|
FOLD UP WEATHER
<br />RESISTIVE BARRIER &
<br />WEATHER RESISTIVE
<br />BARRIER
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />TEMPORARILY SECURE
<br />DOOR ROUGH OPENING
<br />SLOPE
<br />WEATHER
<br />0.3 in: 12.0 in
<br />R703.1 General. Lxterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />�RESISITIVE
<br />BARRIER
<br />WOOD FRAME CONSTR.(0.6
<br />cm: 30.5 cm)
<br />include flashing at described in Section R703.4,
<br />TAPE EXTERIOR
<br />SELF -ADHERED FLASHING 3/4"-1" BEAD OF CONSTR.
<br />3• SHEATHING
<br />BY LAPPING DOWN ADHESIVE TO BE APPLIED UNDER
<br />SELF -ADHERED FLASHING
<br />OVER RIM JOIST AND UP THRESHOLD OF DOOR AND
<br />WALL BY 6 IN. RETURN UP JAMB 6". USE LIQUID
<br />R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of
<br />cnssenna�eomnNoowl .;' -
<br />2
<br />Q NAIL BRAND OR EQUAL WEATHER
<br />EXTERIOR
<br />CEMT. FIN.
<br />water within the Wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means
<br />Q \ PROOF CAULKING
<br />of draining to the exterior water that penetrates the exterior cladding.
<br />WEATHER
<br />RESISITIVE
<br />SELF -ADHERED FLASHING
<br />BUILDING PAPER
<br />2
<br />BARRIER
<br />SEAL TOPS OF JOISTS
<br />% WIRE LATH
<br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />1�
<br />UNDER DECKING SUBFLOOR
<br />other approved Water -resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied
<br />SELF -ADHERED FLASHING
<br />(SEE DETAIL WP07) ° °
<br />_ _ _
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6
<br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The
<br />HEAD FLASHING TIE-IN INSTRUXre weal
<br />\
<br />No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and
<br />1. Cut, fold up &temporarily secure weather
<br />RIM JOIST
<br />,
<br />%
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />THESE DETAILS ARE GENERIC AND
<br />resistive barrier above header to allow for
<br />flashing installation
<br />�
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold barrier back head
<br />' '',
<br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over
<br />wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade
<br />BE USED.
<br />weather resistive over
<br />flashing and seal with tape
<br />D paper. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing
<br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />Scale: NTS
<br />SELF -ADHERED FLASHING
<br />FLANGED WINDOW 1
<br />SELF -ADHERED FLASHING
<br />1
<br />SELF -ADHERED FLASHING
<br />'
<br />Exception: Where the water -resistive barrier that is over wood sheathing has a water resistance
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />CEMT. FINISH SILL/ POTSHELF/CHIMNEY SHOULDER
<br />applied -based
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />substantially nonwater-absorbing layer or designed drainage space.
<br />EXTERIOR SHEATHING
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />EXTERIOR SHEATHING
<br />3/4"-V BEAD OF CONSTR. INSTALL SELF -ADHERED
<br />ADHESIVE TO BE APPLIED UNDER FLASHING JAMB & HEAD
<br />NEEDED IN CORNERS ADHESIVE
<br />ASPHALT ADHESIVE
<br />THROUGH SELF -ADHERED
<br />R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be
<br />3/8" CEMENT
<br />PLASTER
<br />THRESHOLD OF DOOR AND RETURN FLASHING, SEE
<br />FLASHING SELF -ADHERED FLASHING
<br />applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied
<br />pp g g pp
<br />12 MIL DRYLOK CMU - MASONRY BLOCK
<br />UP JAMB 6". USE LIQUID NAIL BRAND FLANGED WINDOW
<br />OR EQUAL WEATHER PROOF CAULKING (SEE DETAIL WP01)
<br />membranes used as flashing shall be applied in accordance with the manufacturers instructions. All flashing shall be applied in a manner to
<br />EXTREME
<br />REFER TO TECHNICAL
<br />SCORED
<br />prevent the entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />WINDOW
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />RELEASE PAPER
<br />Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />FASTENER
<br />1) SEALANT AT
<br />SELF -ADHERED FLASHING
<br />SELF -ADHERED FLASHING,
<br />(BEFORE FOLDING, SCORE
<br />RELEASE TO EXPOSE
<br />the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />4) SEALANT JOINT WINDOW BUCKTO
<br />EXTEND A MINIMUM 6"
<br />PAPER
<br />ADHESIVE AS SHOWN)
<br />contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as
<br />OUTSIDE EDGE OF ` MASONRY
<br />WINDOW BUCK o
<br />BOTTOM OF TICALLY FROM
<br />flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />2) SEALANT JOINT
<br />"' "
<br />THRESHOLD
<br />p
<br />shall be Installed at the following locations:
<br />5) SEALANT FROM INSIDE EDGE OF
<br />WINDOW FRAME WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />°
<br />SECTION -A (SEE DETAIL WP02)
<br />..
<br />AND EXTEND TO
<br />°
<br />1.1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />WINDOW FRAME
<br />MASONRY ATTACHED
<br />SELF -ADHERED FLASHING
<br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />6) TOOLED SEALANT PER CODEREQUIREMENTS
<br />°
<br />O `
<br />2
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />BEAD BRIDGING
<br />following:
<br />FRAME CLADDING AND WINDOW
<br />2
<br />SELF -ADHERED FLASHING
<br />5
<br />1.1 The fenestration manufacturers installation and flashing instructions, or for applications not addressed in the fenestration
<br />� g
<br />3) SEALANT WINDOW FRAME T
<br />WINDOW BUCK ALL THE WAY
<br />NAILING FLANGE
<br />1
<br />''
<br />4
<br />manufacturer's instructions, in accordance with the flashingmanufacturer's instructions. Where flashing instructions or details
<br />2
<br />AROUND, INCLUDING SILL.
<br />2
<br />SEAL TOPS OF JOISTS
<br />6
<br />are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING p
<br />8
<br />UNDER DECKING
<br />2
<br />7
<br />subsequent drainage. Openings usin an flashing shall incorporate flashing or protection at the head and sides.
<br />q gg p g p g
<br />FLANGE
<br />(SEE DETAIL WP07)
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />1.3 1.3. In accordance with other approved methods.
<br />SCS 06 05 CMU INSTALLATION 6 POINT BUCK AND
<br />SELF -ADHERED FLASHING
<br />1
<br />SELF -ADHERED FLASHING
<br />1
<br />SELF -ADHERED FLASHING
<br />,
<br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />HALF ROUND WINDOW
<br />EXTERIOR DOOR WITH DECK
<br />INSIDE CORNER
<br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />Ground
<br />3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />4.4.Continuously above all projecting wood trim.
<br />SHEATHING
<br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6.6.At wall and roof intersections.
<br />- --- - - - _
<br />Water Resistant Barrier
<br />7.7.At built-in utters.
<br />g
<br />JAMB, SILL AND HEAD DETAIL
<br />Lath
<br />APPROVED SHEATHING
<br />SELF -ADHERED FLASHING
<br />Sheathing
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />APPROVEDHOTRAWRAP
<br />PATCH
<br />STRUCTALATH TWIN TRACK 2.5
<br />� � �
<br />\�
<br />_ Stucco
<br />-
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />3/4" CEMENT PLASTER
<br />r
<br />12 MIL (min) DRYLOK EXTREME
<br />\
<br />APPROVED FLASHING TAPE
<br />`',
<br />l DOUBLE
<br />O
<br />° °°
<br />a d T
<br />7/8" Cement Plaster
<br />"V" SEALANT SOCKET WITH
<br />JOIST
<br />� I
<br />a a °
<br />TOOLED APPROVED SEALANT
<br />i� � I II
<br />I i
<br />SINGLE �i J WOOD BEAM
<br />�
<br />°
<br />° ° °
<br />n accordance with 7/8" Cement Plaster
<br />i
<br />j JOIST \ BELOW
<br />-- 1 SELF -ADHERED FLASHING
<br />Foundation Wall ° a
<br />°
<br />ASTMC926e with
<br />:• \ i �\
<br />SELF -ADHERED FLASHING
<br />a ° ° ° d
<br />ASTMC926
<br />.,. •
<br />2
<br />° ° °
<br />°
<br />M e ace metal
<br />lathe in accordance Felt backed metal
<br />v-.
<br />SELF ADHERED SELF -ADHERED
<br />3" MIN
<br />4
<br />with ASTM C1063 lathe in accordance
<br />FLASHING FLASHING
<br />2
<br />o
<br />5
<br />Building Paper with ASTMC1063
<br />,�; Building Paper
<br />7/16" O.S.B.
<br />sheathing O.S.B.
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />SELF -ADHERED FLASHING
<br />SELF -ADHERED FLASHING
<br />FOUNDATION WEEP SCREED
<br />sheathing
<br />, : Metal �; sheathing
<br />EXTRUDED SHOULDER
<br />DECK JOIST
<br />OUTSIDE CORNER
<br />.. Flashing
<br />Weep Screed
<br />SELF -ADHERED FLASHING
<br />2x FRAMEWALL
<br />l�
<br />Installed As Per
<br />Manufact. Specs.
<br />PRODUCTSDETAILS
<br />I
<br />i STRIP OF SAF LEGEND
<br />1 SELF ADHERED FLASHING (SAF)
<br />Maintain Stampede or similar
<br />Bottom of cauk bottom
<br />TILE FINISH
<br />I
<br />H
<br />DRAINAGE PLANE WRB DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />Weep Screed joint only
<br />W
<br />I I BARRIER (WRB) - - - - - - -
<br />1 1 /2 t0 2"
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />1/2" DUROCK
<br />>
<br />BOND BREAK WEATHER RESISTANT BARRIER- - -
<br />II BOND BREAK WRB SELF FURRING (SF) LATH
<br />Above Roof Weep Screed
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />a
<br />I I PLASTER ACCESSORY
<br />'OSB%
<br />Sheathing Installed As Per
<br />I : SF LATH SHEATHING, PLYWOOD, DENSGLASS
<br />Manufact, Specs.
<br />1'4' PER PLAN
<br />?
<br />I i
<br />Detail Instructions
<br />Refer to the number marked as O# in each detail that corresponds to the
<br />, „
<br />1 0 PER PLAN
<br />I I" WRAP DP WRB ONTO
<br />THE VERTICAL
<br />I
<br />„
<br />1/2 Cementitious
<br />Cement Plaster
<br />I SURFACE TO TOP OF
<br />Decorative Finish
<br />numbered items in the list of instructions below:
<br />l FLANGE AS AN AIR
<br />in accordance
<br />II BARRIER
<br />with ASTMC926 ®o°® All inside and
<br />1. Install self -adhered flashing in order as shown by numbers
<br />SLOPE
<br />8" CMU
<br />__ i i I 3-1/2" INCH FLANGE
<br />over wood 2nd ®°®°` ° ®°®
<br />floor °®°' ®•®®®® outside corner will
<br />2. Install flashing and weather resistive barrier to form water shedding®°
<br />_ -
<br />'
<br />need to be miter
<br />laps
<br />4" OR8" CMU Qs °a
<br />- ----------------
<br />------------------J I� I
<br />F
<br />° ®•° ° cut and caulked all
<br />3. Self -adhered flashing can be substituted for building paper
<br />(PER SEAT DEPTH) F 1
<br />z
<br />z
<br />I I STRUCTURAL FRAMING
<br />'°®•®,. ®•� buttjoints need to
<br />° °•° ®'®°°
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />-'
<br />FILL WITH GROUT 1 1 a
<br />a
<br />0-
<br />_
<br />STRUCTURAL SHEATHING
<br />becaulked using
<br />• °,°°o o • Stampede or sim.
<br />embedded in the adhesive layer) - for ease of installation and to
<br />�,� r,� ..
<br />minimize scoring cuts
<br />a
<br />LU
<br />d
<br />THIS GAP IS A RESULT OF ;' ,:
<br />PLASTER STOP NATURAL SHRINKAGE. STRIP OF SAF
<br />caulk for all
<br />5. Remove all release paper per standard installation instructions and
<br />p p p
<br />° a
<br />=
<br />�- - - - - - - - - DO NOT SEAL.
<br />CONTINUOUS BACKER DRAINAGE PLANE WRB
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />°
<br />ROD & SEALANT DRIP SCREED PLASTIC ; I
<br />Minimum)
<br />SLOPED MUD BED d a
<br />'-
<br />=
<br />LU
<br />ACCESSORY 6 I BOND BREAK WRB
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />'_
<br />a
<br />I --I
<br />LLI
<br />W
<br />o
<br />I Ij I SF LATH
<br />r't
<br />fit tight to
<br />d
<br />VINYL SHOWER PAN I I
<br />I
<br />corner
<br />d
<br />_
<br />/'-'� , ; ;l .
<br />Note:
<br />8. Mechanically fasten as necessary
<br />~ °�
<br />"'
<br />---------- '-----------`----- ' i '
<br />The building paper and metal lath must be
<br />SLOPE a
<br />-
<br />i l
<br />°
<br />Cement installed over the top of the weep screed.
<br />° ° - - d a
<br />PLASTER STOP J�
<br />Plaster
<br />4
<br />CONTINUOUS BACKER ROD
<br />over
<br />a d
<br />& SEALANT
<br />1 st floor
<br />4
<br />4
<br />CEMENTITIOUS FINISH
<br />WEEP SCREED DETAIL
<br />SHOWER SEAT
<br />SOFFIT/CANTILEVER .
<br />SCALE: NOT TO SCALE
<br />c�
<br />s �
<br />ee c� c
<br />37 O
<br />_
<br />u3 N �
<br />>
<br />cu
<br />to,
<br />Ccd`:m
<br />�. CD
<br />N C '9
<br />c E
<br />� o
<br />a
<br />N
<br />o_
<br />�1-
<br />I-
<br />0
<br />To the best of the Engineers knowledge, information and belief,
<br />the structural plans and specifications contained within these
<br />drawings comply with the 2020
<br />Florida Building Code -
<br />Residential
<br />7th Edition. Engineers signature and seal is only for
<br />the structural
<br />engineering portions of the drawing pages bearing
<br />Engineers
<br />signature and seal.
<br />W
<br />Q
<br />d E
<br />a
<br />co 8
<br />o
<br />0
<br />a) So Cc: N r
<br />D?
<br />ft7
<br />5 V7 N 0 #
<br />U) ti ti n J
<br />vi
<br />Q
<br />Qj M V # w
<br />J w
<br />w
<br />CU a
<br />13w
<br />JU_LL
<br />-OZ 6 Cco O
<br />t
<br />YwJ
<br />1%Qr`-W
<br />Zd
<br />�L
<br />3:0m
<br />ZN��
<br />IL
<br />U) ,
<br />co Z
<br />Z
<br />OU
<br />0
<br />W
<br />U C,
<br />N M
<br />o
<br />00
<br />z W �
<br />z o �
<br />Q
<br />J
<br />a �
<br />:%i
<br />a
<br />�v0o
<br />LL
<br />w
<br />ca
<br />O-�
<br />w o
<br />�y N
<br />UW&
<br />U
<br />W J
<br />m
<br />� ®
<br />N O
<br />CD�w
<br />M
<br />M
<br />z �
<br />o
<br />Z
<br />Z
<br />LA.
<br />ct- E
<br />ZU
<br />oLL
<br />Zo
<br /><N
<br />�
<br />V
<br />Fw,z
<br />z®
<br />oa
<br />CU
<br />7 E
<br />O
<br />MU
<br />X U
<br />dp
<br />z
<br />Up
<br />U
<br />�Z
<br />Z
<br />N r0
<br />wo
<br />i°y,
<br />.�
<br />m
<br />� �
<br />o
<br />Z
<br />Z
<br />�
<br />U
<br />�0,
<br />Z
<br />¢w
<br />z
<br />a0
<br />W
<br />S{
<br />U3
<br />2=K
<br />�&
<br />pow
<br />yz
<br />a
<br />=3
<br />o
<br />w,
<br />7r
<br />}°
<br />�D
<br />�t
<br />z¢
<br />a
<br />03
<br />.s CN
<br />> LO
<br />C
<br />e
<br />0
<br />o
<br />>
<br />W
<br />r
<br />�
<br />�
<br />rn
<br />CU p
<br />o
<br />Q
<br />M
<br />�
<br />r
<br />o
<br />O
<br />N
<br />00
<br />CO
<br />0
<br />Q
<br />0
<br />70
<br />o N
<br />LO
<br />_
<br />-
<br />d N
<br />0
<br />co
<br />r
<br />CL
<br />LO
<br />c.6
<br />,--
<br />a
<br />w 4
<br />o
<br />Z
<br />E
<br />ca
<br />a
<br />E
<br />U 0
<br />ai
<br />¢ p
<br />c
<br />JOB
<br />NO: 22-08393-08388
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />
|