Laserfiche WebLink
Cut 'X' at each downspout <br />location ad bend tabs down <br />for dowtspout attachment. <br />(3) Pop Rivets <br />One at each side <br />ad one at front.1 <br />Attach strap to Bldg with <br />(1) 1/4- 14 x 7/8' S.D. Screws <br />and (1) Tek 5 S.D. screw at open well <br />Field cut downspout to <br />match gutter bottom argle. <br />(3) 1/4-14 x 7/8' S.D. Screws <br />(One at each side <br />ond one at front <br />L'..•"�'�"ie *•may° <br />(Loo, <br />Clip) Gas Rqd� (Loos' <br />n <br />I-,_ <br />Framed 02mina @ Sidewoll <br />Eave Strut <br />(6) R12x1k4 S.D. Scree <br />(6) #12xQ4 S.D. Screws w/o Washers <br />w/o Washers kin i l 4 <br />jI I fi Door. <br />I Jamb 4-A <br />j I Jamb <br />l i <br />Section 'A' Section 'A' <br />(@ Eave Strut) (@ Girt) <br />Section 'B' <br />Clip) <br />.ter <br />x IV A325 Bolts <br />Nuts t (2) Washers <br />j j / Doo±11 <br />Girt—i (Loose Clip) I Door kmb <br />-Elbow ro—Door pleader <br />Bend strap up at both sides 74 <br />of downspout ord attach with— <br />(1) 1/4-14 x 7/8' S.D. screw at each side. Vzl" A307 Bolts I I (4) k� m x I" -Head Bolts w/ Nuts <br />w/ Nuts I per 1IA2 (2 @ Jamb, 2 @ header) <br />Section 'C' Section 'D' <br />Downspout Details Overhead Door Framed Opening Details <br />J.�v All Conditions <br />REMOVE EXCESS INSULATION FROM ROOF <br />ROLL WHICH EXTEND PAST EAVE STRUT <br />AND FOLD VINYL TAB BACK OVER INSULATION <br />fREMOVE EXCESS INSULATION <br />FROM WALL ROLLS <br />DOUBLE FACED WHICH EXTEND PAST <br />TOP OF EAVE STRUT <br />TAPE AND FOLD VINYL TAB <br />BACK OVER INSULATION. <br />BASE ANGLE—, <br />OR BASE CHANNEL <br />REMOVE EXCESS INSULATION <br />TO PREVENT THE <br />PANEL FROM BULGING. <br />INSULATION MUST BE <br />,-CUT OFF AT FINISHED <br />FLOOR, NOT AT BOTTOM <br />OF SHEET NOTCH. <br />DOUBLE FACED <br />TAPE <br />INSULATION DETAIL <br />G19INSULATION NOT BY ACI <br />ENGINEERING SEAL <br />This certification covers parts <br />fabricated and delivered by the <br />manufacturer only and excludes <br />parts such as doors, windows, <br />foundation design, and erection of <br />the building. Sealed drawings do <br />not constitute an agreement that <br />the signed engineer is acting as <br />the engineer of record for the <br />overall project. <br />NI Bolts labeled as a 1/2' x i" A307 Bolt <br />Have been replaced with the Zinc <br />1/2" x 1 1/4" Flange Bolt and Nut Shown Below. <br />KE I H SHE.DD <br />459 WOODLAND RD <br />BATESVILLE, MS. 38606 <br />PE# 48014 <br />.����ll <br />\AN , P <br />�i <br />�� .•SAG E N SF• � pis ile t has been electroniealh <br />No 48014 '�°�'`1°d sealed bs Keith P_ Shedd. <br />F-G- using a Digital Signature and <br />* t * data printed copies of this document <br />* - are not considered sisued and sealed <br />STATE OF <C!: and the Signature must be %en ied (,it <br />amelectronic copies <br />�'�•,S�ONA� ����` 06/13/2021 <br />O <br />0 N <br />� Ln <br />C" <br />O Ln <br />Ln <br />ro <br />U <br />L <br />O <br />O - <br />—p U <br />C) E <br />I � <br />(D (D <br />( Q <br />C11 <br />U N <br />O <br />m <br />CUSTOMER <br />PROJECT <br />x <br />tn <br />FW- <br />tA <br />} <br />N <br />Z <br />a <br />m <br />ENG BY: <br />MNF <br />CAD BY: <br />WJD <br />DEr BY: <br />WJD <br />CKD BY: <br />JIM <br />JOB NUMBER : <br />B21-1794 <br />DWG NUMBER B <br />EP11 of 13 <br />