEPTANCE <br />WASHERS AND DOUBLE <br />ALL THREAD- <br />SUPPORT FROM STRUCTURE <br />NUTS AT EACH END. <br />i <br />eC <br />HANGER ROD <br />HEAT TRAPS <br />ROUTE ROD FROM <br />CHANNEL BELOW WATER <br />GALVANIZED <br />(OMIT IF HEAT TRAP IS AN <br />HEATER UP TO FASTENERS <br />SHIELD <br />INTEGRAL PART OF HEATER) <br />ABOVE. (TYPICAL OF 4). <br />HOT WATER TO FIXTURES <br />COLD WATER SUPPLY <br />AS SHOWN ON PLANS. <br />TO WATER HEATERU) <br />i <br />PIPE HANGER RING <br />THERMOMETER - T <br />VACUUM RELIEF VALVE <br />i <br />4- <br />I.T.T. GRINNELL FIG.69 <br />WATTS #36A OR APPROVED <br />EQUAL <br />PROVIDE FULL PORT BALL <br />UNINSULATED COPPER LINES <br />SHUT-OFF VALVES. <br />PROVIDE A 210A <br />PIPE CLAMPS WITH CUSHIONS <br />PROVIDE PIPE <br />TEMPERATURE AND <br />HANGER "PHD" MANUFACTURING MODEL <br />PIPE HANGER RING PIPE <br />UNIONS DIELECTRIC <br />150 PSI PRESSURE <br />= ROD 2501-2514 _ <br />I.T.T. GRINNELL FIG.260 <br />IF REQUIRED FOR <br />RELIEF VALVE <br />DISSIMILAR METALS._ <br />WITH TEST LEVER <br />SIZED WITH AGA/CGA <br />= _ <br />DRAIN VALVE BY <br />HEATER MAUF CT. <br />TEMPERATURE <br />RATING 107 OVEREAM <br />HEATING INPUT. <br />_ = <br />PIPES 2112 & SMALLER PIPES 3" & LARGER <br />THERMOSTAT AND <br />PRESSURE REGU- <br />-PROVIDE A HARD <br />= = <br />NOTE: 1. PROVIDE COPPER PLATING ON HANGER BETWEEN <br />LATOR FURNISHED <br />COPPER RELIEF <br />VALVE DISCHARGE <br />STEEL AND COPPER WHERE UNINSULATED COPPER <br />WITH WATER HEATER. <br />LINE FULL SIZE OF <br />— — — — — — _IL <br />PIPING IS USED. <br />3/4' PLYWOOD BELOW <br />VALVE OUTLET RUN <br />TO TERMINATE OVER <br />_ U _ u _ u _ U _ d _ U _U— _ _ <br />2. PROVIDE ADDITIONAL HANGERS ON EACH SIDE OF A <br />WATER HEATER DRAIN <br />PAN AS PLATFORM. <br />2' SAFE PAN. <br />- v INSULATED PIPE LINE WITH <br />- METAL CHANNEL STRUT <br />WALL WHERE THE PIPING PENETRATES THE WALL. <br />PIPE CLAMP. PROVIDE <br />2' DEEP STAINLESS <br />PROVIDE 2" CHANNELS <br />� MINIMUM <br />INSULATION SHIELD ON 3" <br />3. ALL INTERIOR HANGERS SHALL BE GALVANIZED <br />STEEL SAFEPAN. <br />OF RUSTPROOFPRIMER <br />NOTES; AND LARGER. <br />INCLUDING THREADED RODS, NUTS AND BOLTS. <br />PROVIDE A DRAIN <br />SF BETWEEN <br />1. TRAPEZE HANGERS SHALL NOT BE USED ON STORM, <br />PAN, RU OVERFLOW <br />THREADED RODS TO <br />SUPPORT WATER HEATER <br />OVERFLOW STORM OR SANITARY PIPING SYSTEMS. <br />4. ALL PLUMBING TRADE ITEMS SHALL BE INDIVIDUALLY <br />LINE AT�X4' SLOPE <br />SAFEPAN. <br />2. PROVIDE ADDITIONAL HANGERS ON EACH SIDE OF A <br />AND RIGIDLY SUPPORTED FROM STRUCTURE ABOVE <br />AND TERMINATE OVER <br />WALL WHERE THE PIPING PENETRATES THE WALL. <br />INDEPENDENT OF ALL OTHER TRADES. (DO NOT HANG <br />ANFLOOR DRAIN WITH WATER HEATER <br />- MAXIMUM <br />3. ALL INTERIOR HANGERS SHALL BE GALVANIZED <br />PLUMBING ITEMS FROM ANOTHER TRADE.) <br />OF 30 GALLON <br />CAPACITY. <br />INCLUDING THREADED RODS, NUTS AND BOLTS. <br />4. ALL PLUMBING TRADE ITEMS SHALL BE INDIVIDUALLY <br />AND RIGIDLY SUPPORTED FROM STRUCTURE ABOVE <br />INDEPENDENT OF ALL OTHER TRADES. (DO NOT HANG <br />PIPING ARRANGEMENT SHOWN IS SCHEMATIC. ADJUST TO SUIT <br />FIELD CONDITIONS. REFER TO ISOMETRIC RISER FOR PIPE SIZES. <br />PLUMBING ITEMS FROM ANOTHER TRADE.) <br />SET HEATER THERMOSTAT AT 120°F. <br />PLATFORM MOUNTED <br />ELECTRIC <br />TRAPEZE PIPE HANGER <br />U.L./F.M. APPROVED CONCRETE <br />WATER HEATER <br />SCALE: - NONE <br />INSERT PIPING HANGER DETAIL <br />N 0 T TO SCA _ <br />MOV <br />rrr� �I <br />E OF <br />' <br />t! <br />Smith <br />Seckman <br />Reid, Inc. <br />600 West Hillsboro, Suite 300 <br />Deerfield Beach, FL 33441 <br />(954)421-1260 <br />FAX: (954) 421-1466 <br />www.ssr-inc.com <br />Firm Certification - EB-0000857 <br />Dennis Davis PE - 58588 <br />John E. Moulder PE - 33200 <br />SSR JOB # 1137001.0 <br />cv <br />COO <br />o� <br />O 2,' <br />q <br />b <br />y F3 <br />y <br />Cn <br />N <br />CIO <br />Cn <br />O <br />C� <br />O <br />LL <br />1 <br />U <br />m <br />U <br />O <br />Cn C'0 <br />_U <br />-�--� 70 <br />Cll � <br />0 <br />Cn <br />O <br />^� CV <br />LL T <br />Project No. 11006,00 <br />P5.1 <br />©2011 BHIPK Architects, Inc. <br />s <br />