|
L �
<br />:)ocuSign Envelope ID: 2879FFE4-64D7-4056-8E51-057CBF46E1EB
<br />Footer
<br />Re -Bar (sized _
<br />according to
<br />foundation plan)
<br />°_mac
<br />G °°
<br />#4 awg CU bare w/ 10' stubbed dl
<br />outside of slab at service o
<br />location. Connect to Tooter steel Lo
<br />w/ (2) ground clamps 5' apart
<br />UFER GROUND DETAIL
<br />N.T.S.
<br />ELECTRICAL RISER DIAGRAM
<br />OPTIONAL OVERHEAD
<br />SERVICE SAME AS 150 = #1 Copper or 2/ 0 Aluminum
<br />UNDERGROUND 150 OR 200 200 = 2 /0 Copper or 4 /0 Aluminum in 2"
<br />AMP SERVICE Conduit.
<br />A/C DISCONNECT
<br />METER MAIN
<br />DISC.
<br />150 OR #12 COPPER TO APPLIANCES AND GFI
<br />I
<br />- - 200 AMP TYPICAL
<br />ELECTRICAL #14 COPPER TO LIGHTS AND OUTLETS
<br />PANEL #10 COPPER TO WATER HEATER
<br />UNDGND #8 COPPER TO RANGE
<br />SERV. BY
<br />POWER CO. #6 COPPER TO HVAC
<br />N.T.S. #4 GROUNDING WIRE WITH CODE APPROVED CLAMP TO EITHER:
<br />A) APPROVED GROUNDING ROD WITH MINIMUM 8' DEPTH
<br />B) BONDED TO CONTINUOUS FOOTING STEEL
<br />INTERSYSTEM BONDING TERMINATION PER NEC 250.94
<br />NOTE:
<br />ELECTRICAL MATERIAL AND INSTALLATIONS SHALL COMPLY WITH APPLICABLE
<br />PROVISIONS OF THE NFPA 70, LOCAL CODES AND LOCAL POWER/UTILITY COMPANY
<br />GENERAL ELECTRICAL NOTES
<br />ALL ELECTRICAL DESIGN AND WORK SHALL BE IN STRICT
<br />COMPLIANCE WITH THE 2017 NATIONAL ELECTRIC CODE
<br />• PER NEC SECTION 210.12 (B) ALL 15A & 20A, 120V
<br />BRANCH CIRCUITS SUPPLYING OUTLETS REQUIRE
<br />AFCI PROTECTION
<br />• CARBON MONOXIDE PROTECTION PER FLORIDA
<br />STATUTES 553.885 (2). TO BE INSTALLED WITHIN 10'
<br />OF EVERY SLEEPING ROOM
<br />• ALL OUTLETS SHOULD BE AFCI PER NEC - U.N.O.
<br />• PER NEC SECTION 210.8(B)(5) ALL 15A & 20A, 15V
<br />RECEPTACLES INSTALLED OUTDOORS MUST BE
<br />GFCI-PROTECTED
<br />• PER NEC SECTION 210.8(B)(5) ALL 15A & 20A, 15V
<br />RECEPTACLES INSTALLED WITHIN 6' OF SINK (IN
<br />NON -DWELLING OCCUPANCIES-i.e. OUTDOOR
<br />SUMMER KITCHENS RECEPTACLES) MUST BE
<br />GFCI-PROTECTED
<br />• PER NEC SECTION 406.8(B)(1) 15A & 20A
<br />RECEPTACLES IN A WET LOCATION MUST BE WITHIN
<br />AN ENCLOSURE THAT IS WEATHERPROOF WHEN AN
<br />ATTACHMENT IS PLUGGED IN AN ALL NON -LOCKING
<br />RECEPTACLES SHALL BE LISTED AS WEATHER
<br />RESISTANT
<br />• PER NEC SECTION 406.11 IN DWELLING UNITS, ALL
<br />15A & 20A, 15V RECEPTACLES SHALL BE LISTED AS
<br />TAMPER -RESISTANT
<br />• PER NEC SECTION 800.156 NO LESS THAN ONE
<br />COMMUNICATION OUTLET SHALL BE INSTALLED
<br />WITHIN EACH DWELLING UNIT
<br />• PER NEC SECTION R314.3 AND R315.1 SMOKE
<br />DETECTORS TO BE INSTALLED INSIDE EACH
<br />SLEEPING AREA
<br />• ALL SMOKE ALARMS SHALL BE LISTED AND LABELED
<br />IN ACCORDANCE WITH UL 217, PER FBC 314.1. GC TO
<br />INSTALL- KIDDE MODEL # 14618A SMOKE ALARM, OR
<br />APPROVED EQUAL
<br />• PROVIDE GAS DROPS AS PER COMMUNITY ONLY
<br />• JUNCTION BOX AT WATER HEATER, RANGE AND/OR
<br />DRYER TO BE 220V IN NON GAS COMMUNITIES, AND
<br />110V IN COMMUNITIES THAT HAVE GAS OPTIONS
<br />PROVIDE APPROPRIATE RECEPTACLE PER
<br />APPLIANCE
<br />• ALL LAMPS SHALL BE HIGH -EFFICACY TO COMPLY
<br />WITH FBC-EC R404.1 - (LOW -VOLTAGE LAMPS
<br />EXCLUDED).
<br />• PER FBC-R M1305.1 A LEVEL WORKING SPACE NOT
<br />LESS THAN 30" DEEP AND 30" WIDE SHALL BE
<br />PROVIDED IN FRONT OF THE CONTROL SIDE OF ANY
<br />APPLIANCE
<br />ABBREVIATIONS LEGEND
<br />ABV
<br />ABOVE
<br />AC
<br />AIR CONDITIONER
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />AHU
<br />AIR HANDLER UNIT
<br />BLK
<br />BLOCK
<br />CABS
<br />CABINETS
<br />CLG
<br />CEILING
<br />CHR
<br />CHAIR RAIL
<br />COFF
<br />COFFERED
<br />COL
<br />COLUMN
<br />COND
<br />CONDENSER
<br />CRN
<br />CROWN MOULDING
<br />CVAC
<br />CENTRAL VACUUM SYSTEM
<br />DBL
<br />DOUBLE
<br />DIAG
<br />DIAGONAL
<br />DR
<br />DOOR
<br />DRY
<br />DRYER
<br />DW
<br />DISHWASHER
<br />EB
<br />EYEBROW
<br />FL
<br />FLOOR LINE (MAT. CHANGE)
<br />FLR
<br />FLOOR
<br />FP
<br />FIREPLACE
<br />FXD
<br />FIXED
<br />FXT
<br />FIXTURE
<br />GLS
<br />GLASS
<br />HB
<br />HOSE BIB
<br />KS
<br />KNEE SPACE
<br />LAV
<br />LAVATORY
<br />LT
<br />LAUNDRY TUB
<br />MRBL
<br />MARBLE
<br />MC
<br />MEDICINE CABINET
<br />MIR
<br />MIRROR
<br />MTL
<br />METAL
<br />OH
<br />OVERHEAD
<br />OPNG
<br />OPENING
<br />OPT
<br />OPTIONAL
<br />R & S
<br />CLOTHES ROD and SHELF
<br />REF
<br />REFRIGERATOR
<br />SD
<br />SOAP DISH
<br />SDLTS
<br />SIDE LIGHTS
<br />SGD
<br />SLIDING GLASS DOOR
<br />SH (2)
<br />SHELVES (QUANTITY)
<br />SHWR
<br />SHOWER
<br />TB
<br />TOWEL BAR
<br />TPH
<br />TOILET PAPER HOLDER
<br />T&S
<br />TUB and SHOWER
<br />TEMP
<br />TEMPERED
<br />TR
<br />TRANSOM
<br />VOL
<br />VOLUME
<br />WC
<br />WATER CLOSET
<br />WD
<br />WOOD
<br />WH
<br />WATER HEATER
<br />WNCT
<br />WAINSCOT
<br />WS
<br />WATER SOFTENER
<br />WASH
<br />WASHER
<br />ROOF NOTES EXTERIOR ELEVATION GENERAL NOTES GENERAL NOTES _
<br />• INSTALL ROOF VENTING PER MFR WRITTEN 0
<br />INSTRUCTIONS PER FBC R806 • FRONT ELEVATIONS BANDING, MOLDING, • ALL CONSTRUCTION SHALL MEET THE LATEST O
<br />COLUMNS AND TRIM SHALL RECEIVE A SAND EDITION OF CODES ADOPTED BY THE LOCAL
<br />FINISH. SEE ELEVATION FOR DEPTH OR RAISED GOVERNING AGENCIES Op
<br />• ALL OVERHANG DIMENSIONS ARE TO EDGE OF 0RAFTER. REFERENCE WALL SECTIONS/DETAILS BANDING APES
<br />FOR ALL OVERHANGS NOT DIMENSIONED. • PER FBC R302.5 NO OPENINGS FROM A PRIVATE
<br />• SIDE AND REAR ELEVATIONS BANDING AROUND GARAGE ARE PERMITTED DIRECTLY INTO SLEEPING N 0
<br />WINDOWS AND DOORS MAY BE OPTIONAL PER O 0)
<br />• ALL UNDERLAYMENT MUST BE INSTALLED IN COMMUNITY SPECS - SEE COMMUNITY AREAS, ALL OPENINGS SHALL HAVE SOLID WOOD, � '5<'
<br />COMPLIANCE WITH FBC R905.1.1 SPECIFICATIONS OR CONSULT THE INSULATED STEEL OR 20 MIN. FIRE RATED DOORS rn N
<br />CONSTRUCTION MANAGER. ALL BANDING SHALL NOT LESS THAN 1-3/8 INCHES THICKNESS, EQUIPPED t6
<br />• EACH 4' OFF RIDGE VENT REQUIRES (1) 46" x 3" CUT RECEIVE A SAND FINISH WITH A SELF CLOSING DEVICE. ALL DUCTS IN THE
<br />OUT IN ROOF SHEATHING PER MFR WRITTEN GARAGE OR PENETRATING THE WALL OR CEILING
<br />INSTRUCTIONS • ROOF COVERING SEE COMMUNITY SEPARATING THE GARAGE AND DWELLING SHALL BE N
<br />SPECIFICATIONS OR CONSULT THE I c�
<br />CONSTRUCTION MANAGER. SEE STRUCTURAL CONSTRUCTED OF MIN. 26 GA. SHEET METAL, 1 INCH J
<br />SHEETS FOR SHEATHING REQUIREMENTS MINIMUM RIGID CLASS 0 OR 1 DUCT BOARD, OR ILL Z
<br />OTHER APPROVED MATERIAL AND SHALL HAVE NOtds -6
<br />• FLASHING SHALL BE INSTALLED AT WALL AND OPENINGS INTO THE GARAGE w
<br />ROOF INTERSECTIONS, DECK AND WALL
<br />INTERSECTIONS, AT GUTTERS, AT ALL CHANGES IN • PER FBC TABLE R-302.6 GARAGE SHALL BE true
<br />; sin studios
<br />ROOF SLOPE OR DIRECTION, AND AROUND ROOF SEPARATED FROM RESIDENCE AND IT'S ATTIC W/ Z
<br />OPENINGS MIN. 1/2" GYP BOARD ATTACHED IN ACCORDANCE U)
<br />• WINDOW PAN FLASHING SHALL BE IN WITH TABLE R702.3.5. HABITABLE ROOMS SHALL BE U 9000 REGENCY SQUARE BLVD.
<br />ACCORDANCE WITH FBC R703.4 SEPARATED FROM ROOM ABOVE W/ MIN 5/8" TYPE Q SUITE 100, JACKSONVILLE, FL 32211
<br />"X" GYP BOARD, WHERE THE SEPARATION IS A —� p
<br />• WALL HEIGHTS VERIFY ALL BEARING WALL FLOOR -CEILING ASSEMBLY. ANY STRUCTURE t0
<br />HEIGHTS WITH FINAL TRUSS LAYOUTS SUPPORTING THE ASSEMBLY SHALL BE PROTECTED O
<br />W/ MIN 1/2'' GYP BOARD
<br />• LATH PER FBC R703.7.1, LATH AND LATH W
<br />ATTACHMENTS SHALL BE OF • PER FBC R-312.1 PORCHES, BALCONIES OR RAISED
<br />ROOF VENT CALCULATION CORROSION -RESISTANT MATERIALS. EXPANDED �U-H*HO90N* a)
<br />FORMULA: FINISHED FLOOR OR GRADE SHALL HAVE GUARDS
<br />ATTACHED WITH 11/2-INCH-LONG (38 MM), 11 GAGE
<br />NAILS HAVING A 7/16-INCH (11.1 MM) HEAD, OR NOT LESS THAN 36" IN HEIGHT. PER FBC R-312.1.2 > r§ a
<br />1 SQUARE INCH VENT FOR EVERY 300 SQUARE INCHES 7/8-INCHLONG (22.2 MM), 16 GAGE STAPLES, OPEN SIDES OF STAIRS WITH A TOTAL RISE OF
<br />OF CEILING SPACED NOT MORE THAN 6 INCHES (152 MM), OR MORE THAN 30" ABOVE FINISHED FLOOR OR GRADE m�
<br />144 SQ. IN. = 1 SQ. FT. AS OTHERWISE APPROVED W
<br />BLDG. CEILING (SF) x 144 -BLDG (SQ. IN.) ' I SHALL HAVE GUARDS NOT LESS THAN 34" IN HEIGHT �
<br />BLDG. (SO. IN.) / 300 = SQ. IN. OF VENT REQUIRED • PLASTER PER R703.7.2, PLASTERING WITH MEASURED VERTICALLY FROM THE NOSING OF THE
<br />TREADS r
<br />SQ. IN. OF VENT REQUIRED / 2 = 50% AT HIGH AND 50 0 PORTLAND CEMENT PLASTER SHALL BE NOT LESS
<br />AT LOW. THAN THREE COATS WHERE APPLIED OVER METAL W
<br />LATH OR WIRE LATH AND SHALL BE NOT LESS • PER FBC R-312.1.3 REQUIRED GUARDS ON OPEN
<br />o THAN TWO COATS WHERE APPLIED OVER SIDES OF STAIRWAYS, RAISED FLOOR AREAS, N
<br />PER FBC SECTION R806.2: 40 /o MIN, BUT NOT MORE i
<br />THAN 50% OF VENTILATION MUST BE PROVIDED BY MASONRY, CONCRETE, PRESSURE -PRESERVATIVE BALCONIES AND PORCHES SHALL HAVE I Z
<br />VENTILATORS LOCATED NO MORE THAN 3'-0" BELOW TREATED WOOD OR DECAY -RESISTANT WOOD AS INTERMEDIATE RAILS OR ORNAMENTAL CLOSURES w
<br />THE RIDGE OR HIGHEST POINT OF THE SPACE SPECIFIED IN SECTION R317.1 OR GYPSUM WHICH DO NOT ALLOW PASSAGE OF A SPHERE 4" ' (D
<br />BACKING. IF THE PLASTER SURFACE IS LU
<br />COMPLETELY COVERED BY VENEER OR OTHER OR MORE IN DIAMETER
<br />BASIS OF CALCULATION. ("OR EQUAL" ACCEPTABLE) FACING MATERIAL OR IS COMPLETELY O
<br />CONCEALED, PLASTER APPLICATION NEED BE • PER FBC R-308.4.5 GLAZING IN WALLS, ENCLOSURES O
<br />(a) OFF RIDGE VENTS - STAMPCO W/ 36 SQ IN (NFVA) ONLY TWO COATS, PROVIDED THE TOTAL OR FENCES CONTAINING OR FACING HOT TUBS, rn
<br />PER LINEAL FT THICKNESS IS AS SET FORTH IN TABLE R702.1(1).
<br />SPAS, WHIRLPOOLS, SAUNAS, STEAM ROOMS,
<br />ON WOOD -FRAME CONSTRUCTION WITH AN ti
<br />(b) SOFFIT VENTS - GP T3-1/3" FULL VENT PERFORATED ON -GRADE FLOOR SLAB SYSTEM, EXTERIOR BATHTUBS, SHOWERS AND INDOOR OR OUTDOOR L0
<br />W/ 9.19 SQ IN (NFVA) PER LINEAL FT PLASTER SHALL BE APPLIED TO COVER, BUT NOT SWIMMING POOLS WHERE THE BOTTOM EXPOSED ti
<br />EXTEND BELOW, LATH, PAPER AND SCREED. THE EDGE OF THE GLAZING IS LESS THAN 60 INCHES
<br />CALCULATED LINEAL FOOT OF SOFFIT VENT SHALL PROPORTION OF AGGREGATE TO CEMENTITIOUS MEASURED VERTICALLY ABOVE ANY STANDING OR Z
<br />NOT INCLUDE NON -VENTED FIRE RATED SOFFIT
<br />MATERIALS SHALL BE AS SET FORTH IN TABLE WALKING SURFACE, SHALL BE CONSIDERED A
<br />I I
<br />Uj
<br />LOCATED LESS THAN 5' FROM PROPERTY LINE R702.1(3) HAZARDOUS LOCATION, G.C. TO VERIFY IF rA ^/
<br />HOMEOWNER SELECTS ANY OF THESE ITEMS W L.L
<br />• WEEP SCREED PER R703.7.2.1 A MINIMUM Z
<br />0.019-INCH (0.5 MM) (NO. 26 GALVANIZED SHEET LISTED. IF ANY OF THESE ITEMS LISTED IS U J Z W
<br />GAGE), CORROSION -RESISTANT WEEP SCREED OR INSTALLED, SUCH GLAZING FACING THOSE ITEMS IS D O
<br />PLASTIC WEEP SCREED, WITH A MINIMUM TO BE TEMPERED mUj
<br />VERTICAL ATTACHMENT FLANGE OF 31/2 INCHES
<br />(89 MM) SHALL BE PROVIDED AT OR BELOW THE • PER FBC R312.2, PROVIDE WINDOW FALL w Q
<br />FOUNDATION PLATE LINE ON EXTERIOR STUD PROTECTION IN ACCORDANCE WITH R312.2.1 AND
<br />WALLS IN ACCORDANCE WITH ASTM C926. THE PROT .2 Z O
<br />WEEP SCREED SHALL BE PLACED NOT LESS THANR312(D > 0 Q
<br />4 INCHES (102 MM) ABOVE THE EARTH OR 2 INCHES ZM ' ' 1
<br />(51 MM) ABOVE PAVED AREAS AND SHALL BE OF A • GAS OPT. PER COMMUNITY. VERIFY WITH BLDR w Y■� L1J
<br />LU
<br />TYPE THAT WILL ALLOW TRAPPED WATER TO Q
<br />C.J. =RECOMMENDED MASONRY CONTROL JOINT
<br />DRAIN TO THE EXTERIOR OF THE BUILDING. THE
<br />---
<br />•
<br />WEATHER -RESISTANT BARRIER SHALL LAP THE W
<br />LOCATION ~
<br />ATTACHMENT FLANGE. THE EXTERIOR LATH SHALL o X
<br />COVER AND TERMINATE ON THE ATTACHMENT J
<br />FLANGE OF THE WEEP SCREED • ALL FINISHES, MATERIALS, HOUSEWRAP, WINDOW LL LL
<br />AND DOOR FLASHING, TAPING AND SEALANTS TO BE Z Z
<br />WATER -RESISTIVE BARRIERS PER R703.7.3, INSTALLED PER BUILDER PROVIDED O O
<br />WATER -RESISTIVE BARRIERS SHALL BE INSTALLED SPECIFICATIONS OR MFR WRITTEN INSTRUCTIONS I—
<br />AS REQUIRED IN SECTION R703.2 AND, WHERE Q 0
<br />APPLIED OVER WOOD -BASED SHEATHING, SHALL w w
<br />INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE • ALL FINISH DETAILS & TYPICAL PLAN NOTES O Z
<br />BARRIER WITH A PERFORMANCE AT LEAST PROVIDED BY BUILDER IN ACCORDANCE WITH 0
<br />EQUIVALENT TO TWO LAYERS OF GRADE D PAPER, TYPICAL BUILDER SPECIFICATIONS O w
<br />THE INDIVIDUAL LAYERS SHALL BE INSTALLED
<br />INDEPENDENTLY SUCH THAT EACH LAYER LL
<br />• PROVIDES A SEPARATE CONTINUOUS PLANE AND REFER TO STRUCTURAL ENGINEERING DRAWINGS Q
<br />FOR ALL EXTERIOR ANY FLASHING (INSTALLED IN ACCORDANCE WITH OR WALL STUD SPECIES, SIZES AND Q J
<br />LLI
<br />SECTION R703.4) INTENDED TO DRAIN TO THE SPACING ABBOTT PARK Q
<br />WATER -RESISTIVE BARRIER IS DIRECTED O U
<br />BETWEEN THE LAYERS _j
<br />u- LOT 038-03 0
<br />Q w
<br />U Z
<br />Z
<br />C�
<br />U)
<br />PROJECT NO W
<br />2021.006628 LL
<br />O 0
<br />O
<br />� Z DRAWN: o
<br />U KME
<br />ILL! U-) CHKD,
<br />x
<br />w LLw
<br />w 4
<br />a U
<br />x U)
<br />m Z
<br />o Q
<br />Z
<br />� o
<br />0
<br />w CO
<br />2 U
<br />Q Z
<br />Z 3:
<br />W Q
<br />p 05-17-2021 p
<br />i= w
<br />U REVISIONS: UJI
<br />U_ - - 1-
<br />Q No. Description Date W
<br />W
<br />_ Q
<br />� U
<br />U - W
<br />O
<br />0O O
<br />_ 0
<br />U 0
<br />w
<br />x
<br />W AOOO
<br />a
<br />Q
<br />
|