|
T.O. BOND BEAM
<br />l S' V.LF.
<br />G.C. TO PROVIDE TEMPORARY
<br />SAW CUT AND REMOVE INSIDE SHELL ONLY
<br />SUPPORT & SHORING WITH BACK
<br />AS NEEDED TO DRILL AND HILTI HIT HY 150
<br />TO BACK CHANNELS
<br />EPDXY SET (1) #5 DOWEL MIN. OF 6" INTO
<br />EXISTING BOND BEAM, PROVIDE MIN. OF 24"
<br />LAP W/ VERT. REINF., TYR
<br />0 0_�',
<br />NEW PRECAST LINTEL W/ (1) #5
<br />CONT, (1)#5 DOWEL EA. END TO
<br />o
<br />0 0 0
<br />0 0 0
<br />o
<br />0
<br />AND REMOVE SHELL
<br />ABBO LL
<br />VERT. REINF. AS SHOWN AND
<br />ERIDE
<br />ABOVE NTEL ONLY E REQUIRED TO
<br />GROUT SOLID, TYP.
<br />ENSURE FULLY GROUTED CELLS, TYR
<br />T.O. NEW OPENING
<br />T4'AEF.
<br />INSTALL (1) #5 VERT. [CENTER SPACING]
<br />THROUGH JAMB CUTS (REF. SK4-2) AS SHOWN
<br />AT EA. SIDE OF OPENING, LAP AND TIE PER
<br />ALL CMU CELLS
<br />REQUIREMENTS OF GEN. NOTES IF 2 BAR SETS
<br />BELOW FINISH
<br />REQUIRED FOR INSTALLATION PURPOSES.
<br />FLOOR TO BE
<br />GROUT FILLED.,
<br />V.I.F.
<br />DRILL AND HILTI HIT HY 150'EPDXY SET
<br />(1) #5 DOWEL MIN! OF 6" INTO EXISTING
<br />GROUTED CMU BASE, PROVIDE MIN. OF 24"
<br />T.O. SLAB
<br />LAP W/ VERT. REINF.
<br />V-VAEF.
<br />T.O. FOOTING
<br />4-V V.I.F.
<br />Interior Elevation
<br />SCALE:N.T.S.
<br />REF:
<br />EXISTING RAIN HOOD EXISTING SCONCE LIGHT NEW RAIN HOOD
<br />OVER REAR DOOR TO FIXTURE TO BE RELOCATED OVER NEW DOOR.
<br />BE REPLACED WITH TO 2' TO THE SIDE OF NEW RE: DOOR SCHEDULE
<br />LARGER RAIN HOOD DOOR. REWIRE TO NEW
<br />TENANT PANEL. RE: E101
<br />EX ® ® EX
<br />0
<br />7 EM
<br />NEW 2' X 4' ACOUSTICAL TILE
<br />CEILINGS MOUNTED AT 10'-0'
<br />ABOVE FLOORS IN SPACE
<br />F1-F3 IN RESTROOMS ONLY
<br />NO CEILING IN MAIN SPACE
<br />OR STOCK ROOM OF F1-F3.
<br />STRUCTURE ABOVE TO BE
<br />PAINTED WHITE.
<br />8' LIGHTS SUSPENDED AT
<br />12'-0"AFF. RE: E201
<br />EXISTING RAIN
<br />HOODS OVER
<br />REAR DOORS
<br />TO REMAIN AS IS
<br />EXISTING LIGHTS IN
<br />FIRE RISER ROOM
<br />TO REMAIN AS IS.
<br />EXISTING CMU, SAW CUT JAMBS AS SHOWN
<br />FOR ADDITION OF VERT. REINF. AND GROUT
<br />EXISTING CMU, SHOWN WITH ADDED
<br />REINF. (CENTER SPACING) AND GROUT
<br />Masonry Vert. Reinforcing
<br />SCALE:N.T.S.
<br />2REF:
<br />ALL EXISTING REBAR OUTSIDE OF THE NEW 6'-4' X Te
<br />CMU OPENING SHALL REMAIN UNDAMAGED. ALL DEMO
<br />WORK AT THE JAMBS AND HEAD OF THE NEW OPENING
<br />SHALL BE PERFORMED CAREFULLYAND SURGICALLY
<br />SO AS NOT TO DAMAGE ANY OF THE EXISTING REBAR.
<br />l'-0' MIN. EXISTING CMU AND SLAB SECTION
<br />TO BE REMOVED, GC TO MINIMIZE
<br />EXTENTS OF SLAB SECTION REMOVED
<br />GC V.I.F. ALL CELLS GROUTED
<br />SOLID BELOW FIN. FLR.
<br />EXISTING FOOTING TO REMAIN
<br />V.I.F.
<br />Slab @ New Opening, Demo
<br />SCALEAT.S.
<br />3 REF:
<br />CEILING PLAN GENERAL NOTES:
<br />1. ALL NEW CEILINGS SHALL BE 2' X 4' ACT MOUNTED
<br />AT 10'-0"AFF WITH NO INSULATION.
<br />2. ON THE FRONT OF THE BUILDING, THE EXISTING
<br />DECORATIVE SCONCE FIXTURES SHALL REMAIN WIRED
<br />AS IS TO THE EXISTING HOUSE PANEL.
<br />3. EXISTING REAR WALL MOUNTED LIGHTS SHALL BE WIRED
<br />TO THE NEW TENANT PANELS VIA NEW LIGHT SWITCHES.
<br />4. THE EXISTING EXIT AND EMERGENCY LIGHTS SHALL BE
<br />REUSED IF POSSIBLE. THEY SHALL BE RE -WIRED FROM
<br />THE HOUSE PANEL TO THE NEW TENANT PANELS.
<br />5. ALL NEW LIGHTS SHALL BE WIRED TO THE NEW PANELS.
<br />6. THE RTUS ARE EXISTING AND SHALL REMAIN. ALL NEW
<br />SUPPLY DIFFUSERS, RETURN GRILLES, AND EXHAUST FANS
<br />SHALL BE TIED INTO THE EXISTING RTUS VIA NEW DUCTWORK.
<br />7. THE EXISTING RTUS AND THE NEW EXHAUST FANS SHALL
<br />BE WIRED TO THE NEW TENANT PANELS.
<br />8. THE FIRE SPRINKLER HEAD LAYOUT SHALL BE DETERMINED
<br />BY THE FIRE SPRINKLER SUBCONTRACTOR'S SPECIALTY
<br />ENGINEER DURING THE DESIGN OF HIS SHOP DRAWINGS.
<br />9. THE EXISTING SPRINKLER HEADS SHALL BE TURNED
<br />DOWN & REPOSITIONED AS NEEDED TO COORDINATE
<br />WITH HVAC, ELECTRICAL, AND PLUMBING.
<br />EXISTING SCONCE EXISTING RAIN
<br />LIGHT FIXTURE HOODS OVER
<br />TO BE REWIRED. REAR DOORS
<br />RE: E101 TO REMAIN AS IS
<br />n n
<br />EM EM
<br />F-C - -
<br />EM
<br />EMERGENCY LIGHT FIXTURE (EM).
<br />WIRED TO NEW TENANT PANEL.
<br />REUSE EXISTING IF POSSIBLE. RE: E201
<br />,, F.0 ® Ex
<br />EXISTING CANOPY
<br />LIGHT FIXTURE
<br />TO REMAIN AS IS
<br />STRIPED FABRIC AWNING
<br />TO BE REPLACED WITH ,
<br />SOLID FABRIC TO MATCH
<br />ADJACENT. AWNING
<br />FRAME TO REMAIN AS IS.
<br />EXISTING SCONCE
<br />LIGHT FIXTURE F 1 F-
<br />TO REMAIN AS IS
<br />NEW HVAC RETURN AIR
<br />GRILLE MOUNTED
<br />IN CEILING. RE: M101
<br />EM VILFL-17 EM
<br />Fill L EXISTING SOLID
<br />i
<br />L STRIPED FABRIC AWNING
<br />L EXISTING SOLID
<br />FABRICAWNING
<br />TO BE REPLACED WITH
<br />FABRICAWNING
<br />TO REMAIN AS IS
<br />SOLID FABRIC TO MATCH
<br />TO REMAIN AS IS
<br />ADJACENT. AWNING
<br />--
<br />FRAME TO REMAIN AS IS.
<br />EXISTING CANOPY
<br />EXISTING SCONCE
<br />ACCESS HATCH
<br />LIGHT FIXTURE
<br />TO REMAIN AS IS
<br />TO REMAIN AS IS
<br />EXISTING SCONCE
<br />LIGHT FIXTURE
<br />F 4 }
<br />F 6 :!
<br />TO REMAIN AS IS
<br />EXISTING SCONCE
<br />LIGHT FIXTURE
<br />TO BE REWIRED.
<br />RE: E101
<br />1-.
<br />NEW EXHAUST FANS
<br />IN RESTROOM
<br />CEILINGS. RE: M101
<br />NEW 2 X 4 CEILING
<br />MOUNTED LIGHT
<br />FIXTURES. RE: E101
<br />NEW HVAC SUPPLY AIR
<br />DIFFUSER MOUNTED
<br />IN CEILING. RE: M101
<br />NEW Z X 4' ACOUSTICAL TILE
<br />CEILINGS MOUNTED AT 10'-0'
<br />ABOVE FLOORS IN RESTROOMS
<br />AND IN MAIN ROOM OF F4
<br />1
<br />I
<br />i
<br />i
<br />I
<br />NEW EXIT LIGHT EXISTING SCONCE
<br />FIXTURE (EX) WIRED TO NEW LIGHT FIXTURE
<br />TENANT PANEL. REUSE EXISTING TO REMAIN AS IS
<br />IF POSSIBLE. RE: E201
<br />F-"t'_ 0:IF-11
<br />Door Schedule
<br />DOOR
<br />FRAME
<br />HARD
<br />WARE
<br />TYPE
<br />#
<br />MATERIAL
<br />SIZE (EACH)
<br />MATERIAL
<br />DETAILS
<br />SET
<br />A
<br />DBL
<br />HM
<br />3'-0" X 7'-0"
<br />HM
<br />H1, J1, S1
<br />1
<br />X 13/4"
<br />B
<br />SGL
<br />ALUM.
<br />3'-0' X 7'-0'
<br />ALUM.
<br />H2, J2, S2
<br />2
<br />X 13/4'
<br />C
<br />DBL
<br />ALUM,
<br />3'-0' X
<br />ALUM.
<br />H2, J2, S2
<br />3
<br />X 13/4"
<br />D
<br />SGL
<br />WOOD
<br />T-0" X V-8"
<br />X 13/4'
<br />WOOD
<br />H3, J3, S3
<br />4
<br />E
<br />DBL
<br />ABS
<br />3'-0' X 8'-0"
<br />ABS
<br />J4
<br />5
<br />X 1314'
<br />vp
<br />F
<br />SGL
<br />HM
<br />3'-0' X 7'-0'
<br />HM
<br />H1, J1, S1
<br />6
<br />X 1314'
<br />NOTES:
<br />1. PAINT EXTR. OF DOOR "A" TO MATCH EXISTING. LEAVE INTR. PAINT READY.
<br />2. PAINT INTR. OF DOOR'D" TO MATCH RESTROOM WALLS. EXTR. SHALL
<br />BE
<br />PAINT READY. PROVIDE REINFORCED PANELTOACCEPT CLOSER.
<br />3. DOOR "E" IS A DOUBLE ACTING IMPACT TRAFFICE DOOR
<br />(RUBBAIR ULTRA-LITE WITH WINDOWS).
<br />NOA Schedule
<br />BUILDING
<br />MANUFACTURER
<br />NOA#
<br />EXPIRATION
<br />MATERIAL
<br />/ MODEL #
<br />DATE
<br />STOREFRONT
<br />YKK-AP
<br />08-0715.14
<br />08-07-13
<br />WINDOWS
<br />YES 45 FS
<br />STOREFRONT
<br />YKK-AP
<br />07-M.08
<br />04-16-12
<br />DOORS
<br />35D, MEDIUM STILE
<br />HOLLOW METAL
<br />CECO
<br />09-0505.09
<br />08-05-14
<br />REAR DOORS
<br />6-0 X 7-0 SWINGING DOOR
<br />NOTES:
<br />1. THESE NONS ARE PROVIDED TO COMPLY WITH THE FLORIDA BUILDING
<br />COMMISSION RULE 913-72. THESE APPROVALS HAVE BEEN REVIEWED FOR
<br />APPLICATION ON THIS PROJECT. THE ARCHITECTS SIGNATURE AND SEAL
<br />DOES NOT REPLACE OR SUPERCEDE THE PROFESSIONAL RESPONSIBILITY
<br />OF THE INDIVIDUAL NONS OR INTERNAL DESIGN COMPONENTS THEREOF.
<br />2. THE CONTRACTOR MAY SUBMIT ALTERNATES FOR ANY OF THE BUILDING
<br />COMPONENTS ON THIS LISTAS LONG AS IT DOES NOT VIOLATE ANY
<br />EXISTING WARRANTIES THAT MAY BE IN EFFECT. IN ORDER TO RECEIVE
<br />APPROVAL ON ANY ALTERNATES, THE GC MUST SUBMIT PRODUCT
<br />INFORMATION TO THE OWNER FOR REVIEW AS WELL AS TO THE LOCAL
<br />JURISDICTION AS REQUIRED FOR PERMITTING AND C.O.
<br />3. THE MAXIMUM DESIGN PRESSURE THAT THESE COMPONENTS NEED TO
<br />WITHSTAND IS + / - 36.1 PSF. IMPACT RESISTANCE IS NOT REQUIRED.
<br />SAWCUT CMU,
<br />POINT IN RAIN
<br />HOOD, CAULK
<br />CONT
<br />22 GA. GALV.
<br />MTL. RAINHOOD,
<br />PAINT TO
<br />MATCH DOORS.
<br />HOOD TO
<br />EXTEND 8'
<br />PAST EDGE
<br />OF DOOR ON
<br />BOTH SIDES
<br />GROUT
<br />SOLID
<br />CONT. CAULK FULL DOOR
<br />PERIMETER WEATHER
<br />STRIP
<br />4"
<br />HEAD DETAIL - H1
<br />GROUT SOLID
<br />FULL DOOR
<br />WEATHER STRIP
<br />MASONRY JAMB
<br />ANCHOR AS REQ.
<br />\ CAULK PERIMETER
<br />CONT. TYP
<br />JAMB DETAIL - J1
<br />DOOR FRAME
<br />'OND)
<br />THRESHOLD
<br />V MASTIC (TYR)
<br />iH FLOOR
<br />-LOOR PLAN
<br />SILL DETAIL - S1
<br />COORDINATE ALL EXTERIOR DOOR DETAILS
<br />5 Door Details WITH THE REQUIREMENTS OF THE ASSOCIATED
<br />SCALE: 3" = V-0" FLORIDA PRODUCT APPROVAL (NOA)
<br />Hardware Schedule
<br />HARDWARE SET # 1: (REAR HOLLOW METAL DOOR)
<br />(6) - HAGER 4-1/2' X 4-10 BUTT FULL MORTISE
<br />HINGES NO. BB1191 (NRP). STAINLESS
<br />STEEL HINGES W/ STAINLESS STEEL PINS
<br />(1) - LOCKSET SCHLAGE AL53PD'ENTRANCE
<br />LOCK'. FINISH 626 (US 26D) SATIN CHROME
<br />(1) - CLOSER - LCN NO.4040. STANDARD POWDER
<br />COAT ALUMINUM FINISH. STANDARD PLASTIC
<br />COVER. MOUNTED ON INTERIOR SIDE
<br />(1) - SET FULL WEATHERSTRIP
<br />(1) - DOOR SWEEP
<br />(1)-ALUMINUM THRESHOLD (ADA COMPLIANT)
<br />(1) - RAINHOOD. RE: HEAD DETAIL
<br />(1) - ASTRAGAL
<br />(1) - FLOOR BOLT FOR SECONDARY LEAF
<br />(1)-1.5',180 DEGREE PANORAMIC VIEWER
<br />(1) - DOOR STRIKE COVER PLATE
<br />HARDWARE SET # 2: (STOREFRONT DOOR)
<br />(1) - SET SINGLE ACTING OFFSET PIVOT HINGES
<br />(1) - DOOR CLOSER - NORTON 1601(ADJUSTABLE FORCE)
<br />(1) - MILL FINISH ALUMINUM THRESHOLD (FOR
<br />OFFSET PIVOTAND OVERHEAD CLOSER)
<br />(1) -ADAMS RITE MS+1890 DEADLOCK/ LATCH COMBINATION
<br />(1) -ADAMS RITE 4590 LATCH PADDLE DEVICE
<br />(1) -ADAMS RITE STANDARD LATCH STRIKE
<br />(1) - CYLINDER - SCHLAGE (7PIN) MORTISE
<br />(1) - CP II DOOR PUSH & CO-9 PULL #14
<br />(1) - SEALAIR WEATHERING SYSTEM & EPDM
<br />BLADE SURFACE ATTACHED SWEEP STRIP
<br />(1) - STENCILLED NOTE: "DOOR TO REMAIN
<br />UNLOCKED DURING STORE OPERATION'
<br />HARDWARE SET # 3: (STOREFRONT DOOR)
<br />(2) - SET SINGLE ACTING OFFSET PIVOT HINGES
<br />(2) - DOOR CLOSER - NORTON 1601 (ADJUSTABLE FORCE)
<br />(1) - MILL FINISH ALUMINUM THRESHOLD (FOR
<br />OFFSET PIVOT AND OVERHEAD CLOSER)
<br />(1) - ADAMS RITE MS+1890 DEADLOCK I LATCH COMBINATION
<br />(1) - ADAMS RITE 4590 LATCH PADDLE DEVICE
<br />(1) -ADAMS RITE STANDARD LATCH STRIKE
<br />(1) - CYLINDER - SCHLAGE (7PIN) MORTISE
<br />(2) - CP II DOOR PUSH & CO-9 PULL #14
<br />(1) - SEALAIR WEATHERING SYSTEM & EPDM
<br />BLADE SURFACE ATTACHED SWEEP STRIP.
<br />(1) - STENCILLED NOTE: "DOOR TO REMAIN
<br />UNLOCKED DURING STORE OPERATION'
<br />HARDWARE SET # 4: (RESTROOM DOOR)
<br />(3) - HAGER 4-1/2' X 4-1/2' BUTT FULL MORTISE
<br />HINGES NO. BB1191(NRP). STAINLESS
<br />STEEL HINGES W/ STAINLESS STEEL PINS
<br />(1) - LOCKSET SCHLAGE AL40S 'PRIVACY LOCK'
<br />FINISH 626 (US 26D) SATIN CHROME
<br />(1) - CLOSER - LCN NO.4040. STANDARD POWDER
<br />COATALUMINUM FINISH. STANDARD PLASTIC
<br />COVER. MOUNTED ON INSIDE OF ROOM
<br />(1) - WALL STOP
<br />(3) - SILENCERS
<br />HARDWARE SET # 5: (STOCKROOM DOOR)
<br />(2) -10.5" X 23' SEALED VISION PANEL WINDOW
<br />EACH WITH RADIUS GASKET
<br />(1) - SET OF REMOVABLE FULL PERIMETER SEALS
<br />(2) - 8-3/4' HIGH STANDARD JAMB GUARDS
<br />(1) - HARDWARE: CAM LIFT 90 DEG. X 90 DEG.
<br />HARDWARE SET # 6: (REAR HOLLOW METAL DOOR)
<br />(3) - HAGER 4-1/2' X 4-1/2' BUTT FULL MORTISE
<br />HINGES NO. BB1191(NRP). STAINLESS
<br />STEEL HINGES W/ STAINLESS STEEL PINS
<br />(1) - LOCKSET SCHLAGE AL53PD'ENTRANCE
<br />LOCK". FINISH 626 (US 26D) SATIN CHROME
<br />(1) - CLOSER - LCN NO.4040. STANDARD POWDER
<br />COATALUMINUM FINISH. STANDARD PLASTIC dill
<br />COVER. MOUNTED ON INTERIOR SIDE
<br />(1) - SET FULL WEATHERSTRIP
<br />(1) - DOOR SWEEP
<br />(1) -ALUMINUM THRESHOLD (ADA COMPLIANT)
<br />(1) - RAINHOOD. RE: HEAD DETAIL
<br />(1) - DOOR STRIKE COVER PLATE
<br />�41
<br />HEAD DETAIL - H2
<br />ALUM.
<br />STOREFRONT
<br />SYSTEM
<br />ALUM. JAMB
<br />BEYOND
<br />ALUM. DOOR
<br />RE: DOOR
<br />SCHEDULE
<br />W I TF'.
<br />BELOW
<br />ru.um. uwr%
<br />RE: DOOR SCHEDULE
<br />JAMB DETAIL - J2
<br />SILL DETAIL - S2
<br />ALUM. JAMB BEYOND
<br />APPLIED SWEEP
<br />ALUM. THRESHOLD
<br />BY STOREFRONT
<br />INSTALLER
<br />EXISTING CONCRETE
<br />FLOOR SLAB
<br />EXISTING EXTR
<br />SIDEWALK
<br />�N
<br />oLu
<br />o�
<br />z
<br />U
<br />io
<br />Hardware Notes
<br />1. ADJUSTALL CLOSERS TOA5 LB MAX OPENING FORCE.
<br />2. ALL LOCK & PASSAGE SETS TO BE SCHLAGE GRADE OR BETTER.
<br />LOCKS NEED TO BE REKEYABLE.
<br />3. ALL DOORS & HARDWARE TO COMPLY WITH NFPA 101-5-2.1.5.
<br />4. ALL DOORS & HARDWARE TO COMPLY WITH THE FLORIDA
<br />ACCESSIBILITY CODE & THE ADA FEDERAL REGULATION CODES,
<br />UTILIZING A LEVER LATCH OR LOCKSET.
<br />5. FINAL CORE PROCESS FOR LOCKSETS & KEYING SHALL BE: THE
<br />SUBCONTRACTORS WILL INSTALLALL DOORS, FRAMES, HARDWARE
<br />& LOCKSETS.
<br />DOUBLE 2X BLOCKING MIN. ATJAMBS. PROVIDE EXACT
<br />SUPPORT RECOMMENDED BY DOOR MANUFACTURER -
<br />!STEEL ANGLE MOUNTED
<br />TO HEADER AND .JAMB
<br />HARDWARE COVER
<br />TOP MOUNTNG
<br />BRACKET
<br />1,/80 THICK � -
<br />ASS FACING
<br />LOWER
<br />PIVOT PIN
<br />8-3/4- STEEL'
<br />JAMB GUARD
<br />HEAD DETAIL - H3
<br />JAMB DETAIL - J3
<br />SILL DETAIL - S3
<br />6AM131>
<br />MOUNTING DETAIL
<br />OFFSET PIVOT HARDWARE
<br />DOOR ROTATED FOR CLARITY
<br />JAMB DETAIL - J4
<br />RE: WALL TYPES FOR
<br />FRAMING, SHEATHING, &
<br />INSULATION INFORMATION
<br />CONT. 2X WOOD BLOCKING
<br />AT ENTIRE PERIMETER OF
<br />ROUGH OPENING
<br />SOLID WOOD DOOR
<br />FRAME. PAINT INTERIOR
<br />TO MATCH DOOR. EXTR
<br />TO BE PAINT READY
<br />RE: DOOR SCHEDULE
<br />FLUSH HOLLOW CORE
<br />WOOD DOOR
<br />RE: DOOR SCHEDULE
<br />RE: WALL TYPES FOR
<br />FRAMING, SHEATHING, &
<br />INSULATION INFORMATION
<br />CONT 2X WOOD BLOCKING
<br />AT ENTIRE PERIMETER OF
<br />ROUGH OPENING
<br />FLUSH HOLLOW CORE
<br />WOOD DOOR
<br />RE: DOOR SCHEDULE
<br />SOLID WOOD DOOR
<br />FRAME. PAINT INTERIOR
<br />TO MATCH DOOR. EXTR
<br />TO BE PAINT READY
<br />RE: DOOR SCHEDULE
<br />HC WOOD DOOR. RE: SCHED.
<br />SOLID WOOD DOOR
<br />FRAME (BEYOND)
<br />COORDINATE UNDERCUT SIZE
<br />WITH MECHANICAL PLANS
<br />RE: FLOOR PLAN FOR
<br />FINISH INFORMATION
<br />�
<br />N
<br />Q
<br />O
<br />8
<br />�
<br />1
<br />^.,
<br />0
<br />Uw
<br />-_-w
<br />V _
<br />a
<br />a�
<br />� U
<br />�� 3
<br />3
<br />Cf)
<br />C
<br />0
<br />E
<br />E
<br />0
<br />CD
<br />L
<br />i
<br />N o
<br />6-+ J
<br />CU mm
<br />� Y
<br />U Q
<br />oes
<br />0
<br />M
<br />LjL m
<br />1 'J
<br />J
<br />r Q
<br />UL CD
<br />(n N
<br />ai00
<br />�
<br />ao
<br />J
<br />�--"lqt_
<br />w
<br />a CU F- >_
<br />o0 W
<br />Ca
<br />ai
<br />U
<br />U
<br />w
<br />CD
<br />w ry
<br />0
<br />w
<br />w
<br />a
<br />w
<br />~
<br />to
<br />W
<br />�
<br />a
<br />a.
<br />U
<br />0
<br />4
<br />N
<br />N
<br />S
<br />CN
<br />0
<br />a
<br />�
<br />z
<br />rn�'
<br />w
<br />co
<br />Z
<br />_
<br />N
<br />N
<br />?'
<br />0w
<br />m
<br />O
<br />TENANT BUILD OUT
<br />Al 03
<br />eN
<br />4 Reflected Ceiling Plan
<br />SCALE: 1/8' = V-V
<br />
|